no_device=1
proto_config_add_string "device:device"
proto_config_add_string apn
+ proto_config_add_string v6apn
proto_config_add_string auth
proto_config_add_string username
proto_config_add_string password
proto_config_add_string modes
proto_config_add_string pdptype
proto_config_add_int profile
+ proto_config_add_int v6profile
+ proto_config_add_boolean dhcp
proto_config_add_boolean dhcpv6
proto_config_add_boolean autoconnect
proto_config_add_int plmn
+ proto_config_add_int timeout
+ proto_config_add_int mtu
proto_config_add_defaults
}
proto_qmi_setup() {
local interface="$1"
- local dataformat connstat
- local device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn $PROTO_DEFAULT_OPTIONS
+ local dataformat connstat plmn_mode mcc mnc
+ local device apn v6apn auth username password pincode delay modes pdptype
+ local profile v6profile dhcp dhcpv6 autoconnect plmn timeout mtu $PROTO_DEFAULT_OPTIONS
local ip4table ip6table
local cid_4 pdh_4 cid_6 pdh_6
local ip_6 ip_prefix_length gateway_6 dns1_6 dns2_6
- json_get_vars device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn ip4table ip6table $PROTO_DEFAULT_OPTIONS
+
+ json_get_vars device apn v6apn auth username password pincode delay modes
+ json_get_vars pdptype profile v6profile dhcp dhcpv6 autoconnect plmn ip4table
+ json_get_vars ip6table timeout mtu $PROTO_DEFAULT_OPTIONS
+
+ [ "$timeout" = "" ] && timeout="10"
[ "$metric" = "" ] && metric="0"
return 1
}
+ [ -n "$mtu" ] && {
+ echo "Setting MTU to $mtu"
+ /sbin/ip link set dev $ifname mtu $mtu
+ }
+
+ echo "Waiting for SIM initialization"
+ local uninitialized_timeout=0
+ # timeout 3s for first call to avoid hanging uqmi
+ uqmi -d "$device" --get-pin-status -t 3000 > /dev/null 2>&1
while uqmi -s -d "$device" --get-pin-status | grep '"UIM uninitialized"' > /dev/null; do
[ -e "$device" ] || return 1
- sleep 1;
+ if [ "$uninitialized_timeout" -lt "$timeout" -o "$timeout" = "0" ]; then
+ let uninitialized_timeout++
+ sleep 1;
+ else
+ echo "SIM not initialized"
+ proto_notify_error "$interface" SIM_NOT_INITIALIZED
+ proto_block_restart "$interface"
+ return 1
+ fi
done
- [ -n "$pincode" ] && {
- uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null || {
- echo "Unable to verify PIN"
- proto_notify_error "$interface" PIN_FAILED
+ # Check if UIM application is stuck in illegal state
+ local uim_state_timeout=0
+ while true; do
+ json_load "$(uqmi -s -d "$device" --uim-get-sim-state)"
+ json_get_var card_application_state card_application_state
+
+ # SIM card is either completely absent or state is labeled as illegal
+ # Try to power-cycle the SIM card to recover from this state
+ if [ -z "$card_application_state" -o "$card_application_state" = "illegal" ]; then
+ echo "SIM in illegal state - Power-cycling SIM"
+
+ # Try to reset SIM application
+ uqmi -d "$device" --uim-power-off --uim-slot 1
+ sleep 3
+ uqmi -d "$device" --uim-power-on --uim-slot 1
+
+ if [ "$uim_state_timeout" -lt "$timeout" ] || [ "$timeout" = "0" ]; then
+ let uim_state_timeout++
+ sleep 1
+ continue
+ fi
+
+ # Recovery failed
+ proto_notify_error "$interface" SIM_ILLEGAL_STATE
proto_block_restart "$interface"
return 1
+ else
+ break
+ fi
+ done
+
+ if uqmi -s -d "$device" --uim-get-sim-state | grep -q '"Not supported"\|"Invalid QMI command"' &&
+ uqmi -s -d "$device" --get-pin-status | grep -q '"Not supported"\|"Invalid QMI command"' ; then
+ [ -n "$pincode" ] && {
+ uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null || {
+ echo "Unable to verify PIN"
