5 #include <dt-bindings/input/input.h>
8 compatible = "arcadyan,arv7519pw", "lantiq,xway", "lantiq,danube";
9 model = "Astoria Networks ARV7519PW";
12 bootargs = "console=ttyLTQ0,115200";
17 led-failsafe = &power2;
21 led-internet = &online;
26 reg = <0x0 0x4000000>;
30 compatible = "gpio-keys-polled";
33 poll-interval = <100>;
37 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
38 linux,code = <KEY_RFKILL>;
42 gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
43 linux,code = <KEY_RESTART>;
48 compatible = "gpio-leds";
51 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
52 default-state = "keep";
56 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
60 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
64 gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
68 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
72 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
76 gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
80 gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
84 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
88 gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
92 gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
96 gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
100 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
104 gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
108 gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
112 /* is there another way to "reserve" the GPIO? */
114 compatible = "gpio-export";
118 gpio-export,name = "switch";
119 gpio-export,output = <1>;
120 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
126 pinctrl-names = "default";
127 pinctrl-0 = <&state_default>;
129 state_default: pinmux {
131 lantiq,groups = "ebu cs1";
132 lantiq,function = "ebu";
135 lantiq,groups = "req1";
136 lantiq,function = "pci";
137 lantiq,open-drain = <1>;
142 lantiq,groups = "gnt1";
143 lantiq,function = "pci";
148 lantiq,pins = "io21";
153 lantiq,pins = "io19";
162 mtd-mac-address = <&boardconfig 0x16>;
167 compatible = "lantiq,nor";
169 reg = <0 0x0 0x2000000>;
170 #address-cells = <1>;
174 compatible = "fixed-partitions";
175 #address-cells = <1>;
180 reg = <0x00000 0x40000>;
186 reg = <0x40000 0x20000>;
191 reg = <0x60000 0xf80000>;
194 boardconfig: partition@fe0000 {
195 label = "board_config";
196 reg = <0xfe0000 0x20000>;
205 lantiq,external-clock;
206 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
210 compatible = "pci0,0";
211 reg = <0x7000 0 0 0 0>;
212 ralink,mtd-eeprom = <&boardconfig 0x410>;
213 ralink,mtd-eeprom-swap;
221 /* warning: passive port only works with active devices */