1 // SPDX-License-Identifier: GPL-2.0-or-later or MIT
3 #include <dt-bindings/input/input.h>
4 #include <dt-bindings/gpio/gpio.h>
6 /include/ "fsl/p1010si-pre.dtsi"
9 model = "Watchguard Firebox T10";
10 compatible = "watchguard,firebox-t10";
13 bootargs = "console=ttyS0,115200";
14 bootargs-override = "console=ttyS0,115200";
20 led-failsafe = &led_failover;
21 led-running = &led_mode;
22 led-upgrade = &led_attention;
26 device_type = "memory";
30 compatible = "gpio-leds";
32 led_attention: attention_orange {
33 gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
34 label = "orange:attention";
38 gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
42 led_mode: mode_green {
43 gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
47 led_failover: failover_green {
48 gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
49 label = "green:failover";
54 compatible = "gpio-keys";
57 label = "Reset button";
58 gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
59 linux,code = <KEY_RESTART>;
65 ranges = <0x0 0x0 0xffe00000 0x100000>;
69 compatible = "sii,s35390a";
76 compatible = "jedec,spi-nor";
78 spi-max-frequency = <25000000>;
81 compatible = "fixed-partitions";
92 reg = <0x90000 0x10000>;
97 reg = <0xa0000 0x20000>;
103 reg = <0xc0000 0x40000>;
111 gpio0: gpio-controller@fc00 {
120 phy1: ethernet-phy@1 {
124 phy2: ethernet-phy@2 {
128 phy3: ethernet-phy@3 {
134 tbi_phy1: tbi-phy@11 {
136 device_type = "tbi-phy";
141 tbi_phy2: tbi-phy@11 {
143 device_type = "tbi-phy";
147 enet0: ethernet@b0000 {
148 phy-handle = <&phy1>;
149 phy-connection-type = "rgmii-id";
152 enet1: ethernet@b1000 {
153 tbi-handle = <&tbi_phy1>;
154 phy-handle = <&phy2>;
155 phy-connection-type = "sgmii";
158 enet2: ethernet@b2000 {
159 tbi-handle = <&tbi_phy2>;
160 phy-handle = <&phy3>;
161 phy-connection-type = "sgmii";
168 serial1: serial@4600 {
181 pci0: pcie@ffe09000 {
185 pci1: pcie@ffe0a000 {
190 reg = <0x0 0xffe1e000 0 0x2000>;
192 /* NOR, NAND Flashes and CPLD on board */
193 ranges = <0x0 0x0 0x0 0xee000000 0x02000000
194 0x1 0x0 0x0 0xff800000 0x00010000
195 0x3 0x0 0x0 0xffb00000 0x00000020>;
198 compatible = "fsl,ifc-nand";
199 reg = <0x1 0x0 0x10000>;
202 compatible = "fixed-partitions";
203 #address-cells = <1>;
207 * Original partition layout:
208 * 0x000000000000-0x000000020000 : "NAND (RW) WG DTB Image"
209 * 0x000000020000-0x000000520000 : "NAND (RW) WG SYSA Kernel"
210 * 0x000000520000-0x000007f00000 : "NAND (RW) WG SYSA_CODE"
211 * 0x000007f00000-0x000008400000 : "NAND (RW) WG SYSB Kernel"
212 * 0x000008400000-0x000009c00000 : "NAND (RW) WG SYSB_CODE"
213 * 0x000009c00000-0x00000a100000 : "NAND (RW) WG SYSA2 Kernel"
214 * 0x00000a100000-0x000011ae0000 : "NAND (RW) WG SYSA_CODE2"
215 * 0x000011ae0000-0x000020000000 : "NAND (RW) WG SYSA_DATA"
225 reg = <0x20000 0x500000>;
230 reg = <0x520000 0x79e0000>;
231 label = "wg-sysa-rootfs";
236 reg = <0x7f00000 0x500000>;
237 label = "wg-sysb-kernel";
242 reg = <0x8400000 0x1800000>;
243 label = "wg-sysb-rootfs";
248 reg = <0x9c00000 0x500000>;
249 label = "wg-sysa2-kernel";
254 reg = <0xa100000 0x79e0000>;
255 label = "wg-sysa2-rootfs";
260 reg = <0x11ae0000 0xe520000>;
268 /include/ "fsl/p1010si-post.dtsi"