target/linux/ath79/dts/qca9558_tplink_tl-wdr4900-v2.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca955x.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "tplink,tl-wdr4900-v2", "qca,qca9558";
  10         model = "TP-Link TL-WDR4900 v2";
  11
  12         aliases {
  13                 led-boot = &led_system;
  14                 led-failsafe = &led_system;
  15                 led-running = &led_system;
  16                 led-upgrade = &led_system;
  17                 label-mac-device = &eth1;
  18         };
  19
  20         leds {
  21                 compatible = "gpio-leds";
  22
  23                 led_system: system {
  24                         label = "blue:system";
  25                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  26                         default-state = "on";
  27                 };
  28
  29                 usb1 {
  30                         label = "green:usb1";
  31                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  32                         trigger-sources = <&hub_port1>;
  33                         linux,default-trigger = "usbport";
  34                 };
  35
  36                 usb2 {
  37                         label = "green:usb2";
  38                         gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
  39                         trigger-sources = <&hub_port0>;
  40                         linux,default-trigger = "usbport";
  41                 };
  42
  43                 wlan2g {
  44                         label = "blue:wlan2g";
  45                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  46                         linux,default-trigger = "phy0tpt";
  47                 };
  48
  49                 qss {
  50                         label = "blue:qss";
  51                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  52                 };
  53         };
  54
  55         ath9k-leds {
  56                 compatible = "gpio-leds";
  57
  58                 wlan5g {
  59                         label = "blue:wlan5g";
  60                         gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
  61                         linux,default-trigger = "phy1tpt";
  62                 };
  63         };
  64
  65         keys {
  66                 compatible = "gpio-keys";
  67
  68                 reset {
  69                         label = "Reset button";
  70                         linux,code = <KEY_RESTART>;
  71                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  72                         debounce-interval = <60>;
  73                 };
  74         };
  75
  76         gpio-export {
  77                 compatible = "gpio-export";
  78
  79                 gpio_usb1_power {
  80                         gpio-export,name = "tp-link:power:usb1";
  81                         gpio-export,output = <1>;
  82                         gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
  83                 };
  84
  85                 gpio_usb2_power {
  86                         gpio-export,name = "tp-link:power:usb2";
  87                         gpio-export,output = <1>;
  88                         gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
  89                 };
  90         };
  91 };
  92
  93 &pcie1 {
  94         status = "okay";
  95
  96         ath9k: wifi@0,0 {
  97                 compatible = "pci168c,0033";
  98                 reg = <0x0000 0 0 0 0>;
  99                 mtd-mac-address = <&uboot 0x1fc00>;
 100                 mac-address-increment = <(-2)>;
 101                 qca,no-eeprom;
 102                 #gpio-cells = <2>;
 103                 gpio-controller;
 104         };
 105 };
 106
 107 &usb_phy0 {
 108         status = "okay";
 109 };
 110
 111 &usb0 {
 112         #address-cells = <1>;
 113         #size-cells = <0>;
 114         status = "okay";
 115
 116         hub_port0: port@1 {
 117                 reg = <1>;
 118                 #trigger-source-cells = <0>;
 119         };
 120 };
 121
 122 &usb_phy1 {
 123         status = "okay";
 124 };
 125
 126 &usb1 {
 127         #address-cells = <1>;
 128         #size-cells = <0>;
 129         status = "okay";
 130
 131         hub_port1: port@1 {
 132                 reg = <1>;
 133                 #trigger-source-cells = <0>;
 134         };
 135 };
 136
 137 &spi {
 138         status = "okay";
 139
 140         flash@0 {
 141                 compatible = "jedec,spi-nor";
 142                 reg = <0>;
 143                 spi-max-frequency = <25000000>;
 144
 145                 partitions {
 146                         compatible = "fixed-partitions";
 147                         #address-cells = <1>;
 148                         #size-cells = <1>;
 149
 150                         uboot: partition@0 {
 151                                 label = "u-boot";
 152                                 reg = <0x000000 0x020000>;
 153                                 read-only;
 154                         };
 155
 156                         partition@20000 {
 157                                 compatible = "tplink,firmware";
 158                                 label = "firmware";
 159                                 reg = <0x020000 0x7d0000>;
 160                         };
 161
 162                         art: partition@7f0000 {
 163                                 label = "art";
 164                                 reg = <0x7f0000 0x010000>;
 165                                 read-only;
 166                         };
 167                 };
 168         };
 169 };
 170
 171 &mdio0 {
 172         status = "okay";
 173
 174         phy0: ethernet-phy@0 {
 175                 reg = <0>;
 176
 177                 qca,ar8327-initvals = <
 178                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 179                         0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
 180                         0x50 0xc737c737 /* LED_CTRL0 */
 181                         0x54 0x00000000 /* LED_CTRL1 */
 182                         0x58 0x00000000 /* LED_CTRL2 */
 183                         0x5c 0x0030c300 /* LED_CTRL3 */
 184                         0x7c 0x0000007e /* PORT0_STATUS */
 185                         0x94 0x0000007e /* PORT6 STATUS */
 186                 >;
 187         };
 188 };
 189
 190 &eth0 {
 191         status = "okay";
 192
 193         mtd-mac-address = <&uboot 0x1fc00>;
 194         mac-address-increment = <1>;
 195         phy-handle = <&phy0>;
 196         pll-data = <0x56000000 0x00000101 0x00001616>;
 197
 198         gmac-config {
 199                 device = <&gmac>;
 200                 rgmii-enabled = <1>;
 201         };
 202 };
 203
 204 &eth1 {
 205         status = "okay";
 206
 207         mtd-mac-address = <&uboot 0x1fc00>;
 208         pll-data = <0x03000101 0x00000101 0x00001616>;
 209
 210         fixed-link {
 211                 speed = <1000>;
 212                 full-duplex;
 213         };
 214 };
 215
 216 &wmac {
 217         status = "okay";
 218
 219         mtd-cal-data = <&art 0x1000>;
 220         mtd-mac-address = <&uboot 0x1fc00>;
 221         mac-address-increment = <(-1)>;
 222 };