6 model = "BTHOMEHUBV5A - BT Home Hub 5A";
9 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
13 failsafe = &power_red;
14 running = &power_blue;
16 internet = &broadband_blue;
17 wifi = &wireless_blue;
22 reg = <0x0 0x8000000>;
28 compatible = "gen_nand", "lantiq,nand-xway";
31 reg = <0 0x0 0x2000000>;
42 reg = <0x40000 0x40000>;
44 caldata: partition@80000 {
46 reg = <0x80000 0x20000>;
51 reg = <0xa0000 0x200000>;
55 reg = <0x2a0000 0x7d60000>;
60 gpio: pinmux@E100B10 {
61 pinctrl-names = "default";
62 pinctrl-0 = <&state_default>;
64 interrupt-parent = <&icu0>;
65 interrupts = <166 135 66 40 41 42 38>;
67 state_default: pinmux {
69 lantiq,groups = "mdio";
70 lantiq,function = "mdio";
86 lantiq,open-drain = <0>;
90 lantiq,groups = "nand cle", "nand ale";
91 lantiq,function = "ebu";
93 lantiq,open-drain = <0>;
97 lantiq,groups = "nand cs1";
98 lantiq,function = "ebu";
99 lantiq,open-drain = <0>;
106 #address-cells = <1>;
108 compatible = "lantiq,xrx200-net";
109 reg = < 0xE108000 0x3000 /* switch */
110 0xE10B100 0x70 /* mdio */
111 0xE10B1D8 0x30 /* mii */
112 0xE10B308 0x30 >; /* pmac */
113 interrupt-parent = <&icu0>;
114 interrupts = <73 72>;
117 compatible = "lantiq,xrx200-pdi";
118 #address-cells = <1>;
121 mtd-mac-address = <&caldata 0x110c>;
125 compatible = "lantiq,xrx200-pdi-port";
128 phy-handle = <&phy0>;
131 compatible = "lantiq,xrx200-pdi-port";
134 phy-handle = <&phy1>;
137 compatible = "lantiq,xrx200-pdi-port";
140 phy-handle = <&phy11>;
143 compatible = "lantiq,xrx200-pdi-port";
146 phy-handle = <&phy13>;
151 compatible = "lantiq,xrx200-pdi";
152 #address-cells = <1>;
155 mtd-mac-address = <&caldata 0x110c>;
156 mtd-mac-address-increment = <4>;
160 compatible = "lantiq,xrx200-pdi-port";
163 phy-handle = <&phy5>;
168 #address-cells = <1>;
170 compatible = "lantiq,xrx200-mdio";
172 phy0: ethernet-phy@0 {
174 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
176 phy1: ethernet-phy@1 {
178 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
180 phy5: ethernet-phy@5 {
182 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
184 phy11: ethernet-phy@11 {
186 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
188 phy13: ethernet-phy@13 {
190 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
197 gpios = <&gpio 33 0>;
202 lantiq,bus-clock = <33333333>;
203 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
204 interrupt-map = <0x7000 0 0 1 &icu0 30 1>;
205 gpio-reset = <&gpio 21 0>;
210 compatible = "lantiq,phy-xrx200";
211 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
212 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
217 compatible = "ath9k,eeprom";
218 ath,eep-flash = <&caldata 0x1000>;
219 ath,mac-offset = <0x110c>;
220 ath,mac-increment = <2>;
221 ath,pci-slot = <0xe>; /* 14 */
225 compatible = "gpio-keys-polled";
226 #address-cells = <1>;
228 poll-interval = <100>;
233 linux,code = <0x198>;
238 gpios = <&gpio 25 1>;
239 linux,code = <0x211>;
244 gpios = <&gpio 39 1>;
245 linux,code = <0x198>;
250 compatible = "gpio-leds";
252 /* broadband-* is a single RGB led */
254 label = "soc:red:broadband";
258 label = "soc:green:broadband";
261 broadband_blue: broadband-blue {
262 label = "soc:blue:broadband";
266 /* wireless-* is a single RGB led */
268 label = "soc:red:wireless";
272 label = "soc:green:wireless";
273 gpios = <&gpio 10 1>;
275 wireless_blue: wireless-blue {
276 label = "soc:blue:wireless";
277 gpios = <&gpio 11 1>;
280 /* power-* is a single RGB led */
281 power_red: power-red {
282 label = "soc:red:power";
283 gpios = <&gpio 12 1>;
285 power_green: power-green {
286 label = "soc:green:power";
287 gpios = <&gpio 14 1>;
288 default-state = "keep";
290 power_blue: power-blue {
291 label = "soc:blue:power";
292 gpios = <&gpio 15 1>;
297 gpios = <&gpio 19 0>;