drivers/net/phy/Kconfig

   1
   2 config BITBANGMII
   3         bool "Bit-banged ethernet MII management channel support"
   4
   5 config MV88E6352_SWITCH
   6         bool "Marvell 88E6352 switch support"
   7
   8 menuconfig PHYLIB
   9         bool "Ethernet PHY (physical media interface) support"
  10         help
  11           Enable Ethernet PHY (physical media interface) support.
  12
  13 if PHYLIB
  14
  15 config MV88E61XX_SWITCH
  16         bool "Marvel MV88E61xx Ethernet switch PHY support."
  17
  18 if MV88E61XX_SWITCH
  19
  20 config MV88E61XX_CPU_PORT
  21         int "CPU Port"
  22
  23 config MV88E61XX_PHY_PORTS
  24         hex "Bitmask of PHY Ports"
  25
  26 config MV88E61XX_FIXED_PORTS
  27         hex "Bitmask of PHYless serdes Ports"
  28
  29 endif # MV88E61XX_SWITCH
  30
  31 config PHYLIB_10G
  32         bool "Generic 10G PHY support"
  33
  34 config PHY_AQUANTIA
  35         bool "Aquantia Ethernet PHYs support"
  36
  37 config PHY_ATHEROS
  38         bool "Atheros Ethernet PHYs support"
  39
  40 config PHY_BROADCOM
  41         bool "Broadcom Ethernet PHYs support"
  42
  43 config PHY_CORTINA
  44         bool "Cortina Ethernet PHYs support"
  45
  46 config PHY_DAVICOM
  47         bool "Davicom Ethernet PHYs support"
  48
  49 config PHY_ET1011C
  50         bool "LSI TruePHY ET1011C support"
  51
  52 config PHY_LXT
  53         bool "LXT971 Ethernet PHY support"
  54
  55 config PHY_MARVELL
  56         bool "Marvell Ethernet PHYs support"
  57
  58 config PHY_MICREL
  59         bool "Micrel Ethernet PHYs support"
  60         help
  61           Enable support for the GbE PHYs manufactured by Micrel (now
  62           a part of Microchip). This includes drivers for the KSZ804,
  63           KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, KSZ8721
  64           either/or KSZ9021 (see the "Micrel KSZ9021 family support"
  65           config option for details), and KSZ9031 (if configured).
  66
  67 if PHY_MICREL
  68
  69 config PHY_MICREL_KSZ9021
  70         bool "Micrel KSZ9021 family support"
  71         select PHY_GIGE
  72         help
  73           Enable support for the Micrel KSZ9021 GbE PHY family.  If
  74           enabled, the extended register read/write for KSZ9021 PHYs
  75           is supported through the 'mdio' command and any RGMII signal
  76           delays configured in the device tree will be applied to the
  77           PHY during initialisation.
  78
  79           Note that the KSZ9021 uses the same part number os the
  80           KSZ8921BL, so enabling this option disables support for the
  81           KSZ8721BL.
  82
  83 config PHY_MICREL_KSZ9031
  84         bool "Micrel KSZ9031 family support"
  85         select PHY_GIGE
  86         help
  87           Enable support for the Micrel KSZ9031 GbE PHY family.  If
  88           enabled, the extended register read/write for KSZ9021 PHYs
  89           is supported through the 'mdio' command and any RGMII signal
  90           delays configured in the device tree will be applied to the
  91           PHY during initialisatioin.
  92
  93 endif # PHY_MICREL
  94
  95 config PHY_MSCC
  96         bool "Microsemi Corp Ethernet PHYs support"
  97
  98 config PHY_NATSEMI
  99         bool "National Semiconductor Ethernet PHYs support"
 100
 101 config PHY_REALTEK
 102         bool "Realtek Ethernet PHYs support"
 103
 104 config RTL8211X_PHY_FORCE_MASTER
 105         bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
 106         depends on PHY_REALTEK
 107         help
 108           Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
 109           This can work around link stability and data corruption issues on gigabit
 110           links which can occur in slave mode on certain PHYs, e.g. on the
 111           RTL8211C(L).
 112
 113           Please note that two directly connected devices (i.e. via crossover cable)
 114           will not be able to establish a link between each other if they both force
 115           master mode. Multiple devices forcing master mode when connected by a
 116           network switch do not pose a problem as the switch configures its affected
 117           ports into slave mode.
 118
 119           This option only affects gigabit links. If you must establish a direct
 120           connection between two devices which both force master mode, try forcing
 121           the link speed to 100MBit/s.
 122
 123           If unsure, say N.
 124
 125 config PHY_SMSC
 126         bool  "Microchip(SMSC) Ethernet PHYs support"
 127
 128 config PHY_TERANETICS
 129         bool "Teranetics Ethernet PHYs support"
 130
 131 config PHY_TI
 132         bool "Texas Instruments Ethernet PHYs support"
 133
 134 config PHY_VITESSE
 135         bool "Vitesse Ethernet PHYs support"
 136
 137 config PHY_XILINX
 138         bool "Xilinx Ethernet PHYs support"
 139
 140 config PHY_FIXED
 141         bool "Fixed-Link PHY"
 142         depends on DM_ETH
 143         help
 144           Fixed PHY is used for having a 'fixed-link' to another MAC with a direct
 145           connection (MII, RGMII, ...).
 146           There is nothing like autoneogation and so
 147           on, the link is always up with fixed speed and fixed duplex-setting.
 148           More information: doc/device-tree-bindings/net/fixed-link.txt
 149
 150 endif #PHYLIB