1 #include "qcom-ipq8065-v1.0.dtsi"
3 #include <dt-bindings/input/input.h>
6 model = "Netgear Nighthawk X4S R7800";
7 compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064";
10 reg = <0x42000000 0x1e000000>;
11 device_type = "memory";
19 reg = <0x41200000 0x300000>;
24 reg = <0x5fe00000 0x200000>;
33 led-boot = &power_white;
34 led-failsafe = &power_white;
35 led-running = &power_white;
36 led-upgrade = &power_amber;
40 linux,stdout-path = "serial0:115200n8";
45 button_pins: button_pins {
47 pins = "gpio6", "gpio54", "gpio65";
54 i2c4_pins: i2c4_pinmux {
56 pins = "gpio12", "gpio13";
58 drive-strength = <12>;
64 pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
65 "gpio24","gpio26", "gpio53", "gpio64", "gpio67";
71 nand_pins: nand_pins {
73 pins = "gpio34", "gpio35", "gpio36",
74 "gpio37", "gpio38", "gpio39",
75 "gpio40", "gpio41", "gpio42",
76 "gpio43", "gpio44", "gpio45",
79 drive-strength = <10>;
87 pins = "gpio40", "gpio41", "gpio42",
88 "gpio43", "gpio44", "gpio45",
94 mdio0_pins: mdio0_pins {
96 pins = "gpio0", "gpio1";
108 rgmii2_pins: rgmii2_pins {
110 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
111 "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
113 drive-strength = <8>;
118 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
125 pins = "gpio18", "gpio19", "gpio21";
131 pins = "gpio18", "gpio19";
132 drive-strength = <10>;
137 drive-strength = <10>;
143 drive-strength = <12>;
147 spi6_pins: spi6_pins {
149 pins = "gpio55", "gpio56", "gpio58";
156 drive-strength = <12>;
161 drive-strength = <14>;
166 drive-strength = <12>;
172 drive-strength = <12>;
177 drive-strength = <10>;
183 usb0_pwr_en_pins: usb0_pwr_en_pins {
187 drive-strength = <12>;
193 usb1_pwr_en_pins: usb1_pwr_en_pins {
195 pins = "gpio16", "gpio68";
197 drive-strength = <12>;
205 qcom,mode = <GSBI_PROT_I2C_UART>;
211 * The i2c device on gsbi4 should not be enabled.
212 * On ipq806x designs gsbi4 i2c is meant for exclusive
213 * RPM usage. Turning this on in kernel manifests as
214 * i2c failure for the RPM.
218 gsbi5: gsbi@1a200000 {
219 qcom,mode = <GSBI_PROT_SPI>;
224 spi-max-frequency = <50000000>;
225 pinctrl-0 = <&spi_pins>;
226 pinctrl-names = "default";
228 cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
231 compatible = "jedec,spi-nor";
232 #address-cells = <1>;
234 spi-max-frequency = <50000000>;
237 linux,part-probe = "qcom-smem";
242 gsbi6: gsbi@16500000 {
243 qcom,mode = <GSBI_PROT_SPI>;
247 spi-max-frequency = <6000000>;
248 pinctrl-0 = <&spi6_pins>;
249 pinctrl-names = "default";
251 cs-gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
254 compatible = "spi-nor";
256 spi-max-frequency = <6000000>;
266 ports-implemented = <0x1>;
270 phy@100f8800 { /* USB3 port 1 HS phy */
274 phy@100f8830 { /* USB3 port 1 SS phy */
278 phy@110f8800 { /* USB3 port 0 HS phy */
282 phy@110f8830 { /* USB3 port 0 SS phy */
289 pinctrl-0 = <&usb0_pwr_en_pins>;
290 pinctrl-names = "default";
296 pinctrl-0 = <&usb1_pwr_en_pins>;
297 pinctrl-names = "default";
300 pcie0: pci@1b500000 {
302 phy-tx0-term-offset = <7>;
305 pcie1: pci@1b700000 {
307 phy-tx0-term-offset = <7>;
313 pinctrl-0 = <&nand_pins>;
314 pinctrl-names = "default";
316 nand-ecc-strength = <4>;
317 nand-ecc-step-size = <512>;
318 nand-bus-width = <8>;
320 #address-cells = <1>;
325 reg = <0x0000000 0x0c80000>;
331 reg = <0x0c80000 0x0500000>;
337 reg = <0x1180000 0x0080000>;
343 reg = <0x1200000 0x0140000>;
347 artbak: art@1340000 {
349 reg = <0x1340000 0x0140000>;
355 reg = <0x1480000 0x0200000>;
360 reg = <0x1680000 0x1E00000>;
365 reg = <0x3480000 0x4480000>;
371 reg = <0x7900000 0x0700000>;
377 reg = <0x1480000 0x2000000>;
382 compatible = "virtual,mdio-gpio";
383 #address-cells = <1>;
385 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
386 pinctrl-0 = <&mdio0_pins>;
387 pinctrl-names = "default";
390 phy0: ethernet-phy@0 {
391 device_type = "ethernet-phy";
393 qca,ar8327-initvals = <
394 0x00004 0x7600000 /* PAD0_MODE */
395 0x00008 0x1000000 /* PAD5_MODE */
396 0x0000c 0x80 /* PAD6_MODE */
397 0x000e4 0xaa545 /* MAC_POWER_SEL */
398 0x000e0 0xc74164de /* SGMII_CTRL */
399 0x0007c 0x4e /* PORT0_STATUS */
400 0x00094 0x4e /* PORT6_STATUS */
401 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
402 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
403 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
404 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
405 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
406 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
407 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
408 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
409 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
410 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
411 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
412 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
413 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
414 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
417 0x1 0x5e /* VLAN1 Ports 1/2/3/4/6 */
418 0x2 0x21 /* VLAN2 Ports 0/5 */
422 phy4: ethernet-phy@4 {
423 device_type = "ethernet-phy";
425 qca,ar8327-initvals = <
426 0x000e4 0x6a545 /* MAC_POWER_SEL */
427 0x0000c 0x80 /* PAD6_MODE */
432 gmac1: ethernet@37200000 {
436 qcom,phy_mdio_addr = <4>;
437 qcom,poll_required = <0>;
438 qcom,rgmii_delay = <1>;
439 qcom,phy_mii_type = <0>;
440 qcom,emulation = <0>;
444 pinctrl-0 = <&rgmii2_pins>;
445 pinctrl-names = "default";
447 mtd-mac-address = <&art 6>;
455 gmac2: ethernet@37400000 {
459 qcom,phy_mdio_addr = <0>; /* none */
460 qcom,poll_required = <0>; /* no polling */
461 qcom,rgmii_delay = <0>;
462 qcom,phy_mii_type = <1>;
463 qcom,emulation = <0>;
467 mtd-mac-address = <&art 0>;
476 pinctrl-0 = <&i2c4_pins>;
477 pinctrl-names = "default";
482 compatible = "gpio-keys";
483 pinctrl-0 = <&button_pins>;
484 pinctrl-names = "default";
488 gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
489 linux,code = <KEY_RFKILL>;
490 debounce-interval = <60>;
496 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
497 linux,code = <KEY_RESTART>;
498 debounce-interval = <60>;
504 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
505 linux,code = <KEY_WPS_BUTTON>;
506 debounce-interval = <60>;
512 compatible = "gpio-leds";
513 pinctrl-0 = <&led_pins>;
514 pinctrl-names = "default";
516 power_white: power_white {
517 label = "r7800:white:power";
518 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
519 default-state = "on";
522 power_amber: power_amber {
523 label = "r7800:amber:power";
524 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
528 label = "r7800:white:wan";
529 gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
533 label = "r7800:amber:wan";
534 gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
538 label = "r7800:white:usb1";
539 gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
543 label = "r7800:white:usb2";
544 gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
548 label = "r7800:white:esata";
549 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
553 label = "r7800:white:rfkill";
554 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
558 label = "r7800:white:wps";
559 gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
563 label = "r7800:white:wifi";
564 gpios = <&qcom_pinmux 67 GPIO_ACTIVE_HIGH>;