X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fsvn-archive%2Farchive.git;a=blobdiff_plain;f=target%2Flinux%2Fbrcm63xx%2Fpatches-3.9%2F511-board_V2500V.patch;fp=target%2Flinux%2Fbrcm63xx%2Fpatches-3.9%2F511-board_V2500V.patch;h=a2d78a6075b7bfbcc3bd5a16a718f81249ba19e4;hp=0000000000000000000000000000000000000000;hb=d71cd353dddfa9ace0d0a68e9496c92554c23a67;hpb=ebbd58becbddc08a5f3e14fb78c95a16e75a2f7f

diff --git a/target/linux/brcm63xx/patches-3.9/511-board_V2500V.patch b/target/linux/brcm63xx/patches-3.9/511-board_V2500V.patch
new file mode 100644
index 0000000000..a2d78a6075
--- /dev/null
+++ b/target/linux/brcm63xx/patches-3.9/511-board_V2500V.patch
@@ -0,0 +1,123 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -890,6 +890,65 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_V2500V_BB = {
++	.name				= "V2500V_BB",
++        .expected_cpu_id                = 0x6348,
++
++        .has_uart0                      = 1,
++        .has_enet0                      = 1,
++        .has_enet1                      = 1,
++        .has_pci                        = 1,
++
++        .enet0 = {
++                .has_phy                = 1,
++                .use_internal_phy       = 1,
++        },
++        .enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++                .force_speed_100        = 1,
++                .force_duplex_full      = 1,
++	},
++
++	.leds =	{
++		{
++			.name		= "V2500V_BB:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "V2500V_BB:red:power",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "V2500V_BB:green:adsl",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{	.name		= "V2500V_BB:green:ppp",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "V2500V_BB:green:wireless",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 31,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1950,6 +2009,7 @@ static const struct board_info __initcon
+ 	&board_96348_D4PW,
+ 	&board_spw500v,
+ 	&board_96348sv,
++	&board_V2500V_BB,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358
+@@ -2070,6 +2130,22 @@ void __init board_prom_init(void)
+ 		val &= MPI_CSBASE_BASE_MASK;
+ 	}
+ 	boot_addr = (u8 *)KSEG1ADDR(val);
++	printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
++
++	/* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
++	/* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
++	/* Loading firmware from the CFE Prompt always loads to Bank 0 */
++	/* Do an early check of CFE and then select bank 0 */
++
++	if (boot_addr == (u8 *)0xbf800000) {
++		u8 *tmp_boot_addr = (u8*)0xbfc00000;
++
++		bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
++		if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
++			printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
++			boot_addr = tmp_boot_addr;
++		}
++	}
+ 
+ 	/* dump cfe version */
+ 	cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -19,6 +19,7 @@
+ #include <linux/spi/spi.h>
+ #include <linux/spi/flash.h>
+ 
++#include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+ #include <bcm63xx_dev_flash.h>
+ #include <bcm63xx_dev_hsspi.h>
+@@ -157,6 +158,13 @@ int __init bcm63xx_flash_register(int nu
+ 		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+ 		val &= MPI_CSBASE_BASE_MASK;
+ 
++		/* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
++		/* Loading from CFE always uses Bank 0 */
++		if (!strcmp(board_get_name(), "V2500V_BB")) {
++			pr_info("V2500V: Start in Bank 0\n");
++			val = val + 0x400000; // Select Bank 0 start address
++		}
++
+ 		mtd_resources[0].start = val;
+ 		mtd_resources[0].end = 0x1FFFFFFF;
+