5 #include <dt-bindings/input/input.h>
8 model = "FRITZ7360SL - 1&1 HomeServer";
11 bootargs = "init=/etc/preinit";
15 led-boot = &power_green;
16 led-failsafe = &power_red;
17 led-running = &power_green;
19 led-internet = &info_green;
20 led-dsl = &power_green;
25 reg = <0x0 0x8000000>;
31 compatible = "lantiq,nor";
33 reg = <0 0x0 0x1000000>;
37 compatible = "fixed-partitions";
40 urlader: partition@0 {
42 reg = <0x00000 0x20000>;
48 reg = <0x20000 0xf60000>;
53 reg = <0xf80000 0x40000>;
59 reg = <0xfc0000 0x40000>;
66 gpio: pinmux@E100B10 {
67 pinctrl-names = "default";
68 pinctrl-0 = <&state_default>;
70 state_default: pinmux {
72 lantiq,groups = "mdio";
73 lantiq,function = "mdio";
76 lantiq,pins = "io37", "io44";
91 lantiq,portmask = <0x3>;
100 compatible = "lantiq,phy-xrx200";
101 firmware = "lantiq/vr9_phy11g_a2x.bin";
106 compatible = "gpio-keys-polled";
107 #address-cells = <1>;
109 poll-interval = <100>;
112 gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
113 linux,code = <KEY_PHONE>;
117 gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
118 linux,code = <KEY_WLAN>;
123 compatible = "gpio-leds";
126 label = "fritz7360sl:green:power";
127 gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
128 default-state = "keep";
131 label = "fritz7360sl:red:power";
132 gpios = <&gpio 33 GPIO_ACTIVE_LOW>;
135 label = "fritz7360sl:red:info";
136 gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
138 info_green: info_green {
139 label = "fritz7360sl:green:info";
140 gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
143 label = "fritz7360sl:green:wlan";
144 gpios = <&gpio 36 GPIO_ACTIVE_LOW>;
147 label = "fritz7360sl:green:dect";
148 gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
155 compatible = "lantiq,xrx200-pdi";
156 #address-cells = <1>;
159 mac-address = [ 00 11 22 33 44 55 ];
163 compatible = "lantiq,xrx200-pdi-port";
166 phy-handle = <&phy0>;
167 // gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
170 compatible = "lantiq,xrx200-pdi-port";
173 phy-handle = <&phy1>;
174 // gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
177 compatible = "lantiq,xrx200-pdi-port";
180 phy-handle = <&phy11>;
183 compatible = "lantiq,xrx200-pdi-port";
186 phy-handle = <&phy13>;
191 #address-cells = <1>;
193 compatible = "lantiq,xrx200-mdio";
194 phy0: ethernet-phy@0 {
196 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
198 phy1: ethernet-phy@1 {
200 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
202 phy11: ethernet-phy@11 {
204 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
206 phy13: ethernet-phy@13 {
208 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
216 #interrupt-cells = <1>;
218 #address-cells = <3>;
222 compatible = "pci168c,002e";
224 qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */