target/linux/sunxi/patches-3.14/232-2-dt-sun7i-add-bluetooth-to-cubietruck.patch

   1 From 7ed66f828ad1ae46226ad7c1b56466d5ae6d67b9 Mon Sep 17 00:00:00 2001
   2 From: Chen-Yu Tsai <wens@csie.org>
   3 Date: Thu, 26 Dec 2013 17:15:47 +0800
   4 Subject: [PATCH] ARM: dts: sun7i: add bluetooth module to CubieTruck DTS
   5
   6 The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The
   7 Bluetooth part is a BCM20710 IC connected to UART2 in the A20
   8 SoC. The IC also takes a 32.768 KHz low power clock input, a power
   9 enable signal and a wake signal via GPIO.
  10
  11 The Bluetooth module supports out-of-band interrupt signaling via
  12 GPIO, but this is not supported in this patch.
  13 ---
  14  arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 36 ++++++++++++++++++++++++++++++
  15  1 file changed, 36 insertions(+)
  16
  17 diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
  18 index 2444806..9a127d1 100644
  19 --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
  20 +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
  21 @@ -105,6 +105,20 @@
  22                                 allwinner,drive = <0>;
  23                                 allwinner,pull = <0>;
  24                         };
  25 +
  26 +                       bt_pwr_pin: bt_pwr_pin@0 {
  27 +                               allwinner,pins = "PH18";
  28 +                               allwinner,function = "gpio_out";
  29 +                               allwinner,drive = <0>;
  30 +                               allwinner,pull = <0>;
  31 +                       };
  32 +
  33 +                       bt_wake_pin: bt_wake_pin@0 {
  34 +                               allwinner,pins = "PH24";
  35 +                               allwinner,function = "gpio_out";
  36 +                               allwinner,drive = <0>;
  37 +                               allwinner,pull = <0>;
  38 +                       };
  39                 };
  40
  41                 uart0: serial@01c28000 {
  42 @@ -113,6 +127,12 @@
  43                         status = "okay";
  44                 };
  45
  46 +               uart2: serial@01c28800 {
  47 +                       pinctrl-names = "default";
  48 +                       pinctrl-0 = <&uart2_pins_a>;
  49 +                       status = "okay";
  50 +               };
  51 +
  52                 i2c0: i2c@01c2ac00 {
  53                         pinctrl-names = "default";
  54                         pinctrl-0 = <&i2c0_pins_a>;
  55 @@ -194,4 +214,20 @@
  56                 enable-active-high;
  57                 gpio = <&pio 7 9 0>;
  58         };
  59 +
  60 +       rfkill-switches {
  61 +               compatible = "simple-bus";
  62 +               pinctrl-names = "default";
  63 +
  64 +               rfkill_bt {
  65 +                       compatible = "rfkill-gpio";
  66 +                       pinctrl-0 = <&bt_pwr_pin>, <&clk_out_a_pins_a>;
  67 +                       rfkill-name = "bt";
  68 +                       rfkill-type = <2>;
  69 +                       bt_shutdown-gpios = <0>, <&pio 7 18 0>; /* PH18 */
  70 +                       bt_reset-gpios = <&pio 7 24 0>; /* PH24 */
  71 +                       clocks = <&clk_out_a>;
  72 +                       clock-frequency = <32768>;
  73 +               };
  74 +       };
  75  };
  76 --
  77 2.0.3
  78