target/linux/ath79/dts/qca9558_tplink_tl-wr1043nd.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca9557.dtsi"
   8
   9 / {
  10         chosen {
  11                 bootargs = "console=ttyS0,115200n8";
  12         };
  13
  14         aliases {
  15                 led-boot = &system;
  16                 led-failsafe = &system;
  17                 led-running = &system;
  18                 led-upgrade = &system;
  19         };
  20
  21         leds {
  22                 compatible = "gpio-leds";
  23
  24                 system: system {
  25                         label = "tp-link:green:system";
  26                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  27                         linux,default-trigger = "heartbeat";
  28                 };
  29
  30                 usb {
  31                         label = "tp-link:green:usb";
  32                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  33                         default-state = "off";
  34                         trigger-sources = <&hub_port0>;
  35                         linux,default-trigger = "usbport";
  36                 };
  37
  38                 wifi_green {
  39                         label = "tp-link:green:wlan";
  40                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  41                         default-state = "off";
  42                         linux,default-trigger = "phy0tpt";
  43                 };
  44
  45                 wifi_wps {
  46                         label = "tp-link:green:wps";
  47                         gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
  48                         default-state = "off";
  49                 };
  50         };
  51
  52         keys {
  53                 compatible = "gpio-keys";
  54
  55                 reset {
  56                         label = "Reset button";
  57                         linux,code = <KEY_RESTART>;
  58                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  59                         debounce-interval = <60>;
  60                 };
  61
  62                 wifi {
  63                         label = "RFKILL button";
  64                         linux,code = <KEY_RFKILL>;
  65                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  66                         debounce-interval = <60>;
  67                 };
  68         };
  69
  70         gpio-export {
  71                 compatible = "gpio-export";
  72                 #size-cells = <0>;
  73
  74                 gpio_usb_power {
  75                         gpio-export,name = "tp-link:power:usb";
  76                         gpio-export,output = <1>;
  77                         gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
  78                 };
  79         };
  80 };
  81
  82 &uart {
  83         status = "okay";
  84 };
  85
  86 &gpio {
  87         status = "okay";
  88 };
  89
  90 &usb_phy0 {
  91         status = "okay";
  92 };
  93
  94 &usb0 {
  95         #address-cells = <1>;
  96         #size-cells = <0>;
  97         status = "okay";
  98
  99         hub_port0: port@1 {
 100                 reg = <1>;
 101                 #trigger-source-cells = <0>;
 102         };
 103 };
 104
 105 &spi {
 106         status = "okay";
 107         num-cs = <1>;
 108
 109         flash@0 {
 110                 compatible = "jedec,spi-nor";
 111                 reg = <0>;
 112                 spi-max-frequency = <25000000>;
 113
 114                 partitions {
 115                         compatible = "fixed-partitions";
 116                         #address-cells = <1>;
 117                         #size-cells = <1>;
 118
 119                         uboot:  partition@0 {
 120                                 label = "u-boot";
 121                                 reg = <0x000000 0x020000>;
 122                                 read-only;
 123                         };
 124
 125                         partition@20000 {
 126                                 label = "firmware";
 127                                 reg = <0x020000 0x7d0000>;
 128                         };
 129
 130                         art: partition@7f0000 {
 131                                 label = "art";
 132                                 reg = <0x7f0000 0x010000>;
 133                                 read-only;
 134                         };
 135                 };
 136         };
 137 };
 138
 139 &mdio0 {
 140         status = "okay";
 141
 142         phy0: ethernet-phy@0 {
 143                 reg = <0>;
 144                 qca,ar8327-initvals = <
 145                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 146                         0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
 147                         0x10 0x81000080 /* POWER_ON_STRIP */
 148                         0x50 0xcc35cc35 /* LED_CTRL0 */
 149                         0x54 0xca35ca35 /* LED_CTRL1 */
 150                         0x58 0xc935c935 /* LED_CTRL2 */
 151                         0x5c 0x03ffff00 /* LED_CTRL3 */
 152                         0x7c 0x0000007e /* PORT0_STATUS */
 153                         0x94 0x0000007e /* PORT6 STATUS */
 154                 >;
 155         };
 156 };
 157
 158 &eth0 {
 159         status = "okay";
 160
 161         pll-data = <0x56000000 0x00000101 0x00001616>;
 162
 163         mtd-mac-address = <&uboot 0x1fc00>;
 164         mtd-mac-address-increment = <1>;
 165         phy-handle = <&phy0>;
 166 };
 167
 168 &eth1 {
 169         status = "okay";
 170
 171         pll-data = <0x03000101 0x00000101 0x00001616>;
 172
 173         mtd-mac-address = <&uboot 0x1fc00>;
 174
 175         fixed-link {
 176                 speed = <1000>;
 177                 full-duplex;
 178         };
 179 };
 180
 181 &wmac {
 182         status = "okay";
 183         mtd-cal-data = <&art 0x1000>;
 184         mtd-mac-address = <&uboot 0x1fc00>;
 185 };