no_device=1
proto_config_add_string "device:device"
proto_config_add_string apn
+ proto_config_add_string v6apn
proto_config_add_string auth
proto_config_add_string username
proto_config_add_string password
proto_config_add_string modes
proto_config_add_string pdptype
proto_config_add_int profile
+ proto_config_add_int v6profile
+ proto_config_add_boolean dhcp
proto_config_add_boolean dhcpv6
proto_config_add_boolean autoconnect
proto_config_add_int plmn
proto_qmi_setup() {
local interface="$1"
- local dataformat connstat
- local device apn auth username password pincode delay modes pdptype
- local profile dhcpv6 autoconnect plmn timeout mtu $PROTO_DEFAULT_OPTIONS
+ local dataformat connstat plmn_mode mcc mnc
+ local device apn v6apn auth username password pincode delay modes pdptype
+ local profile v6profile dhcp dhcpv6 autoconnect plmn timeout mtu $PROTO_DEFAULT_OPTIONS
local ip4table ip6table
local cid_4 pdh_4 cid_6 pdh_6
local ip_6 ip_prefix_length gateway_6 dns1_6 dns2_6
- json_get_vars device apn auth username password pincode delay modes
- json_get_vars pdptype profile dhcpv6 autoconnect plmn ip4table
+ json_get_vars device apn v6apn auth username password pincode delay modes
+ json_get_vars pdptype profile v6profile dhcp dhcpv6 autoconnect plmn ip4table
json_get_vars ip6table timeout mtu $PROTO_DEFAULT_OPTIONS
[ "$timeout" = "" ] && timeout="10"
echo "Waiting for SIM initialization"
local uninitialized_timeout=0
+ # timeout 3s for first call to avoid hanging uqmi
+ uqmi -d "$device" --get-pin-status -t 3000 > /dev/null 2>&1
while uqmi -s -d "$device" --get-pin-status | grep '"UIM uninitialized"' > /dev/null; do
[ -e "$device" ] || return 1
- if [ "$uninitialized_timeout" -lt "$timeout" ]; then
+ if [ "$uninitialized_timeout" -lt "$timeout" -o "$timeout" = "0" ]; then
let uninitialized_timeout++
sleep 1;
else
fi
done
- if uqmi -s -d "$device" --get-pin-status | grep '"Not supported"\|"Invalid QMI command"' > /dev/null; then
+ if uqmi -s -d "$device" --uim-get-sim-state | grep -q '"Not supported"\|"Invalid QMI command"' &&
+ uqmi -s -d "$device" --get-pin-status | grep -q '"Not supported"\|"Invalid QMI command"' ; then
[ -n "$pincode" ] && {
uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null || {
echo "Unable to verify PIN"
}
}
else
- . /usr/share/libubox/jshn.sh
json_load "$(uqmi -s -d "$device" --get-pin-status)"
json_get_var pin1_status pin1_status
+ if [ -z "$pin1_status" ]; then
+ json_load "$(uqmi -s -d "$device" --uim-get-sim-state)"
+ json_get_var pin1_status pin1_status
+ fi
json_get_var pin1_verify_tries pin1_verify_tries
case "$pin1_status" in
echo "PIN already verified"
;;
*)
- echo "PIN status failed ($pin1_status)"
+ echo "PIN status failed (${pin1_status:-sim_not_present})"
proto_notify_error "$interface" PIN_STATUS_FAILED
proto_block_restart "$interface"
return 1
;;
esac
+ json_cleanup
fi
- [ -n "$plmn" ] && {
- local mcc mnc
- if [ "$plmn" = 0 ]; then
+ if [ -n "$plmn" ]; then
+ json_load "$(uqmi -s -d "$device" --get-plmn)"
+ json_get_var plmn_mode mode
+ json_get_vars mcc mnc || {
mcc=0
mnc=0
- echo "Setting PLMN to auto"
- else
+ }
+
+ if [ "$plmn" = "0" ]; then
+ if [ "$plmn_mode" != "automatic" ]; then
+ mcc=0
+ mnc=0
+ echo "Setting PLMN to auto"
+ fi
+ elif [ "$mcc" -ne "${plmn:0:3}" -o "$mnc" -ne "${plmn:3}" ]; then
mcc=${plmn:0:3}
mnc=${plmn:3}
echo "Setting PLMN to $plmn"
+ else
+ mcc=""
+ mnc=""
fi
+ fi
+
+ if [ -n "$mcc" -a -n "$mnc" ]; then
uqmi -s -d "$device" --set-plmn --mcc "$mcc" --mnc "$mnc" > /dev/null 2>&1 || {
echo "Unable to set PLMN"
proto_notify_error "$interface" PLMN_FAILED
proto_block_restart "$interface"
return 1
}
- }
+ fi
# Cleanup current state if any
uqmi -s -d "$device" --stop-network 0xffffffff --autoconnect > /dev/null 2>&1
+ uqmi -s -d "$device" --set-ip-family ipv6 --stop-network 0xffffffff --autoconnect > /dev/null 2>&1
+
+ # Go online
+ uqmi -s -d "$device" --set-device-operating-mode online > /dev/null 2>&1
# Set IP format
uqmi -s -d "$device" --set-data-format 802.3 > /dev/null 2>&1