+ proto_notify_error "$interface" PIN_FAILED
+ proto_block_restart "$interface"
+ return 1
+ }
}
- }
+ else
+ json_load "$(uqmi -s -d "$device" --get-pin-status)"
+ json_get_var pin1_status pin1_status
+ if [ -z "$pin1_status" ]; then
+ json_load "$(uqmi -s -d "$device" --uim-get-sim-state)"
+ json_get_var pin1_status pin1_status
+ fi
+ json_get_var pin1_verify_tries pin1_verify_tries
+
+ case "$pin1_status" in
+ disabled)
+ echo "PIN verification is disabled"
+ ;;
+ blocked)
+ echo "SIM locked PUK required"
+ proto_notify_error "$interface" PUK_NEEDED
+ proto_block_restart "$interface"
+ return 1
+ ;;
+ not_verified)
+ [ "$pin1_verify_tries" -lt "3" ] && {
+ echo "PIN verify count value is $pin1_verify_tries this is below the limit of 3"
+ proto_notify_error "$interface" PIN_TRIES_BELOW_LIMIT
+ proto_block_restart "$interface"
+ return 1
+ }
+ if [ -n "$pincode" ]; then
+ uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null 2>&1 || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null 2>&1 || {
+ echo "Unable to verify PIN"
+ proto_notify_error "$interface" PIN_FAILED
+ proto_block_restart "$interface"
+ return 1
+ }
+ else
+ echo "PIN not specified but required"
+ proto_notify_error "$interface" PIN_NOT_SPECIFIED
+ proto_block_restart "$interface"
+ return 1
+ fi
+ ;;
+ verified)
+ echo "PIN already verified"
+ ;;
+ *)
+ echo "PIN status failed (${pin1_status:-sim_not_present})"
+ proto_notify_error "$interface" PIN_STATUS_FAILED
+ proto_block_restart "$interface"
+ return 1
+ ;;
+ esac
+ json_cleanup
+ fi
- [ -n "$plmn" ] && {
- local mcc mnc
- if [ "$plmn" = 0 ]; then
+ if [ -n "$plmn" ]; then
+ json_load "$(uqmi -s -d "$device" --get-plmn)"
+ json_get_var plmn_mode mode
+ json_get_vars mcc mnc || {
mcc=0
mnc=0
- echo "Setting PLMN to auto"
- else
+ }
+
+ if [ "$plmn" = "0" ]; then
+ if [ "$plmn_mode" != "automatic" ]; then
+ mcc=0
+ mnc=0
+ echo "Setting PLMN to auto"
+ fi
+ elif [ "$mcc" -ne "${plmn:0:3}" -o "$mnc" -ne "${plmn:3}" ]; then
mcc=${plmn:0:3}
mnc=${plmn:3}
echo "Setting PLMN to $plmn"
+ else
+ mcc=""
+ mnc=""
fi
- uqmi -s -d "$device" --set-plmn --mcc "$mcc" --mnc "$mnc" || {
+ fi
+
+ if [ -n "$mcc" -a -n "$mnc" ]; then
+ uqmi -s -d "$device" --set-plmn --mcc "$mcc" --mnc "$mnc" > /dev/null 2>&1 || {
echo "Unable to set PLMN"
proto_notify_error "$interface" PLMN_FAILED
proto_block_restart "$interface"
return 1
}
- }
+ fi
# Cleanup current state if any
- uqmi -s -d "$device" --stop-network 0xffffffff --autoconnect
+ uqmi -s -d "$device" --stop-network 0xffffffff --autoconnect > /dev/null 2>&1
+ uqmi -s -d "$device" --set-ip-family ipv6 --stop-network 0xffffffff --autoconnect > /dev/null 2>&1
+
+ # Go online
+ uqmi -s -d "$device" --set-device-operating-mode online > /dev/null 2>&1
# Set IP format
- uqmi -s -d "$device" --set-data-format 802.3
- uqmi -s -d "$device" --wda-set-data-format 802.3
+ uqmi -s -d "$device" --set-data-format 802.3 > /dev/null 2>&1
+ uqmi -s -d "$device" --wda-set-data-format 802.3 > /dev/null 2>&1
dataformat="$(uqmi -s -d "$device" --wda-get-data-format)"
if [ "$dataformat" = '"raw-ip"' ]; then
echo "Y" > /sys/class/net/$ifname/qmi/raw_ip
fi
- uqmi -s -d "$device" --sync
+ uqmi -s -d "$device" --sync > /dev/null 2>&1
+
+ uqmi -s -d "$device" --network-register > /dev/null 2>&1
echo "Waiting for network registration"
- while uqmi -s -d "$device" --get-serving-system | grep '"searching"' > /dev/null; do
- [ -e "$device" ] || return 1
- sleep 5;
+ sleep 1
+ local registration_timeout=0
