5 #include <dt-bindings/input/input.h>
8 compatible = "bt,homehub-v5a", "lantiq,xway", "lantiq,vr9";
9 model = "BT Home Hub 5A";
12 bootargs = "console=ttyLTQ0,115200";
16 led-boot = &power_green;
17 led-failsafe = &power_red;
18 led-running = &power_blue;
20 led-dsl = &broadband_blue;
21 led-wifi = &wireless_blue;
25 reg = <0x0 0x8000000>;
31 compatible = "lantiq,nand-xway";
34 reg = <0x1 0x0 0x2000000>;
38 nand-ecc-strength = <3>;
39 nand-ecc-step-size = <256>;
42 compatible = "fixed-partitions";
53 reg = <0xa0000 0x20000>;
58 reg = <0xc0000 0x40000>;
62 reg = <0x100000 0x7e80000>;
65 * last 512 KiB are for the bad block table, not writable
71 gpio: pinmux@E100B10 {
72 pinctrl-names = "default";
73 pinctrl-0 = <&state_default>;
75 state_default: pinmux {
77 lantiq,groups = "mdio";
78 lantiq,function = "mdio";
94 lantiq,open-drain = <0>;
98 lantiq,groups = "nand cle", "nand ale";
99 lantiq,function = "ebu";
101 lantiq,open-drain = <0>;
105 lantiq,groups = "nand cs1";
106 lantiq,function = "ebu";
107 lantiq,open-drain = <0>;
115 gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
120 compatible = "lantiq,phy-xrx200";
121 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
122 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
127 compatible = "gpio-keys-polled";
128 #address-cells = <1>;
130 poll-interval = <100>;
134 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
135 linux,code = <KEY_RESTART>;
140 gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
141 linux,code = <KEY_WPS_BUTTON>;
146 gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
147 linux,code = <KEY_POWER>;
152 compatible = "gpio-leds";
154 /* broadband-* is a single RGB led */
156 label = "bthomehubv5a:red:broadband";
157 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
160 label = "bthomehubv5a:green:broadband";
161 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
163 broadband_blue: broadband-blue {
164 label = "bthomehubv5a:blue:broadband";
165 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
168 /* wireless-* is a single RGB led */
170 label = "bthomehubv5a:red:wireless";
171 gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
174 label = "bthomehubv5a:green:wireless";
175 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
177 wireless_blue: wireless-blue {
178 label = "bthomehubv5a:blue:wireless";
179 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
182 /* power-* is a single RGB led */
183 power_red: power-red {
184 label = "bthomehubv5a:red:power";
185 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
187 power_green: power-green {
188 label = "bthomehubv5a:green:power";
189 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
190 default-state = "keep";
192 power_blue: power-blue {
193 label = "bthomehubv5a:blue:power";
194 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
199 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
206 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
209 compatible = "pci168c,002d";
210 reg = <0x7000 0 0 0 0>;
211 qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
218 compatible = "lantiq,xrx200-pdi";
219 #address-cells = <1>;
225 compatible = "lantiq,xrx200-pdi-port";
228 phy-handle = <&phy0>;
231 compatible = "lantiq,xrx200-pdi-port";
234 phy-handle = <&phy1>;
237 compatible = "lantiq,xrx200-pdi-port";
240 phy-handle = <&phy11>;
243 compatible = "lantiq,xrx200-pdi-port";
246 phy-handle = <&phy13>;
249 compatible = "lantiq,xrx200-pdi-port";
252 phy-handle = <&phy5>;
257 #address-cells = <1>;
259 compatible = "lantiq,xrx200-mdio";
261 phy0: ethernet-phy@0 {
263 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
265 phy1: ethernet-phy@1 {
267 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
269 phy5: ethernet-phy@5 {
271 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
273 phy11: ethernet-phy@11 {
275 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
277 phy13: ethernet-phy@13 {
279 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";