target/linux/ath79/dts/qca9531_comfast_cf-e5.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca953x.dtsi"
   8
   9 / {
  10         compatible = "comfast,cf-e5", "qca,qca9531";
  11         model = "COMFAST CF-E5/E7";
  12
  13         aliases {
  14                 label-mac-device = &eth0;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys-polled";
  19                 poll-interval = <20>;
  20
  21                 button0 {
  22                         label = "reset";
  23                         linux,code = <KEY_RESTART>;
  24                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  25                 };
  26         };
  27
  28         leds {
  29                 compatible = "gpio-leds";
  30                 pinctrl-names = "default";
  31                 pinctrl-0 = <&jtag_disable_pins &led_wan_pin>;
  32
  33                 wan {
  34                         label = "cf-e5:blue:wan";
  35                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  36                 };
  37
  38                 lan {
  39                         label = "cf-e5:blue:lan";
  40                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  41                 };
  42
  43                 wlan {
  44                         label = "cf-e5:blue:wlan";
  45                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  46                         linux,default-trigger = "phy0tpt";
  47                 };
  48
  49                 rssi0 {
  50                         label = "cf-e5:blue:rssi0";
  51                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  52                 };
  53
  54                 rssi1 {
  55                         label = "cf-e5:blue:rssi1";
  56                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  57                 };
  58
  59                 rssi2 {
  60                         label = "cf-e5:blue:rssi2";
  61                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  62                 };
  63         };
  64 };
  65
  66 &uart {
  67         status = "okay";
  68 };
  69
  70 &usb0 {
  71         #address-cells = <1>;
  72         #size-cells = <0>;
  73         status = "okay";
  74
  75         hub_port: port@1 {
  76                 reg = <1>;
  77                 #trigger-source-cells = <0>;
  78         };
  79 };
  80
  81 &usb_phy {
  82         status = "okay";
  83 };
  84
  85 &spi {
  86         status = "okay";
  87         num-cs = <1>;
  88
  89         flash@0 {
  90                 compatible = "jedec,spi-nor";
  91                 reg = <0>;
  92                 spi-max-frequency = <25000000>;
  93
  94                 partitions {
  95                         compatible = "fixed-partitions";
  96                         #address-cells = <1>;
  97                         #size-cells = <1>;
  98
  99                         partition@0 {
 100                                 label = "u-boot";
 101                                 reg = <0x000000 0x010000>;
 102                                 read-only;
 103                         };
 104
 105                         art: partition@10000 {
 106                                 label = "art";
 107                                 reg = <0x010000 0x010000>;
 108                                 read-only;
 109                         };
 110
 111                         partition@20000 {
 112                                 compatible = "denx,uimage";
 113                                 label = "firmware";
 114                                 reg = <0x020000 0xfd0000>;
 115                         };
 116
 117                         partition@ff0000 {
 118                                 label = "art-backup";
 119                                 reg = <0xff0000 0x010000>;
 120                                 read-only;
 121                         };
 122                 };
 123         };
 124 };
 125
 126 &eth0 {
 127         status = "okay";
 128         mtd-mac-address = <&art 0x0>;
 129         phy-handle = <&swphy4>;
 130 };
 131
 132 &eth1 {
 133         mtd-mac-address = <&art 0x6>;
 134 };
 135
 136 &wmac {
 137         status = "okay";
 138         mtd-cal-data = <&art 0x1000>;
 139 };
 140
 141 &pinmux {
 142         led_wan_pin: pinmux_led_wan_pin {
 143                 pinctrl-single,bits = <0x4 0x0 0xff>;
 144         };
 145 };