2 * Copyright 2013 Gateworks Corporation
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
13 /* these are used by bootloader for disabling nodes */
33 bootargs = "console=ttymxc1,115200";
37 compatible = "gpio-leds";
41 gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
43 linux,default-trigger = "heartbeat";
48 gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */
49 default-state = "off";
54 gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */
55 default-state = "off";
60 reg = <0x10000000 0x40000000>;
64 compatible = "simple-bus";
67 compatible = "regulator-fixed";
68 regulator-name = "1P0V";
69 regulator-min-microvolt = <1000000>;
70 regulator-max-microvolt = <1000000>;
74 /* remove this fixed regulator once ltc3676__sw2 driver available */
76 compatible = "regulator-fixed";
77 regulator-name = "1P8V";
78 regulator-min-microvolt = <1800000>;
79 regulator-max-microvolt = <1800000>;
84 compatible = "regulator-fixed";
85 regulator-name = "3P3V";
86 regulator-min-microvolt = <3300000>;
87 regulator-max-microvolt = <3300000>;
91 reg_usb_h1_vbus: usb_h1_vbus {
92 compatible = "regulator-fixed";
93 regulator-name = "usb_h1_vbus";
94 regulator-min-microvolt = <5000000>;
95 regulator-max-microvolt = <5000000>;
99 reg_usb_otg_vbus: usb_otg_vbus {
100 compatible = "regulator-fixed";
101 regulator-name = "usb_otg_vbus";
102 regulator-min-microvolt = <5000000>;
103 regulator-max-microvolt = <5000000>;
104 gpio = <&gpio3 22 0>;
110 compatible = "fsl,imx6q-sabrelite-sgtl5000",
111 "fsl,imx-audio-sgtl5000";
112 model = "imx6q-sabrelite-sgtl5000";
113 ssi-controller = <&ssi1>;
114 audio-codec = <&codec>;
116 "MIC_IN", "Mic Jack",
117 "Mic Jack", "Mic Bias",
118 "Headphone Jack", "HP_OUT";
125 pinctrl-names = "default";
126 pinctrl-0 = <&pinctrl_audmux_1>;
131 pinctrl-names = "default";
132 pinctrl-0 = <&pinctrl_flexcan1_1>;
137 pinctrl-names = "default";
138 pinctrl-0 = <&pinctrl_enet_1>;
140 phy-reset-gpios = <&gpio1 30 0>;
145 pinctrl-names = "default";
146 pinctrl-0 = <&pinctrl_gpmi_nand_2>;
151 clock-frequency = <100000>;
152 pinctrl-names = "default";
153 pinctrl-0 = <&pinctrl_i2c1_1>;
157 compatible = "atmel,24c02";
163 compatible = "atmel,24c02";
169 compatible = "atmel,24c02";
175 compatible = "atmel,24c02";
181 compatible = "nxp,pca9555";
188 compatible = "gw,gsp";
193 compatible = "dallas,ds1672";
199 clock-frequency = <100000>;
200 pinctrl-names = "default";
201 pinctrl-0 = <&pinctrl_i2c2_2>;
204 pciswitch: pex8609@3f {
205 compatible = "plx,pex8609";
210 compatible = "ltc,ltc3676";
214 sw1_reg: ltc3676__sw1 {
215 regulator-min-microvolt = <1175000>;
216 regulator-max-microvolt = <1175000>;
221 sw2_reg: ltc3676__sw2 {
222 regulator-min-microvolt = <1800000>;
223 regulator-max-microvolt = <1800000>;
228 sw3_reg: ltc3676__sw3 {
229 regulator-min-microvolt = <1175000>;
230 regulator-max-microvolt = <1175000>;
235 sw4_reg: ltc3676__sw4 {
236 regulator-min-microvolt = <1500000>;
237 regulator-max-microvolt = <1500000>;
242 ldo2_reg: ltc3676__ldo2 {
243 regulator-min-microvolt = <2500000>;
244 regulator-max-microvolt = <2500000>;
249 ldo3_reg: ltc3676__ldo3 {
250 regulator-min-microvolt = <1800000>;
251 regulator-max-microvolt = <1800000>;
256 ldo4_reg: ltc3676__ldo4 {
257 regulator-min-microvolt = <3000000>;
258 regulator-max-microvolt = <3000000>;
265 clock-frequency = <100000>;
266 pinctrl-names = "default";
267 pinctrl-0 = <&pinctrl_i2c3_2>;
270 accelerometer: fxos8700@1e {
271 compatible = "fsl,fxos8700";
276 compatible = "fsl,sgtl5000";
278 clocks = <&clks 169>;
279 VDDA-supply = <®_1p8v>;
280 VDDIO-supply = <®_3p3v>;
284 compatible = "adi,adv7611";
288 touchscreen: egalax_ts@04 {
289 compatible = "eeti,egalax_ts";
291 interrupt-parent = <&gpio7>;
292 interrupts = <12 2>; /* gpio7_12 active low */
293 wakeup-gpios = <&gpio7 12 0>;
296 videoout: adv7393@2a {
297 compatible = "adi,adv7393";
301 videoin: adv7180@20 {
302 compatible = "adi,adv7180";
310 crtcs = <&ipu1 0>, <&ipu1 1>;
315 reset-gpio = <&gpio1 29 0>;
318 eth1: sky2@8 { /* MAC/PHY on bus 8 */
319 compatible = "marvell,sky2";
320 /* Filled in by U-Boot */
321 mac-address = [ 00 00 00 00 00 00 ];
326 fsl,mode = "i2s-slave";
331 pinctrl-names = "default";
332 pinctrl-0 = <&pinctrl_uart1_2>;
337 pinctrl-names = "default";
338 pinctrl-0 = <&pinctrl_uart2_3>;
343 pinctrl-names = "default";
344 pinctrl-0 = <&pinctrl_uart5_1>;
349 vbus-supply = <®_usb_otg_vbus>;
350 pinctrl-names = "default";
351 pinctrl-0 = <&pinctrl_usbotg_1>;
352 disable-over-current;
357 vbus-supply = <®_usb_h1_vbus>;
362 pinctrl-names = "default";
363 pinctrl-0 = <&pinctrl_usdhc3_2>;
364 cd-gpios = <&gpio7 0 0>;
365 vmmc-supply = <®_3p3v>;