applications/luci-app-olsr/po/zh-tw/olsr.po

   1 msgid ""
   2 msgstr ""
   3 "Project-Id-Version: PACKAGE VERSION\n"
   4 "PO-Revision-Date: 2014-05-15 07:15+0200\n"
   5 "Last-Translator: omnistack <omnistack@gmail.com>\n"
   6 "Language-Team: none\n"
   7 "Language: zh_TW\n"
   8 "MIME-Version: 1.0\n"
   9 "Content-Type: text/plain; charset=UTF-8\n"
  10 "Content-Transfer-Encoding: 8bit\n"
  11 "Plural-Forms: nplurals=1; plural=0;\n"
  12 "X-Generator: Pootle 2.0.6\n"
  13
  14 msgid "Active MID announcements"
  15 msgstr "啟用Mesh網狀網路ID公告"
  16
  17 msgid "Active OLSR nodes"
  18 msgstr "啟用OLSR路由協議節點"
  19
  20 msgid "Active host net announcements"
  21 msgstr "啟用主機網路公告"
  22
  23 msgid "Advanced Settings"
  24 msgstr "進階設定"
  25
  26 msgid "Allow gateways with NAT"
  27 msgstr "允許帶NAT的匝道器"
  28
  29 msgid "Allow the selection of an outgoing ipv4 gateway with NAT"
  30 msgstr "允許帶NAT的匝道器選擇輸出ipv4封包"
  31
  32 msgid "Announce uplink"
  33 msgstr "公告上傳"
  34
  35 msgid "Announced network"
  36 msgstr "公告網路"
  37
  38 msgid "Bad (ETX > 10)"
  39 msgstr ""
  40
  41 msgid "Bad (SNR < 5)"
  42 msgstr ""
  43
  44 msgid "Both values must use the dotted decimal notation."
  45 msgstr "這兩個值都必須採用點分十進位制格式"
  46
  47 msgid "Broadcast address"
  48 msgstr "廣播位址"
  49
  50 msgid "Can only be a valid IPv4 or IPv6 address or 'default'"
  51 msgstr ""
  52
  53 msgid "Can only be a valid IPv6 address or 'default'"
  54 msgstr ""
  55
  56 msgid "Configuration"
  57 msgstr "設定"
  58
  59 msgid ""
  60 "Could not get any data. Make sure the jsoninfo plugin is installed and "
  61 "allows connections from localhost."
  62 msgstr ""
  63
  64 msgid "Device"
  65 msgstr "設備"
  66
  67 msgid "Display"
  68 msgstr "顯示"
  69
  70 msgid "Downlink"
  71 msgstr "下行"
  72
  73 msgid "Download Config"
  74 msgstr "下載設置"
  75
  76 msgid "ETX"
  77 msgstr ""
  78
  79 msgid "Enable"
  80 msgstr "啟用"
  81
  82 msgid ""
  83 "Enable SmartGateway. If it is disabled, then all other SmartGateway "
  84 "parameters are ignored. Default is \"no\"."
  85 msgstr ""
  86 "啟用機動式匝道器. 假如它失效, 其它所有機動式匝道器參數將被忽視. 預設值是\"no"
  87 "\""
  88
  89 msgid "Enable this interface."
  90 msgstr "啟用這個介面"
  91
  92 msgid "Enabled"
  93 msgstr "啟用"
  94
  95 msgid "Expected retransmission count"
  96 msgstr "預計重傳次數"
  97
  98 msgid "FIB metric"
  99 msgstr "FIB指標"
 100
 101 msgid ""
 102 "FIBMetric controls the metric value of the host-routes OLSRd sets. \"flat\" "
 103 "means that the metric value is always 2. This is the preferred value because "
 104 "it helps the linux kernel routing to clean up older routes. \"correct\" uses "
 105 "the hopcount as the metric value. \"approx\" use the hopcount as the metric "
 106 "value too, but does only update the hopcount if the nexthop changes too. "
 107 "Default is \"flat\"."
 108 msgstr ""
 109 "FIBMetric控制OLSR主機路由的公用路由計量設定.  \"flat\" 代表是公用計量數永遠是"
 110 "2. 這是較受歡迎的數值, 因為它會協助linux核心路由清除舊的路由表. \"correct\"使"
 111 "用跳躍數當作公用路由計量. \"approx\"也使用跳躍數當作公用路由計量, 但只作用在"
 112 "跳躍數也更新時. 預設值是\"flat\"."
