proto_config_add_boolean dhcpv6
proto_config_add_boolean autoconnect
proto_config_add_int plmn
+ proto_config_add_int timeout
+ proto_config_add_int mtu
proto_config_add_defaults
}
proto_qmi_setup() {
local interface="$1"
-
- local device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn $PROTO_DEFAULT_OPTIONS
+ local dataformat connstat
+ local device apn auth username password pincode delay modes pdptype
+ local profile dhcpv6 autoconnect plmn timeout mtu $PROTO_DEFAULT_OPTIONS
+ local ip4table ip6table
local cid_4 pdh_4 cid_6 pdh_6
local ip_6 ip_prefix_length gateway_6 dns1_6 dns2_6
- json_get_vars device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn $PROTO_DEFAULT_OPTIONS
+
+ json_get_vars device apn auth username password pincode delay modes
+ json_get_vars pdptype profile dhcpv6 autoconnect plmn ip4table
+ json_get_vars ip6table timeout mtu $PROTO_DEFAULT_OPTIONS
+
+ [ "$timeout" = "" ] && timeout="10"
[ "$metric" = "" ] && metric="0"
return 1
}
+ [ -n "$delay" ] && sleep "$delay"
+
device="$(readlink -f $device)"
[ -c "$device" ] || {
echo "The specified control device does not exist"
return 1
}
- [ -n "$delay" ] && sleep "$delay"
+ [ -n "$mtu" ] && {
+ echo "Setting MTU to $mtu"
+ /sbin/ip link set dev $ifname mtu $mtu
+ }
+ echo "Waiting for SIM initialization"
+ local uninitialized_timeout=0
while uqmi -s -d "$device" --get-pin-status | grep '"UIM uninitialized"' > /dev/null; do
- sleep 1;
- done
-
- [ -n "$pincode" ] && {
- uqmi -s -d "$device" --verify-pin1 "$pincode" || {
- echo "Unable to verify PIN"
- proto_notify_error "$interface" PIN_FAILED
+ [ -e "$device" ] || return 1
+ if [ "$uninitialized_timeout" -lt "$timeout" ]; then
+ let uninitialized_timeout++
+ sleep 1;
+ else
+ echo "SIM not initialized"
+ proto_notify_error "$interface" SIM_NOT_INITIALIZED
proto_block_restart "$interface"
return 1
+ fi
+ done
+
+ if uqmi -s -d "$device" --get-pin-status | grep '"Not supported"\|"Invalid QMI command"' > /dev/null; then
+ [ -n "$pincode" ] && {
+ uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null || {
+ echo "Unable to verify PIN"
+ proto_notify_error "$interface" PIN_FAILED
+ proto_block_restart "$interface"
+ return 1
+ }
}
- }
+ else
+ . /usr/share/libubox/jshn.sh
+ json_load "$(uqmi -s -d "$device" --get-pin-status)"
+ json_get_var pin1_status pin1_status
+ json_get_var pin1_verify_tries pin1_verify_tries
+
+ case "$pin1_status" in
+ disabled)
+ echo "PIN verification is disabled"
+ ;;
+ blocked)
+ echo "SIM locked PUK required"
+ proto_notify_error "$interface" PUK_NEEDED
+ proto_block_restart "$interface"
+ return 1
+ ;;
+ not_verified)
+ [ "$pin1_verify_tries" -lt "3" ] && {
+ echo "PIN verify count value is $pin1_verify_tries this is below the limit of 3"
+ proto_notify_error "$interface" PIN_TRIES_BELOW_LIMIT
+ proto_block_restart "$interface"
+ return 1
+ }
+ if [ -n "$pincode" ]; then
+ uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null 2>&1 || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null 2>&1 || {
+ echo "Unable to verify PIN"
+ proto_notify_error "$interface" PIN_FAILED
+ proto_block_restart "$interface"
+ return 1
+ }
+ else
+ echo "PIN not specified but required"
+ proto_notify_error "$interface" PIN_NOT_SPECIFIED
+ proto_block_restart "$interface"
+ return 1
+ fi
+ ;;
+ verified)
+ echo "PIN already verified"
+ ;;
+ *)
+ echo "PIN status failed ($pin1_status)"
+ proto_notify_error "$interface" PIN_STATUS_FAILED
+ proto_block_restart "$interface"
+ return 1
+ ;;