+ local registration_state=""
+ while true; do
+ registration_state=$(uqmi -s -d "$device" --get-serving-system 2>/dev/null | jsonfilter -e "@.registration" 2>/dev/null)
+
+ [ "$registration_state" = "registered" ] && break
+
+ if [ "$registration_state" = "searching" ] || [ "$registration_state" = "not_registered" ]; then
+ if [ "$registration_timeout" -lt "$timeout" ] || [ "$timeout" = "0" ]; then
+ [ "$registration_state" = "searching" ] || {
+ echo "Device stopped network registration. Restart network registration"
+ uqmi -s -d "$device" --network-register > /dev/null 2>&1
+ }
+ let registration_timeout++
+ sleep 1
+ continue
+ fi
+ echo "Network registration failed, registration timeout reached"
+ else
+ # registration_state is 'registration_denied' or 'unknown' or ''
+ echo "Network registration failed (reason: '$registration_state')"
+ fi
+
+ proto_notify_error "$interface" NETWORK_REGISTRATION_FAILED
+ return 1
done
- [ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes"
+ [ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
- pdptype=$(echo "$pdptype" | awk '{print tolower($0)}')
+ pdptype="$(echo "$pdptype" | awk '{print tolower($0)}')"
+
[ "$pdptype" = "ip" -o "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] || pdptype="ip"
if [ "$pdptype" = "ip" ]; then
return 1
fi
- uqmi -s -d "$device" --set-client-id wds,"$cid_4" --set-ip-family ipv4 > /dev/null
+ uqmi -s -d "$device" --set-client-id wds,"$cid_4" --set-ip-family ipv4 > /dev/null 2>&1
pdh_4=$(uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
--start-network \
${password:+--password $password} \
${autoconnect:+--autoconnect})
- # pdh_4 is a numeric value on success
+ # pdh_4 is a numeric value on success
if ! [ "$pdh_4" -eq "$pdh_4" ] 2> /dev/null; then
echo "Unable to connect IPv4"
- uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds
+ uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
fi
- # Check data connection state
- connstat=$(uqmi -s -d "$device" --get-data-status)
- [ "$connstat" == '"connected"' ] || {
- echo "No data link!"
- uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds
- proto_notify_error "$interface" CALL_FAILED
- return 1
- }
+ # Check data connection state
+ connstat=$(uqmi -s -d "$device" --set-client-id wds,"$cid_4" --get-data-status)
+ [ "$connstat" == '"connected"' ] || {
+ echo "No data link!"
+ uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds > /dev/null 2>&1
+ proto_notify_error "$interface" CALL_FAILED
+ return 1
+ }
}
[ "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] && {
return 1
fi
- uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 > /dev/null
+ uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 > /dev/null 2>&1
+
+ : "${v6apn:=${apn}}"
+ : "${v6profile:=${profile}}"
pdh_6=$(uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
--start-network \
- ${apn:+--apn $apn} \
- ${profile:+--profile $profile} \
+ ${v6apn:+--apn $v6apn} \
+ ${v6profile:+--profile $v6profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
${autoconnect:+--autoconnect})
- # pdh_6 is a numeric value on success
+ # pdh_6 is a numeric value on success
if ! [ "$pdh_6" -eq "$pdh_6" ] 2> /dev/null; then
echo "Unable to connect IPv6"
- uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds
+ uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
fi
- # Check data connection state
- connstat=$(uqmi -s -d "$device" --get-data-status)
- [ "$connstat" == '"connected"' ] || {
- echo "No data link!"
- uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds
- proto_notify_error "$interface" CALL_FAILED
- return 1
- }
+ # Check data connection state
+ connstat=$(uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 --get-data-status)
+ [ "$connstat" == '"connected"' ] || {
+ echo "No data link!"
+ uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds > /dev/null 2>&1
+ proto_notify_error "$interface" CALL_FAILED
+ return 1
+ }
}
echo "Setting up $ifname"
}
proto_close_data
proto_send_update "$interface"
+
+ local zone="$(fw3 -q network "$interface" 2>/dev/null)"
+
[ -n "$pdh_6" ] && {
if [ -z "$dhcpv6" -o "$dhcpv6" = 0 ]; then
json_load "$(uqmi -s -d $device --set-client-id wds,$cid_6 --get-current-settings)"
proto_add_dns_server "$dns1_6"
proto_add_dns_server "$dns2_6"
}
+ [ -n "$zone" ] && {
+ proto_add_data
+ json_add_string zone "$zone"
+ proto_close_data
+ }
proto_send_update "$interface"
else
json_init
json_add_string name "${interface}_6"
json_add_string ifname "@$interface"
+ [ "$pdptype" = "ipv4v6" ] && json_add_string iface_464xlat "0"
json_add_string proto "dhcpv6"
[ -n "$ip6table" ] && json_add_string ip6table "$ip6table"
proto_add_dynamic_defaults
# RFC 7278: Extend an IPv6 /64 Prefix to LAN
json_add_string extendprefix 1
+ [ -n "$zone" ] && json_add_string zone "$zone"
json_close_object
ubus call network add_dynamic "$(json_dump)"
fi
}
[ -n "$pdh_4" ] && {
- json_init
- json_add_string name "${interface}_4"
- json_add_string ifname "@$interface"
- json_add_string proto "dhcp"
- [ -n "$ip4table" ] && json_add_string ip4table "$ip4table"
- proto_add_dynamic_defaults
- json_close_object
- ubus call network add_dynamic "$(json_dump)"
+ if [ "$dhcp" = 0 ]; then
+ json_load "$(uqmi -s -d $device --set-client-id wds,$cid_4 --get-current-settings)"
+ json_select ipv4
+ json_get_var ip_4 ip
+ json_get_var gateway_4 gateway
+ json_get_var dns1_4 dns1
+ json_get_var dns2_4 dns2
+ json_get_var subnet_4 subnet
+
+ proto_init_update "$ifname" 1
+ proto_set_keep 1
+ proto_add_ipv4_address "$ip_4" "$subnet_4"
+ proto_add_ipv4_route "$gateway_4" "128"
+ [ "$defaultroute" = 0 ] || proto_add_ipv4_route "0.0.0.0" 0 "$gateway_4"
+ [ "$peerdns" = 0 ] || {
+ proto_add_dns_server "$dns1_4"
+ proto_add_dns_server "$dns2_4"
+ }
+ [ -n "$zone" ] && {
+ proto_add_data
+ json_add_string zone "$zone"
+ proto_close_data
+ }
+ proto_send_update "$interface"
+ else
+ json_init
+ json_add_string name "${interface}_4"
+ json_add_string ifname "@$interface"
+ json_add_string proto "dhcp"
+ [ -n "$ip4table" ] && json_add_string ip4table "$ip4table"
+ proto_add_dynamic_defaults
+ [ -n "$zone" ] && json_add_string zone "$zone"
+ json_close_object
+ ubus call network add_dynamic "$(json_dump)"
+ fi
}
}