3 #include <dt-bindings/input/input.h>
6 compatible = "arcadyan,arv7519pw", "lantiq,xway", "lantiq,danube";
7 model = "Astoria Networks ARV7519PW";
10 bootargs = "console=ttyLTQ0,115200";
15 led-failsafe = &power2;
20 led-internet = &online;
25 device_type = "memory";
26 reg = <0x0 0x4000000>;
30 compatible = "gpio-keys-polled";
31 poll-interval = <100>;
35 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
36 linux,code = <KEY_RFKILL>;
40 gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
41 linux,code = <KEY_RESTART>;
46 compatible = "gpio-leds";
49 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
50 default-state = "keep";
54 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
58 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
62 gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
66 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
70 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
74 gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
78 gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
82 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
86 gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
90 gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
94 gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
98 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
102 gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
106 gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
110 /* is there another way to "reserve" the GPIO? */
112 compatible = "gpio-export";
116 gpio-export,name = "switch";
117 gpio-export,output = <1>;
118 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
124 pinctrl-names = "default";
125 pinctrl-0 = <&state_default>;
127 state_default: pinmux {
129 lantiq,groups = "ebu cs1";
130 lantiq,function = "ebu";
133 lantiq,pins = "io21";
138 lantiq,pins = "io19";
147 nvmem-cells = <&macaddr_boardconfig_16>;
148 nvmem-cell-names = "mac-address";
153 compatible = "lantiq,nor";
155 reg = <0 0x0 0x2000000>;
158 compatible = "fixed-partitions";
159 #address-cells = <1>;
164 reg = <0x00000 0x40000>;
169 label = "u-boot-env";
170 reg = <0x40000 0x20000>;
175 reg = <0x60000 0xf80000>;
178 boardconfig: partition@fe0000 {
179 label = "board_config";
180 reg = <0xfe0000 0x20000>;
190 pinctrl-0 = <&pci_gnt1_pins>, <&pci_req1_pins>;
191 pinctrl-names = "default";
193 lantiq,external-clock;
194 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
198 compatible = "pci0,0";
199 reg = <0x7000 0 0 0 0>;
200 ralink,mtd-eeprom = <&boardconfig 0x410>;
209 /* warning: passive port only works with active devices */
219 compatible = "nvmem-cells";
220 #address-cells = <1>;
223 macaddr_boardconfig_16: macaddr@16 {