 113
 114 msgid "Fisheye mechanism for TCs (checked means on). Default is \"on\""
 115 msgstr ""
 116
 117 msgid "Gateway"
 118 msgstr "匝道器"
 119
 120 msgid "General Settings"
 121 msgstr "一般設定"
 122
 123 msgid "General settings"
 124 msgstr "一般設定"
 125
 126 msgid "Good (2 < ETX < 4)"
 127 msgstr ""
 128
 129 msgid "Good (30 > SNR > 20)"
 130 msgstr ""
 131
 132 msgid "Green"
 133 msgstr ""
 134
 135 msgid "HNA"
 136 msgstr ""
 137
 138 msgid "HNA Announcements"
 139 msgstr ""
 140
 141 msgid "HNA interval"
 142 msgstr ""
 143
 144 msgid "HNA validity time"
 145 msgstr ""
 146
 147 #, fuzzy
 148 msgid "HNA6 Announcements"
 149 msgstr "啟用Mesh網狀網路ID公告"
 150
 151 msgid "Hello"
 152 msgstr ""
 153
 154 msgid "Hello interval"
 155 msgstr ""
 156
 157 msgid "Hello validity time"
 158 msgstr ""
 159
 160 msgid "Hide IPv4"
 161 msgstr ""
 162
 163 msgid "Hide IPv6"
 164 msgstr ""
 165
 166 msgid "Hna4"
 167 msgstr ""
 168
 169 msgid "Hna6"
 170 msgstr ""
 171
 172 msgid "Hops"
 173 msgstr ""
 174
 175 msgid "Hostname"
 176 msgstr ""
 177
 178 msgid ""
 179 "Hosts in a OLSR routed network can announce connecitivity to external "
 180 "networks using HNA messages."
 181 msgstr ""
 182
 183 msgid ""
 184 "Hosts in a OLSR routed network can announce connecitivity to external "
 185 "networks using HNA6 messages."
 186 msgstr ""
 187
 188 msgid ""
 189 "Hysteresis for link sensing (only for hopcount metric). Hysteresis adds more "
 190 "robustness to the link sensing but delays neighbor registration. Defaults is "
 191 "\"yes\""
 192 msgstr ""
 193
 194 msgid "IP Addresses"
 195 msgstr ""
 196
 197 msgid ""
 198 "IP-version to use. If 6and4 is selected then one olsrd instance is started "
 199 "for each protocol."
 200 msgstr ""
 201
 202 msgid "IPv4"
 203 msgstr ""
 204
 205 msgid "IPv4 broadcast"
 206 msgstr ""
 207
 208 msgid ""
 209 "IPv4 broadcast address for outgoing OLSR packets. One useful example would "
 210 "be 255.255.255.255. Default is \"0.0.0.0\", which triggers the usage of the "
 211 "interface broadcast IP."
 212 msgstr ""
 213
 214 msgid "IPv4 source"
 215 msgstr ""
 216
 217 msgid ""
 218 "IPv4 src address for outgoing OLSR packages. Default is \"0.0.0.0\", which "
 219 "triggers usage of the interface IP."
 220 msgstr ""
 221
 222 msgid "IPv6"
 223 msgstr ""
 224
 225 msgid "IPv6 multicast"
 226 msgstr ""
 227
 228 msgid ""
 229 "IPv6 multicast address. Default is \"FF02::6D\", the manet-router linklocal "
 230 "multicast."
 231 msgstr ""
 232
 233 msgid ""
 234 "IPv6 network must be given in full notation, prefix must be in CIDR notation."
 235 msgstr ""
 236
 237 msgid "IPv6 source"
 238 msgstr ""
 239
 240 msgid ""
 241 "IPv6 src prefix. OLSRd will choose one of the interface IPs which matches "
 242 "the prefix of this parameter. Default is \"0::/0\", which triggers the usage "
 243 "of a not-linklocal interface IP."
 244 msgstr ""
 245
 246 msgid "IPv6-Prefix of the uplink"
 247 msgstr ""
 248
 249 msgid ""
 250 "If the route to the current gateway is to be changed, the ETX value of this "
 251 "gateway is multiplied with this value before it is compared to the new one. "
 252 "The parameter can be a value between 0.1 and 1.0, but should be close to 1.0 "
 253 "if changed.<br /><b>WARNING:</b> This parameter should not be used together "
 254 "with the etx_ffeth metric!<br />Defaults to \"1.0\"."
 255 msgstr ""
 256
 257 msgid ""
 258 "If this Node uses NAT for connections to the internet. Default is \"yes\"."
 259 msgstr ""
 260
 261 msgid "Interface"
 262 msgstr ""
 263
 264 msgid ""
 265 "Interface Mode is used to prevent unnecessary packet forwarding on switched "
 266 "ethernet interfaces. valid Modes are \"mesh\" and \"ether\". Default is "
 267 "\"mesh\"."
