1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
6 #include <dt-bindings/input/input.h>
7 #include <dt-bindings/mips/lantiq_rcu_gphy.h>
10 compatible = "avm,fritz736x", "lantiq,xway", "lantiq,vr9";
13 bootargs = "console=ttyLTQ0,115200";
17 led-boot = &power_green;
18 led-failsafe = &power_red;
19 led-running = &power_green;
20 led-upgrade = &power_red;
22 led-dsl = &info_green;
27 device_type = "memory";
28 reg = <0x0 0x8000000>;
32 compatible = "gpio-keys-polled";
33 poll-interval = <100>;
37 gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
38 linux,code = <KEY_PHONE>;
43 gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
44 linux,code = <KEY_WLAN>;
49 compatible = "gpio-leds";
52 gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
53 default-state = "keep";
57 gpios = <&gpio 33 GPIO_ACTIVE_LOW>;
60 info_green: info_green {
61 gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
65 gpios = <&gpio 36 GPIO_ACTIVE_LOW>;
69 gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
73 gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
80 compatible = "lantiq,xrx200-pdi";
84 mtd-mac-address = <&urlader 0xa91>;
85 mtd-mac-address-increment = <(-2)>;
89 compatible = "lantiq,xrx200-pdi-port";
96 compatible = "lantiq,xrx200-pdi-port";
103 compatible = "lantiq,xrx200-pdi-port";
106 phy-handle = <&phy11>;
110 compatible = "lantiq,xrx200-pdi-port";
113 phy-handle = <&phy13>;
118 #address-cells = <1>;
120 compatible = "lantiq,xrx200-mdio";
122 phy0: ethernet-phy@0 {
124 compatible = "ethernet-phy-ieee802.3-c22";
125 reset-gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
128 phy1: ethernet-phy@1 {
130 compatible = "ethernet-phy-ieee802.3-c22";
131 reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
134 phy11: ethernet-phy@11 {
136 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
139 phy13: ethernet-phy@13 {
141 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
147 lantiq,gphy-mode = <GPHY_MODE_GE>;
151 lantiq,gphy-mode = <GPHY_MODE_GE>;
155 pinctrl-names = "default";
156 pinctrl-0 = <&state_default>;
158 state_default: pinmux {
160 lantiq,groups = "mdio";
161 lantiq,function = "mdio";
165 lantiq,pins = "io37", "io44";
179 #interrupt-cells = <1>;
181 #address-cells = <2>;
185 compatible = "pci168c,002e";
187 qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */