1 #include "qcom-ipq8064-v1.0.dtsi"
3 #include <dt-bindings/input/input.h>
4 #include <dt-bindings/soc/qcom,tcsr.h>
7 model = "Netgear Nighthawk X4 R7500";
8 compatible = "netgear,r7500", "qcom,ipq8064";
11 reg = <0x42000000 0xe000000>;
12 device_type = "memory";
20 reg = <0x41200000 0x300000>;
26 serial0 = &gsbi4_serial;
29 led-boot = &power_white;
30 led-failsafe = &power_amber;
31 led-running = &power_white;
32 led-upgrade = &power_amber;
36 bootargs = "rootfstype=squashfs noinitrd";
37 linux,stdout-path = "serial0:115200n8";
42 button_pins: button_pins {
44 pins = "gpio6", "gpio54", "gpio65";
51 i2c4_pins: i2c4_pinmux {
53 pins = "gpio12", "gpio13";
55 drive-strength = <12>;
62 pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
63 "gpio24","gpio26", "gpio53", "gpio64";
70 mdio0_pins: mdio0_pins {
72 pins = "gpio0", "gpio1";
79 nand_pins: nand_pins {
81 pins = "gpio34", "gpio35", "gpio36",
82 "gpio37", "gpio38", "gpio39",
83 "gpio40", "gpio41", "gpio42",
84 "gpio43", "gpio44", "gpio45",
87 drive-strength = <10>;
95 pins = "gpio40", "gpio41", "gpio42",
96 "gpio43", "gpio44", "gpio45",
102 rgmii2_pins: rgmii2_pins {
104 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
105 "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
107 drive-strength = <8>;
114 qcom,mode = <GSBI_PROT_I2C_UART>;
120 * The i2c device on gsbi4 should not be enabled.
121 * On ipq806x designs gsbi4 i2c is meant for exclusive
122 * RPM usage. Turning this on in kernel manifests as
123 * i2c failure for the RPM.
135 phy@100f8800 { /* USB3 port 1 HS phy */
136 clocks = <&gcc USB30_0_UTMI_CLK>;
140 phy@100f8830 { /* USB3 port 1 SS phy */
141 clocks = <&gcc USB30_0_MASTER_CLK>;
145 phy@110f8800 { /* USB3 port 0 HS phy */
146 clocks = <&gcc USB30_1_UTMI_CLK>;
150 phy@110f8830 { /* USB3 port 0 SS phy */
151 clocks = <&gcc USB30_1_MASTER_CLK>;
156 clocks = <&gcc USB30_1_MASTER_CLK>;
161 clocks = <&gcc USB30_0_MASTER_CLK>;
165 pcie0: pci@1b500000 {
169 pcie1: pci@1b700000 {
177 pinctrl-0 = <&nand_pins>;
178 pinctrl-names = "default";
182 compatible = "qcom,nandcs";
184 nand-ecc-strength = <4>;
185 nand-bus-width = <8>;
186 nand-ecc-step-size = <512>;
189 compatible = "fixed-partitions";
190 #address-cells = <1>;
195 reg = <0x0000000 0x0c80000>;
201 reg = <0x0c80000 0x0500000>;
207 reg = <0x1180000 0x0080000>;
213 reg = <0x1200000 0x0140000>;
219 reg = <0x1340000 0x0400000>;
224 reg = <0x1740000 0x1600000>;
229 reg = <0x2d40000 0x0c00000>;
235 reg = <0x3940000 0x46c0000>;
241 reg = <0x1340000 0x1a00000>;
248 compatible = "virtual,mdio-gpio";
249 #address-cells = <1>;
251 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
252 pinctrl-0 = <&mdio0_pins>;
253 pinctrl-names = "default";
255 phy0: ethernet-phy@0 {
256 device_type = "ethernet-phy";
258 qca,ar8327-initvals = <
259 0x00004 0x7600000 /* PAD0_MODE */
260 0x00008 0x1000000 /* PAD5_MODE */
261 0x0000c 0x80 /* PAD6_MODE */
262 0x000e4 0x6a545 /* MAC_POWER_SEL */
263 0x000e0 0xc74164de /* SGMII_CTRL */
264 0x0007c 0x4e /* PORT0_STATUS */
265 0x00094 0x4e /* PORT6_STATUS */
269 phy4: ethernet-phy@4 {
270 device_type = "ethernet-phy";
275 gmac1: ethernet@37200000 {
280 pinctrl-0 = <&rgmii2_pins>;
281 pinctrl-names = "default";
283 mtd-mac-address = <&art 6>;
291 gmac2: ethernet@37400000 {
296 mtd-mac-address = <&art 0>;
306 compatible = "gpio-keys";
307 pinctrl-0 = <&button_pins>;
308 pinctrl-names = "default";
312 gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
313 linux,code = <KEY_RFKILL>;
318 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
319 linux,code = <KEY_RESTART>;
324 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
325 linux,code = <KEY_WPS_BUTTON>;
330 compatible = "gpio-leds";
331 pinctrl-0 = <&led_pins>;
332 pinctrl-names = "default";
335 label = "r7500:white:usb1";
336 gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
340 label = "r7500:white:usb2";
341 gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
344 power_amber: power_amber {
345 label = "r7500:amber:power";
346 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
350 label = "r7500:white:wan";
351 gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
355 label = "r7500:amber:wan";
356 gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
360 label = "r7500:white:wps";
361 gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
365 label = "r7500:white:esata";
366 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
369 power_white: power_white {
370 label = "r7500:white:power";
371 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
372 default-state = "keep";
376 label = "r7500:white:wifi";
377 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
383 qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
384 compatible = "qcom,tcsr";