+ esac
+ fi
[ -n "$plmn" ] && {
local mcc mnc
mnc=${plmn:3}
echo "Setting PLMN to $plmn"
fi
- uqmi -s -d "$device" --set-plmn --mcc "$mcc" --mnc "$mnc" || {
+ uqmi -s -d "$device" --set-plmn --mcc "$mcc" --mnc "$mnc" > /dev/null 2>&1 || {
echo "Unable to set PLMN"
proto_notify_error "$interface" PLMN_FAILED
proto_block_restart "$interface"
}
}
- uqmi -s -d "$device" --set-data-format 802.3
- uqmi -s -d "$device" --wda-set-data-format 802.3
- uqmi -s -d "$device" --sync
+ # Cleanup current state if any
+ uqmi -s -d "$device" --stop-network 0xffffffff --autoconnect > /dev/null 2>&1
+
+ # Set IP format
+ uqmi -s -d "$device" --set-data-format 802.3 > /dev/null 2>&1
+ uqmi -s -d "$device" --wda-set-data-format 802.3 > /dev/null 2>&1
+ dataformat="$(uqmi -s -d "$device" --wda-get-data-format)"
+
+ if [ "$dataformat" = '"raw-ip"' ]; then
+
+ [ -f /sys/class/net/$ifname/qmi/raw_ip ] || {
+ echo "Device only supports raw-ip mode but is missing this required driver attribute: /sys/class/net/$ifname/qmi/raw_ip"
+ return 1
+ }
+
+ echo "Device does not support 802.3 mode. Informing driver of raw-ip only for $ifname .."
+ echo "Y" > /sys/class/net/$ifname/qmi/raw_ip
+ fi
+
+ uqmi -s -d "$device" --sync > /dev/null 2>&1
echo "Waiting for network registration"
+ local registration_timeout=0
while uqmi -s -d "$device" --get-serving-system | grep '"searching"' > /dev/null; do
- sleep 5;
+ [ -e "$device" ] || return 1
+ if [ "$registration_timeout" -lt "$timeout" ]; then
+ let registration_timeout++
+ sleep 1;
+ else
+ echo "Network registration failed"
+ proto_notify_error "$interface" NETWORK_REGISTRATION_FAILED
+ proto_block_restart "$interface"
+ return 1
+ fi
done
- [ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes"
+ [ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
- pdptype=`echo "$pdptype" | awk '{print tolower($0)}'`
+ pdptype=$(echo "$pdptype" | awk '{print tolower($0)}')
[ "$pdptype" = "ip" -o "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] || pdptype="ip"
if [ "$pdptype" = "ip" ]; then
fi
[ "$pdptype" = "ip" -o "$pdptype" = "ipv4v6" ] && {
- cid_4=`uqmi -s -d "$device" --get-client-id wds`
- [ $? -ne 0 ] && {
+ cid_4=$(uqmi -s -d "$device" --get-client-id wds)
+ if ! [ "$cid_4" -eq "$cid_4" ] 2> /dev/null; then
echo "Unable to obtain client ID"
proto_notify_error "$interface" NO_CID
return 1
- }
-
- uqmi -s -d "$device" --set-client-id wds,"$cid_4" --set-ip-family ipv4 > /dev/null
+ fi
- # try to clear previous autoconnect state
- uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
- --stop-network 0xffffffff \
- --autoconnect > /dev/null
+ uqmi -s -d "$device" --set-client-id wds,"$cid_4" --set-ip-family ipv4 > /dev/null 2>&1
- pdh_4=`uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
+ pdh_4=$(uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
--start-network \
${apn:+--apn $apn} \
${profile:+--profile $profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
- ${autoconnect:+--autoconnect}`
- [ $? -ne 0 ] && {
+ ${autoconnect:+--autoconnect})
+
+ # pdh_4 is a numeric value on success
+ if ! [ "$pdh_4" -eq "$pdh_4" ] 2> /dev/null; then
echo "Unable to connect IPv4"
- uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds
+ uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds > /dev/null 2>&1
+ proto_notify_error "$interface" CALL_FAILED
+ return 1
+ fi
+
+ # Check data connection state
+ connstat=$(uqmi -s -d "$device" --get-data-status)
+ [ "$connstat" == '"connected"' ] || {
+ echo "No data link!"
+ uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
}
}
[ "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] && {
- cid_6=`uqmi -s -d "$device" --get-client-id wds`
- [ $? -ne 0 ] && {
+ cid_6=$(uqmi -s -d "$device" --get-client-id wds)
+ if ! [ "$cid_6" -eq "$cid_6" ] 2> /dev/null; then
echo "Unable to obtain client ID"
proto_notify_error "$interface" NO_CID
return 1
- }
-
- uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 > /dev/null
+ fi
- # try to clear previous autoconnect state
- uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
- --stop-network 0xffffffff \
- --autoconnect > /dev/null
+ uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 > /dev/null 2>&1
- pdh_6=`uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
+ pdh_6=$(uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
--start-network \
${apn:+--apn $apn} \
${profile:+--profile $profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
- ${autoconnect:+--autoconnect}`
- [ $? -ne 0 ] && {
+ ${autoconnect:+--autoconnect})
+
+ # pdh_6 is a numeric value on success
+ if ! [ "$pdh_6" -eq "$pdh_6" ] 2> /dev/null; then
echo "Unable to connect IPv6"
- uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds
+ uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds > /dev/null 2>&1
+ proto_notify_error "$interface" CALL_FAILED
+ return 1
+ fi
+
+ # Check data connection state
+ connstat=$(uqmi -s -d "$device" --get-data-status)
+ [ "$connstat" == '"connected"' ] || {
+ echo "No data link!"
+ uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
}
}
proto_close_data
proto_send_update "$interface"
+
+ local zone="$(fw3 -q network "$interface" 2>/dev/null)"
+
[ -n "$pdh_6" ] && {
if [ -z "$dhcpv6" -o "$dhcpv6" = 0 ]; then
json_load "$(uqmi -s -d $device --set-client-id wds,$cid_6 --get-current-settings)"
proto_add_dns_server "$dns1_6"
proto_add_dns_server "$dns2_6"
}
+ [ -n "$zone" ] && {
+ proto_add_data
+ json_add_string zone "$zone"
+ proto_close_data
+ }
proto_send_update "$interface"
else
json_init
json_add_string name "${interface}_6"
json_add_string ifname "@$interface"
json_add_string proto "dhcpv6"
+ [ -n "$ip6table" ] && json_add_string ip6table "$ip6table"
proto_add_dynamic_defaults
# RFC 7278: Extend an IPv6 /64 Prefix to LAN
json_add_string extendprefix 1
+ [ -n "$zone" ] && json_add_string zone "$zone"
json_close_object
ubus call network add_dynamic "$(json_dump)"
fi
json_add_string name "${interface}_4"
json_add_string ifname "@$interface"
json_add_string proto "dhcp"
+ [ -n "$ip4table" ] && json_add_string ip4table "$ip4table"
proto_add_dynamic_defaults
+ [ -n "$zone" ] && json_add_string zone "$zone"
json_close_object
ubus call network add_dynamic "$(json_dump)"
}
uqmi -s -d "$device" --set-client-id wds,"$cid" \
--stop-network 0xffffffff \
- --autoconnect > /dev/null
+ --autoconnect > /dev/null 2>&1
- [ -n "$pdh" ] && uqmi -s -d "$device" --set-client-id wds,"$cid" --stop-network "$pdh"
- uqmi -s -d "$device" --set-client-id wds,"$cid" --release-client-id wds
+ [ -n "$pdh" ] && {
+ uqmi -s -d "$device" --set-client-id wds,"$cid" \
+ --stop-network "$pdh" > /dev/null 2>&1
+ }
+
+ uqmi -s -d "$device" --set-client-id wds,"$cid" \
+ --release-client-id wds > /dev/null 2>&1
}
proto_qmi_teardown() {