1 // SPDX-License-Identifier: GPL-2.0-or-later or MIT
3 /include/ "fsl/p1020si-pre.dtsi"
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
9 model = "Extreme Networks WS-AP3825i";
10 compatible = "extreme-networks,ws-ap3825i";
15 led-boot = &led_power_green;
16 led-failsafe = &led_power_red;
17 led-running = &led_power_green;
18 led-upgrade = &led_power_red;
22 bootargs-override = "console=ttyS0,115200";
26 device_type = "memory";
30 compatible = "gpio-leds";
33 gpios = <&spi_gpio 3 GPIO_ACTIVE_HIGH>;
34 label = "green:radio1";
35 linux,default-trigger = "phy0tpt";
39 gpios = <&spi_gpio 2 GPIO_ACTIVE_HIGH>;
40 label = "green:radio2";
41 linux,default-trigger = "phy1tpt";
44 led_power_green: power_green {
45 gpios = <&spi_gpio 0 GPIO_ACTIVE_HIGH>;
46 label = "green:power";
49 led_power_red: power_red {
50 gpios = <&spi_gpio 1 GPIO_ACTIVE_HIGH>;
55 gpios = <&spi_gpio 6 GPIO_ACTIVE_HIGH>;
60 gpios = <&spi_gpio 4 GPIO_ACTIVE_HIGH>;
65 gpios = <&spi_gpio 7 GPIO_ACTIVE_HIGH>;
70 gpios = <&spi_gpio 5 GPIO_ACTIVE_HIGH>;
76 compatible = "gpio-keys";
79 label = "Reset button";
80 gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
81 linux,code = <KEY_RESTART>;
85 lbc: localbus@ffe05000 {
86 reg = <0 0xffe05000 0 0x1000>;
87 ranges = <0x0 0x0 0x0 0xec000000 0x4000000>;
92 compatible = "cfi-flash";
93 reg = <0x0 0x0 0x4000000>;
98 compatible = "fixed-partitions";
103 compatible = "denx,fit";
104 reg = <0x0 0x3d60000>;
109 reg = <0x3d60000 0x20000>;
115 reg = <0x3d80000 0x80000>;
121 reg = <0x3e00000 0x100000>;
127 reg = <0x3f00000 0x20000>;
132 reg = <0x3f20000 0x20000>;
140 ranges = <0x0 0x0 0xffe00000 0x100000>;
142 gpio0: gpio-controller@fc00 {
146 phy0: ethernet-phy@0 {
147 interrupts = <3 1 0 0>;
149 reset-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
150 reset-assert-us = <10000>;
151 reset-deassert-us = <10000>;
154 phy2: ethernet-phy@2 {
155 interrupts = <1 1 0 0>;
157 reset-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
158 reset-assert-us = <10000>;
159 reset-deassert-us = <10000>;
171 enet0: ethernet@b0000 {
173 phy-handle = <&phy0>;
174 phy-connection-type = "rgmii-id";
177 enet1: ethernet@b1000 {
181 enet2: ethernet@b2000 {
183 phy-handle = <&phy2>;
184 phy-connection-type = "rgmii-id";
197 pci0: pcie@ffe09000 {
198 ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
199 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
200 reg = <0 0xffe09000 0 0x1000>;
202 ranges = <0x2000000 0x0 0xa0000000
203 0x2000000 0x0 0xa0000000
212 pci1: pcie@ffe0a000 {
213 reg = <0 0xffe0a000 0 0x1000>;
214 ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
215 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
217 ranges = <0x2000000 0x0 0x80000000
218 0x2000000 0x0 0x80000000
231 * This is currently non-functioning because the spi-gpio
232 * driver refuses to register when presented with this node.
234 compatible = "spi-gpio";
235 #address-cells = <1>;
238 sck-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
239 mosi-gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
240 num-chipselects = <0>;
242 spi_gpio: led_gpio@0 {
243 compatible = "fairchild,74hc595";
247 registers-number = <1>;
248 spi-max-frequency = <100000>;
253 /include/ "fsl/p1020si-post.dtsi"
258 bus-frequency = <399999996>;
259 timebase-frequency = <50000000>;
260 clock-frequency = <799999992>;
261 d-cache-block-size = <0x20>;
262 d-cache-size = <0x8000>;
263 d-cache-sets = <0x80>;
264 i-cache-block-size = <0x20>;
265 i-cache-size = <0x8000>;
266 i-cache-sets = <0x80>;
270 bus-frequency = <399999996>;
271 timebase-frequency = <50000000>;
272 clock-frequency = <799999992>;
273 d-cache-block-size = <0x20>;
274 d-cache-size = <0x8000>;
275 d-cache-sets = <0x80>;
276 i-cache-block-size = <0x20>;
277 i-cache-size = <0x8000>;
278 i-cache-sets = <0x80>;
283 reg = <0x0 0x0 0x0 0x10000000>;
287 bus-frequency = <399999996>;
290 clock-frequency = <399999996>;
294 clock-frequency = <399999996>;
298 clock-frequency = <399999996>;
304 * For the OpenWrt 22.03 release, since Linux 5.10.138 now uses
305 * aliases to determine PCI domain numbers, drop aliases so as not to
306 * change the sysfs path of our wireless netdevs.
311 /delete-property/ pci0;
312 /delete-property/ pci1;