target/linux/bmips/dts/bcm6328-innacomm-w3400v6.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2
   3 #include "bcm6328.dtsi"
   4
   5 / {
   6         model = "Innacomm W3400V6";
   7         compatible = "innacomm,w3400v6", "brcm,bcm6328";
   8
   9         aliases {
  10                 led-boot = &led_power_green;
  11                 led-failsafe = &led_power_red;
  12                 led-running = &led_power_green;
  13                 led-upgrade = &led_power_green;
  14         };
  15
  16         keys {
  17                 compatible = "gpio-keys-polled";
  18                 poll-interval = <100>;
  19
  20                 reset {
  21                         label = "reset";
  22                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  23                         linux,code = <KEY_RESTART>;
  24                         debounce-interval = <60>;
  25                 };
  26
  27                 wps {
  28                         label = "wps";
  29                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  30                         linux,code = <KEY_WPS_BUTTON>;
  31                         debounce-interval = <60>;
  32                 };
  33         };
  34
  35         bcm4318-sprom {
  36                 compatible = "brcm,bcma-sprom";
  37
  38                 pci-bus = <1>;
  39                 pci-dev = <0>;
  40
  41                 nvmem-cells = <&macaddr_cfe_6a0 1>;
  42                 nvmem-cell-names = "mac-address";
  43
  44                 brcm,sprom = "brcm/bcm4318-sprom.bin";
  45         };
  46 };
  47
  48 &ethernet {
  49         status = "okay";
  50
  51         nvmem-cells = <&macaddr_cfe_6a0 0>;
  52         nvmem-cell-names = "mac-address";
  53 };
  54
  55 &hsspi {
  56         status = "okay";
  57
  58         flash@0 {
  59                 compatible = "jedec,spi-nor";
  60                 spi-max-frequency = <16666667>;
  61                 spi-tx-bus-width = <2>;
  62                 spi-rx-bus-width = <2>;
  63                 reg = <0>;
  64
  65                 #address-cells = <1>;
  66                 #size-cells = <1>;
  67
  68                 partitions {
  69                         compatible = "fixed-partitions";
  70                         #address-cells = <1>;
  71                         #size-cells = <1>;
  72
  73                         partition@0 {
  74                                 reg = <0x000000 0x010000>;
  75                                 label = "cfe";
  76                                 read-only;
  77
  78                                 nvmem-layout {
  79                                         compatible = "fixed-layout";
  80                                         #address-cells = <1>;
  81                                         #size-cells = <1>;
  82
  83                                         macaddr_cfe_6a0: macaddr@6a0 {
  84                                                 compatible = "mac-base";
  85                                                 reg = <0x6a0 0x6>;
  86                                                 #nvmem-cell-cells = <1>;
  87                                         };
  88                                 };
  89                         };
  90
  91                         partition@10000 {
  92                                 compatible = "brcm,bcm963xx-imagetag";
  93                                 reg = <0x010000 0x7e0000>;
  94                                 label = "firmware";
  95                         };
  96
  97                         partition@7f0000 {
  98                                 reg = <0x7f0000 0x010000>;
  99                                 label = "nvram";
 100                         };
 101                 };
 102         };
 103 };
 104
 105 &leds {
 106         status = "okay";
 107
 108         pinctrl-names = "default";
 109         pinctrl-0 = <&pinctrl_leds>;
 110
 111         led@1 {
 112                 reg = <1>;
 113                 active-low;
 114                 label = "green:internet";
 115         };
 116
 117         led@2 {
 118                 reg = <2>;
 119                 active-low;
 120                 label = "red:internet";
 121         };
 122
 123         led@3 {
 124                 reg = <3>;
 125                 active-low;
 126                 label = "green:dsl";
 127         };
 128
 129         led_power_green: led@4 {
 130                 reg = <4>;
 131                 active-low;
 132                 label = "green:power";
 133                 default-state = "on";
 134         };
 135
 136         led_power_red: led@5 {
 137                 reg = <5>;
 138                 active-low;
 139                 label = "red:power";
 140                 panic-indicator;
 141         };
 142
 143         led@11 {
 144                 reg = <11>;
 145                 active-low;
 146                 label = "green:wps";
 147         };
 148 };
 149
 150 &pcie {
 151         status = "okay";
 152 };
 153
 154 &pinctrl {
 155         pinctrl_leds: leds {
 156                 function = "led";
 157                 pins = "gpio1", "gpio2", "gpio3",
 158                        "gpio4", "gpio5", "gpio11";
 159         };
 160 };
 161
 162 &switch0 {
 163         ports {
 164                 port@0 {
 165                         reg = <0>;
 166                         label = "lan4";
 167
 168                         phy-handle = <&phy1>;
 169                         phy-mode = "mii";
 170                 };
 171
 172                 port@1 {
 173                         reg = <1>;
 174                         label = "lan3";
 175
 176                         phy-handle = <&phy2>;
 177                         phy-mode = "mii";
 178                 };
 179
 180                 port@2 {
 181                         reg = <2>;
 182                         label = "lan2";
 183
 184                         phy-handle = <&phy3>;
 185                         phy-mode = "mii";
 186                 };
 187
 188                 port@3 {
 189                         reg = <3>;
 190                         label = "lan1";
 191
 192                         phy-handle = <&phy4>;
 193                         phy-mode = "mii";
 194                 };
 195         };
 196 };
 197
 198 &uart0 {
 199         status = "okay";
 200 };