target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca953x.dtsi"
   8
   9 / {
  10         compatible = "glinet,gl-ar750", "qca,qca9531";
  11         model = "GL.iNet GL-AR750";
  12
  13         aliases {
  14                 label-mac-device = &eth0;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys";
  19
  20                 pinctrl-names = "default";
  21                 pinctrl-0 = <&jtag_disable_pins>;
  22
  23                 reset {
  24                         label = "reset";
  25                         linux,code = <KEY_RESTART>;
  26                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 mode {
  30                         label = "mode";
  31                         linux,code = <BTN_0>;
  32                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  33                 };
  34         };
  35
  36         leds {
  37                 compatible = "gpio-leds";
  38
  39                 power {
  40                         label = "gl-ar750:white:power";
  41                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  42                         default-state = "on";
  43                 };
  44
  45                 wlan2g {
  46                         label = "gl-ar750:white:wlan2g";
  47                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  48                         linux,default-trigger = "phy1tpt";
  49                 };
  50
  51                 wlan5g {
  52                         label = "gl-ar750:white:wlan5g";
  53                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  54                         linux,default-trigger = "phy0tpt";
  55                 };
  56
  57         };
  58
  59         i2c {
  60                 compatible = "i2c-gpio";
  61
  62                 sda-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  63                 scl-gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  64         };
  65
  66
  67 };
  68
  69 &pcie0 {
  70         status = "okay";
  71
  72         wifi@0,0 {
  73                 compatible = "qcom,ath10k";
  74                 reg = <0 0 0 0 0>;
  75                 device_type = "pci";
  76         };
  77 };
  78
  79 &uart {
  80         status = "okay";
  81 };
  82
  83 &usb0 {
  84         status = "okay";
  85 };
  86
  87 &usb_phy {
  88         status = "okay";
  89 };
  90
  91 &spi {
  92         status = "okay";
  93         num-cs = <0>;
  94
  95         flash@0 {
  96                 compatible = "jedec,spi-nor";
  97                 reg = <0>;
  98                 spi-max-frequency = <25000000>;
  99
 100                 partitions {
 101                         compatible = "fixed-partitions";
 102                         #address-cells = <1>;
 103                         #size-cells = <1>;
 104
 105                         partition@0 {
 106                                 label = "u-boot";
 107                                 reg = <0x000000 0x040000>;
 108                                 read-only;
 109                         };
 110
 111                         partition@40000 {
 112                                 label = "u-boot-env";
 113                                 reg = <0x040000 0x010000>;
 114                                 read-only;
 115                         };
 116
 117                         art: partition@50000 {
 118                                 label = "art";
 119                                 reg = <0x050000 0x010000>;
 120                                 read-only;
 121                         };
 122
 123                         partition@60000 {
 124                                 compatible = "denx,uimage";
 125                                 label = "firmware";
 126                                 reg = <0x060000 0xfa0000>;
 127                         };
 128                 };
 129         };
 130 };
 131
 132 &eth0 {
 133         status = "okay";
 134         mtd-mac-address = <&art 0x0>;
 135         phy-handle = <&swphy4>;
 136 };
 137
 138 &eth1 {
 139         mtd-mac-address = <&art 0x0>;
 140         mtd-mac-address-increment = <1>;
 141 };
 142
 143 &wmac {
 144         status = "okay";
 145         mtd-cal-data = <&art 0x1000>;
 146 };