 268 msgstr ""
 269
 270 msgid "Interfaces"
 271 msgstr ""
 272
 273 msgid "Interfaces Defaults"
 274 msgstr ""
 275
 276 msgid "Internet protocol"
 277 msgstr ""
 278
 279 msgid ""
 280 "Interval to poll network interfaces for configuration changes (in seconds). "
 281 "Default is \"2.5\"."
 282 msgstr ""
 283
 284 msgid "Invalid Value for LQMult-Value. Must be between 0.01 and 1.0."
 285 msgstr ""
 286
 287 msgid ""
 288 "Invalid Value for LQMult-Value. You must use a decimal number between 0.01 "
 289 "and 1.0 here."
 290 msgstr ""
 291
 292 msgid "Known OLSR routes"
 293 msgstr ""
 294
 295 msgid "LQ"
 296 msgstr ""
 297
 298 msgid "LQ aging"
 299 msgstr ""
 300
 301 msgid "LQ algorithm"
 302 msgstr ""
 303
 304 msgid "LQ fisheye"
 305 msgstr ""
 306
 307 msgid "LQ level"
 308 msgstr ""
 309
 310 msgid ""
 311 "LQMult requires two values (IP address or 'default' and multiplicator) "
 312 "seperated by space."
 313 msgstr ""
 314
 315 msgid "Last hop"
 316 msgstr ""
 317
 318 msgid "Legend"
 319 msgstr ""
 320
 321 msgid "Library"
 322 msgstr ""
 323
 324 msgid "Link Quality Settings"
 325 msgstr ""
 326
 327 msgid ""
 328 "Link quality aging factor (only for lq level 2). Tuning parameter for "
 329 "etx_float and etx_fpm, smaller values mean slower changes of ETX value. "
 330 "(allowed values are between 0.01 and 1.0)"
 331 msgstr ""
 332
 333 msgid ""
 334 "Link quality algorithm (only for lq level 2).<br /><b>etx_float</b>: "
 335 "floating point ETX with exponential aging<br /><b>etx_fpm</b> : same as "
 336 "etx_float, but with integer arithmetic<br /><b>etx_ff</b> : ETX freifunk, an "
 337 "etx variant which use all OLSR traffic (instead of only hellos) for ETX "
 338 "calculation<br /><b>etx_ffeth</b>: incompatible variant of etx_ff that "
 339 "allows ethernet links with ETX 0.1.<br />Defaults to \"etx_ff\""
 340 msgstr ""
 341
 342 msgid ""
 343 "Link quality level switch between hopcount and cost-based (mostly ETX) "
 344 "routing.<br /><b>0</b> = do not use link quality<br /><b>2</b> = use link "
 345 "quality for MPR selection and routing<br />Default is \"2\""
 346 msgstr ""
 347
 348 msgid "LinkQuality Multiplicator"
 349 msgstr ""
 350
 351 msgid "Links per node (average)"
 352 msgstr ""
 353
 354 msgid "Links total"
 355 msgstr ""
 356
 357 msgid "Local interface IP"
 358 msgstr ""
 359
 360 msgid "MID"
 361 msgstr ""
 362
 363 msgid "MID interval"
 364 msgstr ""
 365
 366 msgid "MID validity time"
 367 msgstr ""
 368
 369 msgid "MTU"
 370 msgstr ""
 371
 372 msgid "Main IP"
 373 msgstr ""
 374
 375 msgid ""
 376 "Make sure that OLSRd is running, the \"jsoninfo\" plugin is loaded, "
 377 "configured on port 9090 and accepts connections from \"127.0.0.1\"."
