5 #include <dt-bindings/input/input.h>
8 model = "FRITZ7360SL - 1&1 HomeServer";
11 led-boot = &power_green;
12 led-failsafe = &power_red;
13 led-running = &power_green;
15 led-internet = &info_green;
16 led-dsl = &power_green;
21 reg = <0x0 0x8000000>;
27 compatible = "lantiq,nor";
29 reg = <0 0x0 0x1000000>;
33 compatible = "fixed-partitions";
36 urlader: partition@0 {
38 reg = <0x00000 0x20000>;
44 reg = <0x20000 0xf60000>;
49 reg = <0xf80000 0x40000>;
55 reg = <0xfc0000 0x40000>;
62 gpio: pinmux@E100B10 {
63 pinctrl-names = "default";
64 pinctrl-0 = <&state_default>;
66 state_default: pinmux {
68 lantiq,groups = "mdio";
69 lantiq,function = "mdio";
72 lantiq,pins = "io37", "io44";
87 lantiq,portmask = <0x3>;
96 compatible = "lantiq,phy-xrx200";
97 firmware = "lantiq/vr9_phy11g_a2x.bin";
102 compatible = "gpio-keys-polled";
103 #address-cells = <1>;
105 poll-interval = <100>;
108 gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
109 linux,code = <KEY_PHONE>;
113 gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
114 linux,code = <KEY_WLAN>;
119 compatible = "gpio-leds";
122 label = "fritz7360sl:green:power";
123 gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
124 default-state = "keep";
127 label = "fritz7360sl:red:power";
128 gpios = <&gpio 33 GPIO_ACTIVE_LOW>;
131 label = "fritz7360sl:red:info";
132 gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
134 info_green: info_green {
135 label = "fritz7360sl:green:info";
136 gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
139 label = "fritz7360sl:green:wlan";
140 gpios = <&gpio 36 GPIO_ACTIVE_LOW>;
143 label = "fritz7360sl:green:dect";
144 gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
151 compatible = "lantiq,xrx200-pdi";
152 #address-cells = <1>;
155 mac-address = [ 00 11 22 33 44 55 ];
159 compatible = "lantiq,xrx200-pdi-port";
162 phy-handle = <&phy0>;
165 compatible = "lantiq,xrx200-pdi-port";
168 phy-handle = <&phy1>;
171 compatible = "lantiq,xrx200-pdi-port";
174 phy-handle = <&phy11>;
177 compatible = "lantiq,xrx200-pdi-port";
180 phy-handle = <&phy13>;
185 #address-cells = <1>;
187 compatible = "lantiq,xrx200-mdio";
188 phy0: ethernet-phy@0 {
190 compatible = "ethernet-phy-id004d.d076", "ethernet-phy-ieee802.3-c22";
191 reset-gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
193 phy1: ethernet-phy@1 {
195 compatible = "ethernet-phy-id004d.d076", "ethernet-phy-ieee802.3-c22";
196 reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
198 phy11: ethernet-phy@11 {
200 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
202 phy13: ethernet-phy@13 {
204 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
212 #interrupt-cells = <1>;
214 #address-cells = <3>;
218 compatible = "pci168c,002e";
220 qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */