1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
3 #include "qcom-ipq4019.dtsi"
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/soc/qcom,tcsr.h>
9 model = "AVM FRITZ!Box 4040";
10 compatible = "avm,fritzbox-4040";
14 led-failsafe = &flash;
17 label-mac-device = &gmac0;
34 compatible = "qcom,tcsr";
35 reg = <0x1949000 0x100>;
36 qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
40 compatible = "qcom,tcsr";
41 reg = <0x194b000 0x100>;
42 qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
46 compatible = "qcom,tcsr";
47 reg = <0x1953000 0x1000>;
48 qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
52 compatible = "qcom,tcsr";
53 reg = <0x1957000 0x100>;
54 qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
83 compatible = "gpio-keys";
87 gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
88 linux,code = <KEY_RFKILL>;
93 gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
94 linux,code = <KEY_WPS_BUTTON>;
99 compatible = "gpio-leds";
102 label = "green:wlan";
103 gpios = <ðphy0 0 GPIO_ACTIVE_HIGH>;
108 gpios = <ðphy0 1 GPIO_ACTIVE_HIGH>;
114 gpios = <ðphy1 0 GPIO_ACTIVE_HIGH>;
118 label = "green:power";
119 gpios = <ðphy2 1 GPIO_ACTIVE_HIGH>;
124 gpios = <ðphy3 0 GPIO_ACTIVE_HIGH>;
128 label = "amber:info";
129 gpios = <ðphy3 1 GPIO_ACTIVE_HIGH>;
135 serial_pins: serial_pinmux {
137 pins = "gpio60", "gpio61";
138 function = "blsp_uart0";
143 spi_0_pins: spi_0_pinmux {
145 function = "blsp_spi0";
146 pins = "gpio55", "gpio56", "gpio57";
147 drive-strength = <12>;
154 drive-strength = <2>;
169 &blsp1_spi1 { /* BLSP1 QUP1 */
170 pinctrl-0 = <&spi_0_pins>;
171 pinctrl-names = "default";
173 cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
176 compatible = "jedec,spi-nor";
178 spi-max-frequency = <24000000>;
183 compatible = "fixed-partitions";
184 #address-cells = <1>;
189 reg = <0x00000000 0x00040000>;
194 reg = <0x00040000 0x00020000>;
199 reg = <0x00060000 0x00060000>;
204 reg = <0x000c0000 0x00010000>;
209 reg = <0x000d0000 0x00010000>;
213 label = "APPSBLENV"; /* uboot env - empty */
214 reg = <0x000e0000 0x00010000>;
218 label = "urlader"; /* APPSBL */
219 reg = <0x000f0000 0x0002dc000>;
223 /* make a backup of this partition! */
224 label = "urlader_config";
225 reg = <0x0011dc00 0x00002400>;
230 reg = <0x00120000 0x00080000>;
235 reg = <0x001a0000 0x00080000>;
240 reg = <0x00220000 0x00080000>;
244 compatible = "denx,fit";
246 reg = <0x002a0000 0x01c60000>;
248 partition12@1f00000 {
250 reg = <0x01f00000 0x00100000>;
257 pinctrl-0 = <&serial_pins>;
258 pinctrl-names = "default";
273 line-name = "enable USB3 power";
274 gpios = <1 GPIO_ACTIVE_HIGH>;
303 qcom,ath10k-calibration-variant = "AVM-FRITZBox-4040";
308 qcom,ath10k-calibration-variant = "AVM-FRITZBox-4040";