# replacement for WEXT and its use allows wpa_supplicant to properly control
# the driver to improve existing functionality like roaming and to support new
# functionality.
-CONFIG_DRIVER_WEXT=y
+#CONFIG_DRIVER_WEXT=y
# Driver interface for Linux drivers using the nl80211 kernel interface
CONFIG_DRIVER_NL80211=y
# Driver interface for wired Ethernet drivers
CONFIG_DRIVER_WIRED=y
+# Driver interface for MACsec capable Qualcomm Atheros drivers
+#CONFIG_DRIVER_MACSEC_QCA=y
+
+# Driver interface for Linux MACsec drivers
+#CONFIG_DRIVER_MACSEC_LINUX=y
+
# Driver interface for the Broadcom RoboSwitch family
#CONFIG_DRIVER_ROBOSWITCH=y
#LIBS += -lsocket -ldlpi -lnsl
#LIBS_c += -lsocket
-# Enable IEEE 802.1X Supplicant (automatically included if any EAP method is
-# included)
+# Enable IEEE 802.1X Supplicant (automatically included if any EAP method or
+# MACsec is included)
CONFIG_IEEE8021X_EAPOL=y
# EAP-MD5
# EAP-TLS
CONFIG_EAP_TLS=y
+# Enable EAP-TLSv1.3 support by default (currently disabled unless explicitly
+# enabled in network configuration)
+#CONFIG_EAP_TLSV1_3=y
# EAL-PEAP
CONFIG_EAP_PEAP=y
CONFIG_EAP_TTLS=y
# EAP-FAST
-# Note: If OpenSSL is used as the TLS library, OpenSSL 1.0 or newer is needed
-# for EAP-FAST support. Older OpenSSL releases would need to be patched, e.g.,
-# with openssl-0.9.8x-tls-extensions.patch, to add the needed functions.
CONFIG_EAP_FAST=y
+# EAP-TEAP
+# Note: The current EAP-TEAP implementation is experimental and should not be
+# enabled for production use. The IETF RFC 7170 that defines EAP-TEAP has number
+# of conflicting statements and missing details and the implementation has
+# vendor specific workarounds for those and as such, may not interoperate with
+# any other implementation. This should not be used for anything else than
+# experimentation and interoperability testing until those issues has been
+# resolved.
+#CONFIG_EAP_TEAP=y
+
# EAP-GTC
CONFIG_EAP_GTC=y
# EAP-SIM (enable CONFIG_PCSC, if EAP-SIM is used)
#CONFIG_EAP_SIM=y
+# Enable SIM simulator (Milenage) for EAP-SIM
+#CONFIG_SIM_SIMULATOR=y
+
# EAP-PSK (experimental; this is _not_ needed for WPA-PSK)
#CONFIG_EAP_PSK=y
# EAP-EKE
#CONFIG_EAP_EKE=y
+# MACsec
+#CONFIG_MACSEC=y
+
# PKCS#12 (PFX) support (used to read private key and certificate file from
# a file that usually has extension .p12 or .pfx)
CONFIG_PKCS12=y
# Support VHT overrides (disable VHT, mask MCS rates, etc.)
CONFIG_VHT_OVERRIDES=y
+# Support HE overrides
+CONFIG_HE_OVERRIDES=y
+
# Development testing
#CONFIG_EAPOL_TEST=y
# wpa_passphrase). This saves about 0.5 kB in code size.
#CONFIG_NO_WPA_PASSPHRASE=y
-# Disable scan result processing (ap_mode=1) to save code size by about 1 kB.
+# Simultaneous Authentication of Equals (SAE), WPA3-Personal
+#CONFIG_SAE=y
+
+# SAE Public Key, WPA3-Personal
+#CONFIG_SAE_PK=y
+
+# Disable scan result processing (ap_scan=1) to save code size by about 1 kB.
# This can be used if ap_scan=1 mode is never enabled.
#CONFIG_NO_SCAN_PROCESSING=y
#CONFIG_ELOOP_POLL=y
# Should we use epoll instead of select? Select is used by default.
-#CONFIG_ELOOP_EPOLL=y
+CONFIG_ELOOP_EPOLL=y
# Should we use kqueue instead of select? Select is used by default.
#CONFIG_ELOOP_KQUEUE=y
# in a bridge for EAPOL frames. This should be uncommented only if the kernel
# is known to not have the regression issue in packet socket behavior with
# bridge interfaces (commit 'bridge: respect RFC2863 operational state')').
-#CONFIG_NO_LINUX_PACKET_SOCKET_WAR=y
-
-# PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
-CONFIG_PEERKEY=y
+CONFIG_NO_LINUX_PACKET_SOCKET_WAR=y
-# IEEE 802.11w (management frame protection), also known as PMF
-# Driver support is also needed for IEEE 802.11w.
-CONFIG_IEEE80211W=y
+# Support Operating Channel Validation
+#CONFIG_OCV=y
# Select TLS implementation
# openssl = OpenSSL (default)
#CONFIG_NDIS_EVENTS_INTEGRATED=y
#PLATFORMSDKLIB="/opt/Program Files/Microsoft Platform SDK/Lib"
-# Add support for old DBus control interface
-# (fi.epitest.hostap.WPASupplicant)
-#CONFIG_CTRL_IFACE_DBUS=y
-
# Add support for new DBus control interface
-# (fi.w1.hostap.wpa_supplicant1)
+# (fi.w1.wpa_supplicant1)
#CONFIG_CTRL_IFACE_DBUS_NEW=y
# Add introspection support for new DBus control interface
# IEEE Std 802.11r-2008 (Fast BSS Transition) for station mode
#CONFIG_IEEE80211R=y
-# IEEE Std 802.11r-2008 (Fast BSS Transition) for AP mode (implies
-# CONFIG_IEEE80211R).
