5 #include <dt-bindings/input/input.h>
8 compatible = "arcadyan,arv7519pw", "lantiq,xway", "lantiq,danube";
9 model = "Astoria Networks ARV7519PW";
12 bootargs = "console=ttyLTQ0,115200";
17 led-failsafe = &power2;
22 led-internet = &online;
27 reg = <0x0 0x4000000>;
31 compatible = "gpio-keys-polled";
34 poll-interval = <100>;
38 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
39 linux,code = <KEY_RFKILL>;
43 gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
44 linux,code = <KEY_RESTART>;
49 compatible = "gpio-leds";
52 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
53 default-state = "keep";
57 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
61 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
65 gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
69 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
73 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
77 gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
81 gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
85 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
89 gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
93 gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
97 gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
101 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
105 gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
109 gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
113 /* is there another way to "reserve" the GPIO? */
115 compatible = "gpio-export";
119 gpio-export,name = "switch";
120 gpio-export,output = <1>;
121 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
127 pinctrl-names = "default";
128 pinctrl-0 = <&state_default>;
130 state_default: pinmux {
132 lantiq,groups = "ebu cs1";
133 lantiq,function = "ebu";
136 lantiq,groups = "req1";
137 lantiq,function = "pci";
138 lantiq,open-drain = <1>;
143 lantiq,groups = "gnt1";
144 lantiq,function = "pci";
149 lantiq,pins = "io21";
154 lantiq,pins = "io19";
163 mtd-mac-address = <&boardconfig 0x16>;
168 compatible = "lantiq,nor";
170 reg = <0 0x0 0x2000000>;
171 #address-cells = <1>;
175 compatible = "fixed-partitions";
176 #address-cells = <1>;
181 reg = <0x00000 0x40000>;
187 reg = <0x40000 0x20000>;
192 reg = <0x60000 0xf80000>;
195 boardconfig: partition@fe0000 {
196 label = "board_config";
197 reg = <0xfe0000 0x20000>;
206 lantiq,external-clock;
207 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
211 compatible = "pci0,0";
212 reg = <0x7000 0 0 0 0>;
213 ralink,mtd-eeprom = <&boardconfig 0x410>;
214 ralink,mtd-eeprom-swap;
222 /* warning: passive port only works with active devices */