6 model = "BTHOMEHUBV5A - BT Home Hub 5A";
9 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
13 reg = <0x0 0x8000000>;
19 compatible = "gen_nand", "lantiq,nand-xway";
22 reg = <0 0x0 0x2000000>;
33 reg = <0x40000 0x40000>;
35 caldata: partition@80000 {
37 reg = <0x80000 0x20000>;
42 reg = <0xa0000 0x200000>;
46 reg = <0x2a0000 0x7d60000>;
51 gpio: pinmux@E100B10 {
52 pinctrl-names = "default";
53 pinctrl-0 = <&state_default>;
55 interrupt-parent = <&icu0>;
56 interrupts = <166 135 66 40 41 42 38>;
58 state_default: pinmux {
60 lantiq,groups = "mdio";
61 lantiq,function = "mdio";
77 lantiq,open-drain = <0>;
81 lantiq,groups = "nand cle", "nand ale";
82 lantiq,function = "ebu";
84 lantiq,open-drain = <0>;
88 lantiq,groups = "nand cs1";
89 lantiq,function = "ebu";
90 lantiq,open-drain = <0>;
99 compatible = "lantiq,xrx200-net";
100 reg = < 0xE108000 0x3000 /* switch */
101 0xE10B100 0x70 /* mdio */
102 0xE10B1D8 0x30 /* mii */
103 0xE10B308 0x30 >; /* pmac */
104 interrupt-parent = <&icu0>;
105 interrupts = <73 72>;
108 compatible = "lantiq,xrx200-pdi";
109 #address-cells = <1>;
112 mtd-mac-address = <&caldata 0x110c>;
116 compatible = "lantiq,xrx200-pdi-port";
119 phy-handle = <&phy0>;
122 compatible = "lantiq,xrx200-pdi-port";
125 phy-handle = <&phy1>;
128 compatible = "lantiq,xrx200-pdi-port";
131 phy-handle = <&phy11>;
134 compatible = "lantiq,xrx200-pdi-port";
137 phy-handle = <&phy13>;
142 compatible = "lantiq,xrx200-pdi";
143 #address-cells = <1>;
146 mtd-mac-address = <&caldata 0x110c>;
147 mtd-mac-address-increment = <4>;
151 compatible = "lantiq,xrx200-pdi-port";
154 phy-handle = <&phy5>;
159 #address-cells = <1>;
161 compatible = "lantiq,xrx200-mdio";
163 phy0: ethernet-phy@0 {
165 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
167 phy1: ethernet-phy@1 {
169 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
171 phy5: ethernet-phy@5 {
173 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
175 phy11: ethernet-phy@11 {
177 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
179 phy13: ethernet-phy@13 {
181 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
188 gpios = <&gpio 33 0>;
193 lantiq,bus-clock = <33333333>;
194 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
195 interrupt-map = <0x7000 0 0 1 &icu0 30 1>;
196 gpio-reset = <&gpio 21 0>;
201 compatible = "lantiq,phy-xrx200";
202 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
203 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
208 compatible = "ath9k,eeprom";
209 ath,eep-flash = <&caldata 0x1000>;
210 ath,mac-offset = <0x110c>;
211 ath,mac-increment = <2>;
212 ath,pci-slot = <0xe>; /* 14 */
216 compatible = "gpio-keys-polled";
217 #address-cells = <1>;
219 poll-interval = <100>;
224 linux,code = <0x198>;
229 gpios = <&gpio 25 1>;
230 linux,code = <0x211>;
235 gpios = <&gpio 39 1>;
236 linux,code = <0x198>;
241 compatible = "gpio-leds";
244 label = "soc:red:broadband";
248 label = "soc:green:broadband";
252 label = "soc:blue:broadband";
257 label = "soc:red:wireless";
261 label = "soc:green:wireless";
262 gpios = <&gpio 10 1>;
265 label = "soc:blue:wireless";
266 gpios = <&gpio 11 1>;
270 label = "soc:red:power";
271 gpios = <&gpio 12 1>;
274 label = "soc:green:power";
275 gpios = <&gpio 14 1>;
278 label = "soc:blue:power";
279 gpios = <&gpio 15 1>;
284 gpios = <&gpio 19 0>;