 378 msgstr ""
 379
 380 msgid "Metric"
 381 msgstr ""
 382
 383 msgid "Mode"
 384 msgstr ""
 385
 386 msgid ""
 387 "Multiply routes with the factor given here. Allowed values are between 0.01 "
 388 "and 1.0. It is only used when LQ-Level is greater than 0. Examples:<br /"
 389 ">reduce LQ to 192.168.0.1 by half: 192.168.0.1 0.5<br />reduce LQ to all "
 390 "nodes on this interface by 20%: default 0.8"
 391 msgstr ""
 392
 393 msgid ""
 394 "Multiply routes with the factor given here. Allowed values are between 0.01 "
 395 "and 1.0. It is only used when LQ-Level is greater than 0. Examples:<br /"
 396 ">reduce LQ to fd91:662e:3c58::1 by half: fd91:662e:3c58::1 0.5<br />reduce "
 397 "LQ to all nodes on this interface by 20%: default 0.8"
 398 msgstr ""
 399
 400 msgid "NAT threshold"
 401 msgstr ""
 402
 403 msgid "NLQ"
 404 msgstr ""
 405
 406 msgid "Neighbors"
 407 msgstr ""
 408
 409 msgid "Neighbour IP"
 410 msgstr ""
 411
 412 msgid "Neighbours"
 413 msgstr ""
 414
 415 msgid "Netmask"
 416 msgstr ""
 417
 418 msgid "Network"
 419 msgstr ""
 420
 421 msgid "Network address"
 422 msgstr ""
 423
 424 msgid "Nic changes poll interval"
 425 msgstr ""
 426
 427 msgid "Nodes"
 428 msgstr ""
 429
 430 msgid "OLSR"
 431 msgstr ""
 432
 433 msgid "OLSR - Display Options"
 434 msgstr ""
 435
 436 msgid "OLSR - HNA-Announcements"
 437 msgstr ""
 438
 439 msgid "OLSR - HNA6-Announcements"
 440 msgstr ""
 441
 442 msgid "OLSR - Plugins"
 443 msgstr ""
 444
 445 msgid "OLSR Daemon"
 446 msgstr ""
 447
 448 msgid "OLSR Daemon - Interface"
 449 msgstr ""
 450
 451 msgid "OLSR connections"
 452 msgstr ""
 453
 454 msgid "OLSR gateway"
 455 msgstr ""
 456
 457 msgid "OLSR node"
 458 msgstr ""
 459
 460 msgid "Orange"
 461 msgstr ""
 462
 463 msgid "Overview"
 464 msgstr ""
 465
 466 msgid "Overview of currently active OLSR host net announcements"
 467 msgstr ""
 468
 469 msgid "Overview of currently established OLSR connections"
 470 msgstr ""
 471
 472 msgid "Overview of currently known OLSR nodes"
 473 msgstr ""
 474
 475 msgid "Overview of currently known routes to other OLSR nodes"
 476 msgstr ""
 477
 478 msgid "Overview of interfaces where OLSR is running"
 479 msgstr ""
 480
 481 msgid "Overview of known multiple interface announcements"
 482 msgstr ""
 483
 484 msgid "Overview of smart gateways in this network"
 485 msgstr ""
 486
 487 msgid "Plugin configuration"
 488 msgstr ""
 489
 490 msgid "Plugins"
 491 msgstr ""
 492
 493 msgid "Polling rate for OLSR sockets in seconds. Default is 0.05."
 494 msgstr ""
 495
 496 msgid "Pollrate"
 497 msgstr ""
 498
 499 msgid "Port"
 500 msgstr ""
 501
 502 msgid "Prefix"
 503 msgstr ""
 504
 505 msgid "Red"
 506 msgstr ""
 507
 508 msgid "Resolve"
 509 msgstr ""
 510
 511 msgid ""
 512 "Resolve hostnames on status pages. It is generally safe to allow this, but "
 513 "if you use public IPs and have unstable DNS-Setup then those pages will load "
 514 "really slow. In this case disable it here."
 515 msgstr ""
 516
 517 msgid "Routes"
 518 msgstr ""
 519
 520 msgid "Secondary OLSR interfaces"
 521 msgstr ""
 522
 523 msgid "Selected"
 524 msgstr ""
 525
 526 msgid ""
 527 "Sets the main IP (originator ip) of the router. This IP will NEVER change "
 528 "during the uptime of olsrd. Default is 0.0.0.0, which triggers usage of the "
 529 "IP of the first interface."
 530 msgstr ""
 531
 532 msgid ""
 533 "Sets the main IP (originator ip) of the router. This IP will NEVER change "
 534 "during the uptime of olsrd. Default is ::, which triggers usage of the IP of "
 535 "the first interface."
 536 msgstr ""
 537
 538 msgid "Show IPv4"
 539 msgstr ""
 540
 541 msgid "Show IPv6"
 542 msgstr ""
 543
 544 msgid "Signal Noise Ratio in dB"
 545 msgstr ""
 546
 547 msgid "SmartGW"
 548 msgstr ""
 549
 550 msgid "SmartGW announcements"
 551 msgstr ""
 552
 553 msgid "SmartGateway is not configured on this system."
 554 msgstr ""
 555
 556 msgid "Source address"
 557 msgstr ""
 558
 559 msgid ""
 560 "Specifies the speed of the uplink in kilobits/s. First parameter is "
 561 "upstream, second parameter is downstream. Default is \"128 1024\"."
