6 model = "BTHOMEHUBV5A - BT Home Hub 5A";
9 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
12 internet = &broadband_blue;
13 wifi = &wireless_blue;
18 reg = <0x0 0x8000000>;
24 compatible = "gen_nand", "lantiq,nand-xway";
27 reg = <0 0x0 0x2000000>;
38 reg = <0x40000 0x40000>;
40 caldata: partition@80000 {
42 reg = <0x80000 0x20000>;
47 reg = <0xa0000 0x200000>;
51 reg = <0x2a0000 0x7d60000>;
56 gpio: pinmux@E100B10 {
57 pinctrl-names = "default";
58 pinctrl-0 = <&state_default>;
60 interrupt-parent = <&icu0>;
61 interrupts = <166 135 66 40 41 42 38>;
63 state_default: pinmux {
65 lantiq,groups = "mdio";
66 lantiq,function = "mdio";
82 lantiq,open-drain = <0>;
86 lantiq,groups = "nand cle", "nand ale";
87 lantiq,function = "ebu";
89 lantiq,open-drain = <0>;
93 lantiq,groups = "nand cs1";
94 lantiq,function = "ebu";
95 lantiq,open-drain = <0>;
102 #address-cells = <1>;
104 compatible = "lantiq,xrx200-net";
105 reg = < 0xE108000 0x3000 /* switch */
106 0xE10B100 0x70 /* mdio */
107 0xE10B1D8 0x30 /* mii */
108 0xE10B308 0x30 >; /* pmac */
109 interrupt-parent = <&icu0>;
110 interrupts = <73 72>;
113 compatible = "lantiq,xrx200-pdi";
114 #address-cells = <1>;
117 mtd-mac-address = <&caldata 0x110c>;
121 compatible = "lantiq,xrx200-pdi-port";
124 phy-handle = <&phy0>;
127 compatible = "lantiq,xrx200-pdi-port";
130 phy-handle = <&phy1>;
133 compatible = "lantiq,xrx200-pdi-port";
136 phy-handle = <&phy11>;
139 compatible = "lantiq,xrx200-pdi-port";
142 phy-handle = <&phy13>;
147 compatible = "lantiq,xrx200-pdi";
148 #address-cells = <1>;
151 mtd-mac-address = <&caldata 0x110c>;
152 mtd-mac-address-increment = <4>;
156 compatible = "lantiq,xrx200-pdi-port";
159 phy-handle = <&phy5>;
164 #address-cells = <1>;
166 compatible = "lantiq,xrx200-mdio";
168 phy0: ethernet-phy@0 {
170 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
172 phy1: ethernet-phy@1 {
174 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
176 phy5: ethernet-phy@5 {
178 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
180 phy11: ethernet-phy@11 {
182 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
184 phy13: ethernet-phy@13 {
186 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
193 gpios = <&gpio 33 0>;
198 lantiq,bus-clock = <33333333>;
199 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
200 interrupt-map = <0x7000 0 0 1 &icu0 30 1>;
201 gpio-reset = <&gpio 21 0>;
206 compatible = "lantiq,phy-xrx200";
207 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
208 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
213 compatible = "ath9k,eeprom";
214 ath,eep-flash = <&caldata 0x1000>;
215 ath,mac-offset = <0x110c>;
216 ath,mac-increment = <2>;
217 ath,pci-slot = <0xe>; /* 14 */
221 compatible = "gpio-keys-polled";
222 #address-cells = <1>;
224 poll-interval = <100>;
229 linux,code = <0x198>;
234 gpios = <&gpio 25 1>;
235 linux,code = <0x211>;
240 gpios = <&gpio 39 1>;
241 linux,code = <0x198>;
246 compatible = "gpio-leds";
249 label = "soc:red:broadband";
253 label = "soc:green:broadband";
256 broadband_blue: broadband-blue {
257 label = "soc:blue:broadband";
262 label = "soc:red:wireless";
266 label = "soc:green:wireless";
267 gpios = <&gpio 10 1>;
269 wireless_blue: wireless-blue {
270 label = "soc:blue:wireless";
271 gpios = <&gpio 11 1>;
275 label = "soc:red:power";
276 gpios = <&gpio 12 1>;
279 label = "soc:green:power";
280 gpios = <&gpio 14 1>;
283 label = "soc:blue:power";
284 gpios = <&gpio 15 1>;
289 gpios = <&gpio 19 0>;