target/linux/ath79/dts/ar9330_glinet_ar150.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9330.dtsi"
   8
   9 / {
  10         model = "GL.iNet GL-AR150";
  11         compatible = "glinet,ar150", "qca,ar9330";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-status = &wlan;
  16         };
  17
  18         leds {
  19                 compatible = "gpio-leds";
  20
  21                 wlan: wlan {
  22                         label = "gl-ar150:orange:wlan";
  23                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  24                         default-state = "off";
  25                         linux,default-trigger = "phy0tpt";
  26                 };
  27
  28                 lan {
  29                         label = "gl-ar150:green:lan";
  30                         gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
  31                         default-state = "off";
  32                 };
  33
  34                 wan {
  35                         label = "gl-ar150:green:wan";
  36                         gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
  37                         default-state = "off";
  38                 };
  39         };
  40
  41         keys {
  42                 compatible = "gpio-keys-polled";
  43                 poll-interval = <100>;
  44
  45                 manual {
  46                         label = "manual";
  47                         linux,code = <BTN_7>;
  48                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  49                 };
  50
  51                 auto {
  52                         label = "auto";
  53                         linux,code = <BTN_8>;
  54                         gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
  55                 };
  56
  57                 reset {
  58                         label = "reset";
  59                         linux,code = <KEY_RESTART>;
  60                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  61                 };
  62         };
  63 };
  64
  65 &uart {
  66         status = "okay";
  67 };
  68
  69 &gpio {
  70         status = "okay";
  71 };
  72
  73 &usb {
  74         dr_mode = "host";
  75         status = "okay";
  76 };
  77
  78 &usb_phy {
  79         status = "okay";
  80         gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
  81 };
  82
  83 &spi {
  84         num-chipselects = <1>;
  85         status = "okay";
  86
  87         flash@0 {
  88                 compatible = "jedec,spi-nor";
  89                 spi-max-frequency = <104000000>;
  90                 reg = <0>;
  91
  92                 partitions {
  93                         compatible = "fixed-partitions";
  94                         #address-cells = <1>;
  95                         #size-cells = <1>;
  96
  97                         partition@0 {
  98                                 label = "u-boot";
  99                                 reg = <0x000000 0x040000>;
 100                                 read-only;
 101                         };
 102
 103                         partition@1 {
 104                                 label = "u-boot-env";
 105                                 reg = <0x040000 0x010000>;
 106                         };
 107
 108                         partition@2 {
 109                                 label = "firmware";
 110                                 reg = <0x050000 0xfa0000>;
 111                         };
 112
 113                         art: partition@3 {
 114                                 label = "ART";
 115                                 reg = <0xff0000 0x010000>;
 116                                 read-only;
 117                         };
 118                 };
 119         };
 120 };
 121
 122 &eth0 {
 123         status = "okay";
 124
 125         mtd-mac-address = <&art 0x0>;
 126 };
 127
 128 &eth1 {
 129         status = "okay";
 130
 131         mtd-mac-address = <&art 0x0>;
 132
 133         gmac-config {
 134                 device = <&gmac>;
 135
 136                 switch-phy-addr-swap = <0>;
 137                 switch-phy-swap = <0>;
 138         };
 139 };
 140
 141 &wmac {
 142         status = "okay";
 143         mtd-cal-data = <&art 0x1000>;
 144         mtd-mac-address = <&art 0x0>;
 145 };