5 #include <dt-bindings/input/input.h>
8 model = "BTHOMEHUBV5A - BT Home Hub 5A";
11 led-boot = &power_green;
12 led-failsafe = &power_red;
13 led-running = &power_blue;
15 led-internet = &broadband_blue;
16 led-wifi = &wireless_blue;
20 reg = <0x0 0x8000000>;
26 compatible = "gen_nand", "lantiq,nand-xway";
29 reg = <0x1 0x0 0x2000000>;
33 nand-ecc-strength = <3>;
34 nand-ecc-step-size = <256>;
37 compatible = "fixed-partitions";
48 reg = <0xa0000 0x20000>;
53 reg = <0xc0000 0x40000>;
57 reg = <0x100000 0x7e80000>;
60 * last 512 KiB are for the bad block table, not writable
66 gpio: pinmux@E100B10 {
67 pinctrl-names = "default";
68 pinctrl-0 = <&state_default>;
70 state_default: pinmux {
72 lantiq,groups = "mdio";
73 lantiq,function = "mdio";
89 lantiq,open-drain = <0>;
93 lantiq,groups = "nand cle", "nand ale";
94 lantiq,function = "ebu";
96 lantiq,open-drain = <0>;
100 lantiq,groups = "nand cs1";
101 lantiq,function = "ebu";
102 lantiq,open-drain = <0>;
110 gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
115 compatible = "lantiq,phy-xrx200";
116 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
117 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
122 compatible = "gpio-keys-polled";
123 #address-cells = <1>;
125 poll-interval = <100>;
129 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
130 linux,code = <KEY_RESTART>;
135 gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
136 linux,code = <KEY_WPS_BUTTON>;
141 gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
142 linux,code = <KEY_POWER>;
147 compatible = "gpio-leds";
149 /* broadband-* is a single RGB led */
151 label = "bthomehubv5a:red:broadband";
152 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
155 label = "bthomehubv5a:green:broadband";
156 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
158 broadband_blue: broadband-blue {
159 label = "bthomehubv5a:blue:broadband";
160 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
163 /* wireless-* is a single RGB led */
165 label = "bthomehubv5a:red:wireless";
166 gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
169 label = "bthomehubv5a:green:wireless";
170 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
172 wireless_blue: wireless-blue {
173 label = "bthomehubv5a:blue:wireless";
174 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
177 /* power-* is a single RGB led */
178 power_red: power-red {
179 label = "bthomehubv5a:red:power";
180 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
182 power_green: power-green {
183 label = "bthomehubv5a:green:power";
184 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
185 default-state = "keep";
187 power_blue: power-blue {
188 label = "bthomehubv5a:blue:power";
189 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
194 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
201 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
204 compatible = "pci168c,002d";
205 reg = <0x7000 0 0 0 0>;
206 qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
213 compatible = "lantiq,xrx200-pdi";
214 #address-cells = <1>;
220 compatible = "lantiq,xrx200-pdi-port";
223 phy-handle = <&phy0>;
226 compatible = "lantiq,xrx200-pdi-port";
229 phy-handle = <&phy1>;
232 compatible = "lantiq,xrx200-pdi-port";
235 phy-handle = <&phy11>;
238 compatible = "lantiq,xrx200-pdi-port";
241 phy-handle = <&phy13>;
246 compatible = "lantiq,xrx200-pdi";
247 #address-cells = <1>;
253 compatible = "lantiq,xrx200-pdi-port";
256 phy-handle = <&phy5>;
261 #address-cells = <1>;
263 compatible = "lantiq,xrx200-mdio";
265 phy0: ethernet-phy@0 {
267 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
269 phy1: ethernet-phy@1 {
271 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
273 phy5: ethernet-phy@5 {
275 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
277 phy11: ethernet-phy@11 {
279 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
281 phy13: ethernet-phy@13 {
283 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";