--- /dev/null
+#ifndef __DANUBE_GPTU_DEV_H__2005_07_26__10_19__
+#define __DANUBE_GPTU_DEV_H__2005_07_26__10_19__
+
+
+/******************************************************************************
+ Copyright (c) 2002, Infineon Technologies. All rights reserved.
+
+ No Warranty
+ Because the program is licensed free of charge, there is no warranty for
+ the program, to the extent permitted by applicable law. Except when
+ otherwise stated in writing the copyright holders and/or other parties
+ provide the program "as is" without warranty of any kind, either
+ expressed or implied, including, but not limited to, the implied
+ warranties of merchantability and fitness for a particular purpose. The
+ entire risk as to the quality and performance of the program is with
+ you. should the program prove defective, you assume the cost of all
+ necessary servicing, repair or correction.
+
+ In no event unless required by applicable law or agreed to in writing
+ will any copyright holder, or any other party who may modify and/or
+ redistribute the program as permitted above, be liable to you for
+ damages, including any general, special, incidental or consequential
+ damages arising out of the use or inability to use the program
+ (including but not limited to loss of data or data being rendered
+ inaccurate or losses sustained by you or third parties or a failure of
+ the program to operate with any other programs), even if such holder or
+ other party has been advised of the possibility of such damages.
+******************************************************************************/
+
+
+/*
+ * ####################################
+ * Definition
+ * ####################################
+ */
+
+/*
+ * Available Timer/Counter Index
+ */
+#define TIMER(n, X) (n * 2 + (X ? 1 : 0))
+#define TIMER_ANY 0x00
+#define TIMER1A TIMER(1, 0)
+#define TIMER1B TIMER(1, 1)
+#define TIMER2A TIMER(2, 0)
+#define TIMER2B TIMER(2, 1)
+#define TIMER3A TIMER(3, 0)
+#define TIMER3B TIMER(3, 1)
+
+/*
+ * Flag of Timer/Counter
+ * These flags specify the way in which timer is configured.
+ */
+/* Bit size of timer/counter. */
+#define TIMER_FLAG_16BIT 0x0000
+#define TIMER_FLAG_32BIT 0x0001
+/* Switch between timer and counter. */
+#define TIMER_FLAG_TIMER 0x0000
+#define TIMER_FLAG_COUNTER 0x0002
+/* Stop or continue when overflowing/underflowing. */
+#define TIMER_FLAG_ONCE 0x0000
+#define TIMER_FLAG_CYCLIC 0x0004
+/* Count up or counter down. */
+#define TIMER_FLAG_UP 0x0000
+#define TIMER_FLAG_DOWN 0x0008
+/* Count on specific level or edge. */
+#define TIMER_FLAG_HIGH_LEVEL_SENSITIVE 0x0000
+#define TIMER_FLAG_LOW_LEVEL_SENSITIVE 0x0040
+#define TIMER_FLAG_RISE_EDGE 0x0010
+#define TIMER_FLAG_FALL_EDGE 0x0020
+#define TIMER_FLAG_ANY_EDGE 0x0030
+/* Signal is syncronous to module clock or not. */
+#define TIMER_FLAG_UNSYNC 0x0000
+#define TIMER_FLAG_SYNC 0x0080
+/* Different interrupt handle type. */
+#define TIMER_FLAG_NO_HANDLE 0x0000
+#if defined(__KERNEL__)
+ #define TIMER_FLAG_CALLBACK_IN_IRQ 0x0100
+#endif // defined(__KERNEL__)
+#define TIMER_FLAG_SIGNAL 0x0300
+/* Internal clock source or external clock source */
+#define TIMER_FLAG_INT_SRC 0x0000
+#define TIMER_FLAG_EXT_SRC 0x1000
+
+
+/*
+ * ioctl Command
+ */
+#define GPTU_REQUEST_TIMER 0x01 /* General method to setup timer/counter. */
+#define GPTU_FREE_TIMER 0x02 /* Free timer/counter. */
+#define GPTU_START_TIMER 0x03 /* Start or resume timer/counter. */
+#define GPTU_STOP_TIMER 0x04 /* Suspend timer/counter. */
+#define GPTU_GET_COUNT_VALUE 0x05 /* Get current count value. */
+#define GPTU_CALCULATE_DIVIDER 0x06 /* Calculate timer divider from given freq.*/
+#define GPTU_SET_TIMER 0x07 /* Simplified method to setup timer. */
+#define GPTU_SET_COUNTER 0x08 /* Simplified method to setup counter. */
+
+/*
+ * Data Type Used to Call ioctl
+ */
+struct gptu_ioctl_param {
+ unsigned int timer; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and *
+ * GPTU_SET_COUNTER, this field is ID of expected *
+ * timer/counter. If it's zero, a timer/counter would *
+ * be dynamically allocated and ID would be stored in *
+ * this field. *
+ * In command GPTU_GET_COUNT_VALUE, this field is *
+ * ignored. *
+ * In other command, this field is ID of timer/counter *
+ * allocated. */
+ unsigned int flag; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and *
+ * GPTU_SET_COUNTER, this field contains flags to *
+ * specify how to configure timer/counter. *
+ * In command GPTU_START_TIMER, zero indicate start *
+ * and non-zero indicate resume timer/counter. *
+ * In other command, this field is ignored. */
+ unsigned long value; /* In command GPTU_REQUEST_TIMER, this field contains *
+ * init/reload value. *
+ * In command GPTU_SET_TIMER, this field contains *
+ * frequency (0.001Hz) of timer. *
+ * In command GPTU_GET_COUNT_VALUE, current count *
+ * value would be stored in this field. *
+ * In command GPTU_CALCULATE_DIVIDER, this field *
+ * contains frequency wanted, and after calculation, *
+ * divider would be stored in this field to overwrite *
+ * the frequency. *
+ * In other command, this field is ignored. */
+ int pid; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, *
+ * if signal is required, this field contains process *
+ * ID to which signal would be sent. *
+ * In other command, this field is ignored. */
+ int sig; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, *
+ * if signal is required, this field contains signal *
+ * number which would be sent. *
+ * In other command, this field is ignored. */
+};
+
+/*
+ * ####################################
+ * Data Type
+ * ####################################
+ */
+typedef void (*timer_callback)(unsigned long arg);
+
+extern int ifxmips_request_timer(unsigned int, unsigned int, unsigned long, unsigned long, unsigned long);
+extern int ifxmips_free_timer(unsigned int);
+extern int ifxmips_start_timer(unsigned int, int);
+extern int ifxmips_stop_timer(unsigned int);
+extern int ifxmips_reset_counter_flags(u32 timer, u32 flags);
+extern int ifxmips_get_count_value(unsigned int, unsigned long *);
+extern u32 ifxmips_cal_divider(unsigned long);
+extern int ifxmips_set_timer(unsigned int, unsigned int, int, int, unsigned int, unsigned long, unsigned long);
+extern int ifxmips_set_counter(unsigned int timer, unsigned int flag,
+ u32 reload, unsigned long arg1, unsigned long arg2);
+
+#endif /* __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ */
projects / openwrt / svn-archive / archive.git / blobdiff