-#CONFIG_IEEE80211R_AP=y
-
# Add support for writing debug log to a file (/tmp/wpa_supplicant-log-#.txt)
#CONFIG_DEBUG_FILE=y
# Send debug messages to syslog instead of stdout
-#CONFIG_DEBUG_SYSLOG=y
+CONFIG_DEBUG_SYSLOG=y
# Set syslog facility for debug messages
-#CONFIG_DEBUG_SYSLOG_FACILITY=LOG_DAEMON
+CONFIG_DEBUG_SYSLOG_FACILITY=LOG_DAEMON
# Add support for sending all debug messages (regardless of debug verbosity)
# to the Linux kernel tracing facility. This helps debug the entire stack by
# that meet the requirements described above.
CONFIG_NO_RANDOM_POOL=y
-# IEEE 802.11n (High Throughput) support (mainly for AP mode)
-#CONFIG_IEEE80211N=y
+# Should we attempt to use the getrandom(2) call that provides more reliable
+# yet secure randomness source than /dev/random on Linux 3.17 and newer.
+# Requires glibc 2.25 to build, falls back to /dev/random if unavailable.
+CONFIG_GETRANDOM=y
# IEEE 802.11ac (Very High Throughput) support (mainly for AP mode)
-# (depends on CONFIG_IEEE80211N)
#CONFIG_IEEE80211AC=y
+# IEEE 802.11ax HE support (mainly for AP mode)
+#CONFIG_IEEE80211AX=y
+
+# IEEE 802.11be EHT support (mainly for AP mode)
+# CONFIG_IEEE80211AX is mandatory for setting CONFIG_IEEE80211BE.
+# Note: This is experimental and work in progress. The definitions are still
+# subject to change and this should not be expected to interoperate with the
+# final IEEE 802.11be version.
+#CONFIG_IEEE80211BE=y
+
# Wireless Network Management (IEEE Std 802.11v-2011)
# Note: This is experimental and not complete implementation.
#CONFIG_WNM=y
# Enable TDLS support
#CONFIG_TDLS=y
-# Wi-Fi Direct
-# This can be used to enable Wi-Fi Direct extensions for P2P using an external
+# Wi-Fi Display
+# This can be used to enable Wi-Fi Display extensions for P2P using an external
# program to control the additional information exchanges in the messages.
#CONFIG_WIFI_DISPLAY=y
#
# External password backend for testing purposes (developer use)
#CONFIG_EXT_PASSWORD_TEST=y
+# File-based backend to read passwords from an external file.
+#CONFIG_EXT_PASSWORD_FILE=y
# Enable Fast Session Transfer (FST)
#CONFIG_FST=y
#CONFIG_MBO=y
# Fast Initial Link Setup (FILS) (IEEE 802.11ai)
-# Note: This is an experimental and not yet complete implementation. This
-# should not be enabled for production use.
-#CONFIG_FILS=y
+CONFIG_FILS=y
# FILS shared key authentication with PFS
#CONFIG_FILS_SK_PFS=y
# Opportunistic Wireless Encryption (OWE)
# Experimental implementation of draft-harkins-owe-07.txt
#CONFIG_OWE=y
+
+# Device Provisioning Protocol (DPP) (also known as Wi-Fi Easy Connect)
+#CONFIG_DPP=y
+# DPP version 2 support
+#CONFIG_DPP2=y
+# DPP version 3 support (experimental and still changing; do not enable for
+# production use)
+#CONFIG_DPP3=y
+
+# Wired equivalent privacy (WEP)
+# WEP is an obsolete cryptographic data confidentiality algorithm that is not
+# considered secure. It should not be used for anything anymore. The
+# functionality needed to use WEP is available in the current wpa_supplicant
+# release under this optional build parameter. This functionality is subject to
+# be completely removed in a future release.
+#CONFIG_WEP=y
+
+# Remove all TKIP functionality
+# TKIP is an old cryptographic data confidentiality algorithm that is not
+# considered secure. It should not be used anymore for anything else than a
+# backwards compatibility option as a group cipher when connecting to APs that
+# use WPA+WPA2 mixed mode. For now, the default wpa_supplicant build includes
+# support for this by default, but that functionality is subject to be removed
+# in the future.
+#CONFIG_NO_TKIP=y
+
+# Pre-Association Security Negotiation (PASN)
+# Experimental implementation based on IEEE P802.11z/D2.6 and the protocol
+# design is still subject to change. As such, this should not yet be enabled in
+# production use.
+#CONFIG_PASN=y
+
+# uBus IPC/RPC System
+# Services can connect to the bus and provide methods
+# that can be called by other services or clients.
+CONFIG_UBUS=y
+
+# OpenWrt patch 380-disable-ctrl-iface-mib.patch
+# leads to the MIB only being compiled in if
+# CONFIG_CTRL_IFACE_MIB is enabled.
+CONFIG_CTRL_IFACE_MIB=y
projects / openwrt / staging / xback.git / blobdiff