5 #include <dt-bindings/input/input.h>
8 model = "BTHOMEHUBV5A - BT Home Hub 5A";
11 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
15 led-boot = &power_green;
16 led-failsafe = &power_red;
17 led-running = &power_blue;
19 led-internet = &broadband_blue;
20 led-wifi = &wireless_blue;
24 reg = <0x0 0x8000000>;
30 compatible = "gen_nand", "lantiq,nand-xway";
33 reg = <0x1 0x0 0x2000000>;
38 compatible = "fixed-partitions";
49 reg = <0x40000 0x40000>;
51 caldata: partition@80000 {
53 reg = <0x80000 0x20000>;
58 reg = <0xa0000 0x200000>;
62 reg = <0x2a0000 0x7d60000>;
68 gpio: pinmux@E100B10 {
69 pinctrl-names = "default";
70 pinctrl-0 = <&state_default>;
72 state_default: pinmux {
74 lantiq,groups = "mdio";
75 lantiq,function = "mdio";
91 lantiq,open-drain = <0>;
95 lantiq,groups = "nand cle", "nand ale";
96 lantiq,function = "ebu";
98 lantiq,open-drain = <0>;
102 lantiq,groups = "nand cs1";
103 lantiq,function = "ebu";
104 lantiq,open-drain = <0>;
112 gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
117 compatible = "lantiq,phy-xrx200";
118 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
119 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
124 compatible = "gpio-keys-polled";
125 #address-cells = <1>;
127 poll-interval = <100>;
131 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
132 linux,code = <KEY_RESTART>;
137 gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
138 linux,code = <KEY_WPS_BUTTON>;
143 gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
144 linux,code = <KEY_POWER>;
149 compatible = "gpio-leds";
151 /* broadband-* is a single RGB led */
153 label = "bthomehubv5a:red:broadband";
154 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
157 label = "bthomehubv5a:green:broadband";
158 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
160 broadband_blue: broadband-blue {
161 label = "bthomehubv5a:blue:broadband";
162 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
165 /* wireless-* is a single RGB led */
167 label = "bthomehubv5a:red:wireless";
168 gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
171 label = "bthomehubv5a:green:wireless";
172 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
174 wireless_blue: wireless-blue {
175 label = "bthomehubv5a:blue:wireless";
176 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
179 /* power-* is a single RGB led */
180 power_red: power-red {
181 label = "bthomehubv5a:red:power";
182 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
184 power_green: power-green {
185 label = "bthomehubv5a:green:power";
186 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
187 default-state = "keep";
189 power_blue: power-blue {
190 label = "bthomehubv5a:blue:power";
191 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
196 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
203 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
206 compatible = "pci168c,002d";
207 reg = <0x7000 0 0 0 0>;
208 qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
215 compatible = "lantiq,xrx200-pdi";
216 #address-cells = <1>;
219 mtd-mac-address = <&caldata 0x110c>;
223 compatible = "lantiq,xrx200-pdi-port";
226 phy-handle = <&phy0>;
229 compatible = "lantiq,xrx200-pdi-port";
232 phy-handle = <&phy1>;
235 compatible = "lantiq,xrx200-pdi-port";
238 phy-handle = <&phy11>;
241 compatible = "lantiq,xrx200-pdi-port";
244 phy-handle = <&phy13>;
249 compatible = "lantiq,xrx200-pdi";
250 #address-cells = <1>;
253 mtd-mac-address = <&caldata 0x110c>;
254 mtd-mac-address-increment = <4>;
258 compatible = "lantiq,xrx200-pdi-port";
261 phy-handle = <&phy5>;
266 #address-cells = <1>;
268 compatible = "lantiq,xrx200-mdio";
270 phy0: ethernet-phy@0 {
272 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
274 phy1: ethernet-phy@1 {
276 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
278 phy5: ethernet-phy@5 {
280 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
282 phy11: ethernet-phy@11 {
284 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
286 phy13: ethernet-phy@13 {
288 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";