1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-ipq8064-v2.0.dtsi"
4 #include <dt-bindings/input/input.h>
5 #include <dt-bindings/soc/qcom,tcsr.h>
8 compatible = "asrock,g10", "qcom,ipq8064";
15 led-boot = &led_status_blue;
16 led-failsafe = &led_status_amber;
17 led-running = &led_status_blue;
18 led-upgrade = &led_status_amber;
22 bootargs-override = "console=ttyMSM0,115200n8";
26 compatible = "gpio-leds";
28 pinctrl-0 = <&led_pins>;
29 pinctrl-names = "default";
32 * this is a bit misleading. Because there are about seven
33 * multicolor LEDs connected all wired together in parallel.
37 label = "yellow:status";
38 gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
41 led_status_amber: status_amber {
42 label = "amber:status";
43 gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
46 led_status_blue: status_blue {
47 label = "blue:status";
48 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
52 * LED is declared in vendors boardfile but it's not
53 * working and the manual doesn't mention anything
54 * about the LED being white.
57 label = "white:status";
58 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
67 compatible = "i2c-gpio";
68 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>, /* sda */
69 <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; /* scl */
70 i2c-gpio,delay-us = <5>;
71 i2c-gpio,scl-output-only;
75 compatible = "sonix,sn8f25e21";
80 compatible = "gpio-keys";
82 pinctrl-0 = <&button_pins>;
83 pinctrl-names = "default";
87 gpios = <&qcom_pinmux 15 GPIO_ACTIVE_LOW>;
93 gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
94 linux,code = <KEY_RESTART>;
99 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
100 linux,code = <KEY_WPS_BUTTON>;
105 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
106 linux,code = <KEY_WPS_BUTTON>;
118 pinctrl-0 = <&rgmii2_pins>;
119 pinctrl-names = "default";
143 pinctrl-0 = <&uart0_pins>;
144 pinctrl-names = "default";
150 pinctrl-0 = <&mdio0_pins>;
151 pinctrl-names = "default";
155 qca,ar8327-initvals = <
156 0x00004 0x7600000 /* PAD0_MODE */
157 0x00008 0x1000000 /* PAD5_MODE */
158 0x0000c 0x80 /* PAD6_MODE */
159 0x000e4 0x6a545 /* MAC_POWER_SEL */
160 0x000e0 0xc74164de /* SGMII_CTRL */
161 0x0007c 0x4e /* PORT0_STATUS */
162 0x00094 0x4e /* PORT6_STATUS */
170 pinctrl-0 = <&nand_pins>;
171 pinctrl-names = "default";
175 compatible = "qcom,nandcs";
177 nand-ecc-strength = <4>;
178 nand-bus-width = <8>;
179 nand-ecc-step-size = <512>;
182 compatible = "qcom,smem-part";
198 pins = "gpio7", "gpio8", "gpio9", "gpio26";
200 drive-strength = <2>;
205 button_pins: button_pins {
207 pins = "gpio15", "gpio16", "gpio64", "gpio65";
209 drive-strength = <2>;
214 uart0_pins: uart0_pins {
216 pins = "gpio10", "gpio11";
218 drive-strength = <10>;
225 pinctrl-0 = <&i2c4_pins>;
226 pinctrl-names = "default";
238 qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
241 /delete-node/ &pcie2_pins;
242 /delete-node/ &pcie2;