 562 msgstr ""
 563
 564 msgid "Speed of the uplink"
 565 msgstr ""
 566
 567 msgid "State"
 568 msgstr ""
 569
 570 msgid "Still usable (20 > SNR > 5)"
 571 msgstr ""
 572
 573 msgid "Still usable (4 < ETX < 10)"
 574 msgstr ""
 575
 576 msgid "Success rate of packages received from the neighbour"
 577 msgstr ""
 578
 579 msgid "Success rate of packages sent to the neighbour"
 580 msgstr ""
 581
 582 msgid "TC"
 583 msgstr ""
 584
 585 msgid "TC interval"
 586 msgstr ""
 587
 588 msgid "TC validity time"
 589 msgstr ""
 590
 591 msgid "TOS value"
 592 msgstr ""
 593
 594 msgid ""
 595 "The OLSR daemon is an implementation of the Optimized Link State Routing "
 596 "protocol. As such it allows mesh routing for any network equipment. It runs "
 597 "on any wifi card that supports ad-hoc mode and of course on any ethernet "
 598 "device. Visit <a href='http://www.olsr.org'>olsrd.org</a> for help and "
 599 "documentation."
 600 msgstr ""
 601
 602 msgid ""
 603 "The fixed willingness to use. If not set willingness will be calculated "
 604 "dynamically based on battery/power status. Default is \"3\"."
 605 msgstr ""
 606
 607 msgid "The interface OLSRd should serve."
 608 msgstr ""
 609
 610 msgid ""
 611 "The port OLSR uses. This should usually stay at the IANA assigned port 698. "
 612 "It can have a value between 1 and 65535."
 613 msgstr ""
 614
 615 msgid ""
 616 "This can be used to signal the external IPv6 prefix of the uplink to the "
 617 "clients. This might allow a client to change it's local IPv6 address to use "
 618 "the IPv6 gateway without any kind of address translation. The maximum prefix "
 619 "length is 64 bits. Default is \"::/0\" (no prefix)."
 620 msgstr ""
 621
 622 msgid "Timing and Validity"
 623 msgstr ""
 624
 625 msgid "Topology"
 626 msgstr ""
 627
 628 msgid ""
 629 "Type of service value for the IP header of control traffic. Default is "
 630 "\"16\"."
 631 msgstr ""
 632
 633 msgid "Unable to connect to the OLSR daemon!"
 634 msgstr ""
 635
 636 msgid "Uplink"
 637 msgstr ""
 638
 639 msgid "Uplink uses NAT"
 640 msgstr ""
 641
 642 msgid "Use hysteresis"
 643 msgstr ""
 644
 645 msgid "Validity Time"
 646 msgstr ""
 647
 648 msgid "Version"
 649 msgstr ""
 650
 651 msgid "Very good (ETX < 2)"
 652 msgstr ""
 653
 654 msgid "Very good (SNR > 30)"
 655 msgstr ""
 656
 657 msgid "WLAN"
 658 msgstr ""
 659
 660 msgid ""
 661 "Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not "
 662 "work, please install it."
 663 msgstr ""
 664
 665 msgid "Weight"
 666 msgstr ""
 667
 668 msgid ""
 669 "When multiple links exist between hosts the weight of interface is used to "
 670 "determine the link to use. Normally the weight is automatically calculated "
 671 "by olsrd based on the characteristics of the interface, but here you can "
 672 "specify a fixed value. Olsrd will choose links with the lowest value.<br /"
 673 "><b>Note:</b> Interface weight is used only when LinkQualityLevel is set to "
 674 "0. For any other value of LinkQualityLevel, the interface ETX value is used "
 675 "instead."
 676 msgstr ""
 677
 678 msgid ""
 679 "Which kind of uplink is exported to the other mesh nodes. An uplink is "
 680 "detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. "
 681 "Default setting is \"both\"."
 682 msgstr ""
 683
 684 msgid ""
 685 "Which kind of uplink is exported to the other mesh nodes. An uplink is "
 686 "detected by looking for a local HNA6 ::ffff:0:0/96 or 2000::/3. Default "
 687 "setting is \"both\"."
 688 msgstr ""
 689
 690 msgid "Willingness"
 691 msgstr ""
 692
 693 msgid "Yellow"
 694 msgstr ""
 695
 696 msgid "down"
 697 msgstr ""
 698
 699 msgid "infinate"
 700 msgstr ""
 701
 702 msgid "no"
 703 msgstr ""
 704
 705 msgid "up"
 706 msgstr ""
 707
 708 msgid "yes"
 709 msgstr ""