target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca956x.dtsi"
   7
   8 / {
   9         chosen {
  10                 bootargs = "console=ttyS0,115200n8";
  11         };
  12
  13         aliases {
  14                 led-boot = &led_power;
  15                 led-failsafe = &led_power;
  16                 led-running = &led_power;
  17                 led-upgrade = &led_power;
  18         };
  19
  20         leds: leds {
  21                 compatible = "gpio-leds";
  22
  23                 wps {
  24                         label = "elecom:red:wps";
  25                         gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
  26                 };
  27         };
  28
  29         keys {
  30                 compatible = "gpio-keys";
  31
  32                 reset {
  33                         label = "reset";
  34                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  35                         linux,code = <KEY_RESTART>;
  36                         debounce-interval = <60>;
  37                 };
  38
  39                 wps {
  40                         label = "wps";
  41                         gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
  42                         linux,code = <KEY_WPS_BUTTON>;
  43                         debounce-interval = <60>;
  44                 };
  45
  46                 ap {
  47                         label = "ap";
  48                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  49                         linux,code = <BTN_0>;
  50                         linux,input-type = <EV_SW>;
  51                         debounce-interval = <60>;
  52                 };
  53         };
  54 };
  55
  56 &spi {
  57         status = "okay";
  58         num-cs = <1>;
  59
  60         flash@0 {
  61                 compatible = "jedec,spi-nor";
  62                 reg = <0>;
  63                 spi-max-frequency = <25000000>;
  64
  65                 partitions: partitions {
  66                         compatible = "fixed-partitions";
  67                         #address-cells = <1>;
  68                         #size-cells = <1>;
  69
  70                         partition@0 {
  71                                 label = "u-boot";
  72                                 reg = <0x000000 0x040000>;
  73                                 read-only;
  74                         };
  75
  76                         partition@40000 {
  77                                 label = "u-boot-env";
  78                                 reg = <0x040000 0x010000>;
  79                                 read-only;
  80                         };
  81
  82                         partition@50000 {
  83                                 label = "nvram";
  84                                 reg = <0x050000 0x020000>;
  85                                 read-only;
  86                         };
  87                 };
  88         };
  89 };
  90
  91 &mdio0 {
  92         status = "okay";
  93
  94         phy0: ethernet-phy@0 {
  95                 reg = <0>;
  96
  97                 qca,ar8327-initvals = <
  98                         0x04 0x00000080 /* PORT0 PAD MODE CTRL */
  99                         0x50 0xcf37cf37 /* LED_CTRL0 */
 100                         0x54 0x00000000 /* LED_CTRL1 */
 101                         0x58 0x00000000 /* LED_CTRL2 */
 102                         0x5c 0x03ffff00 /* LED_CTRL3 */
 103                         0x7c 0x0000007e /* PORT0_STATUS */
 104                 >;
 105         };
 106 };
 107
 108 &eth0 {
 109         status = "okay";
 110
 111         pll-data = <0x03000101 0x00000101 0x00001919>;
 112
 113         mtd-mac-address = <&art 0x1002>;
 114         mtd-mac-address-increment = <(-1)>;
 115         phy-mode = "sgmii";
 116         phy-handle = <&phy0>;
 117 };
 118
 119 &uart {
 120         status = "okay";
 121 };
 122
 123 &wmac {
 124         status = "okay";
 125         mtd-cal-data = <&art 0x1000>;
 126 };