uqmi -s -d "$device" --sync > /dev/null 2>&1
+ uqmi -s -d "$device" --network-register > /dev/null 2>&1
+
echo "Waiting for network registration"
+ sleep 1
local registration_timeout=0
- while uqmi -s -d "$device" --get-serving-system | grep '"searching"' > /dev/null; do
- [ -e "$device" ] || return 1
- if [ "$registration_timeout" -lt "$timeout" ]; then
- let registration_timeout++
- sleep 1;
+ local registration_state=""
+ while true; do
+ registration_state=$(uqmi -s -d "$device" --get-serving-system 2>/dev/null | jsonfilter -e "@.registration" 2>/dev/null)
+
+ [ "$registration_state" = "registered" ] && break
+
+ if [ "$registration_state" = "searching" ] || [ "$registration_state" = "not_registered" ]; then
+ if [ "$registration_timeout" -lt "$timeout" ] || [ "$timeout" = "0" ]; then
+ [ "$registration_state" = "searching" ] || {
+ echo "Device stopped network registration. Restart network registration"
+ uqmi -s -d "$device" --network-register > /dev/null 2>&1
+ }
+ let registration_timeout++
+ sleep 1
+ continue
+ fi
+ echo "Network registration failed, registration timeout reached"
else
- echo "Network registration failed"
- proto_notify_error "$interface" NETWORK_REGISTRATION_FAILED
- proto_block_restart "$interface"
- return 1
+ # registration_state is 'registration_denied' or 'unknown' or ''
+ echo "Network registration failed (reason: '$registration_state')"
fi
+
+ proto_notify_error "$interface" NETWORK_REGISTRATION_FAILED
+ return 1
done
[ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
- pdptype=$(echo "$pdptype" | awk '{print tolower($0)}')
+ pdptype="$(echo "$pdptype" | awk '{print tolower($0)}')"
+
[ "$pdptype" = "ip" -o "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] || pdptype="ip"
if [ "$pdptype" = "ip" ]; then
fi
# Check data connection state
- connstat=$(uqmi -s -d "$device" --get-data-status)
+ connstat=$(uqmi -s -d "$device" --set-client-id wds,"$cid_4" --get-data-status)
[ "$connstat" == '"connected"' ] || {
echo "No data link!"
uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds > /dev/null 2>&1
uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 > /dev/null 2>&1
+ : "${v6apn:=${apn}}"
+ : "${v6profile:=${profile}}"
+
pdh_6=$(uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
--start-network \
- ${apn:+--apn $apn} \
- ${profile:+--profile $profile} \
+ ${v6apn:+--apn $v6apn} \
+ ${v6profile:+--profile $v6profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
fi
# Check data connection state
- connstat=$(uqmi -s -d "$device" --get-data-status)
+ connstat=$(uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 --get-data-status)
[ "$connstat" == '"connected"' ] || {
echo "No data link!"
uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds > /dev/null 2>&1
json_init
json_add_string name "${interface}_6"
json_add_string ifname "@$interface"
+ [ "$pdptype" = "ipv4v6" ] && json_add_string iface_464xlat "0"
json_add_string proto "dhcpv6"
[ -n "$ip6table" ] && json_add_string ip6table "$ip6table"
proto_add_dynamic_defaults
}
[ -n "$pdh_4" ] && {
- json_init
- json_add_string name "${interface}_4"
- json_add_string ifname "@$interface"
- json_add_string proto "dhcp"
- [ -n "$ip4table" ] && json_add_string ip4table "$ip4table"
- proto_add_dynamic_defaults
- [ -n "$zone" ] && json_add_string zone "$zone"
- json_close_object
- ubus call network add_dynamic "$(json_dump)"
+ if [ "$dhcp" = 0 ]; then
+ json_load "$(uqmi -s -d $device --set-client-id wds,$cid_4 --get-current-settings)"
+ json_select ipv4
+ json_get_var ip_4 ip
+ json_get_var gateway_4 gateway
+ json_get_var dns1_4 dns1
+ json_get_var dns2_4 dns2
+ json_get_var subnet_4 subnet
+
+ proto_init_update "$ifname" 1
+ proto_set_keep 1
+ proto_add_ipv4_address "$ip_4" "$subnet_4"
+ proto_add_ipv4_route "$gateway_4" "128"
+ [ "$defaultroute" = 0 ] || proto_add_ipv4_route "0.0.0.0" 0 "$gateway_4"
+ [ "$peerdns" = 0 ] || {
+ proto_add_dns_server "$dns1_4"
+ proto_add_dns_server "$dns2_4"
+ }
+ [ -n "$zone" ] && {
+ proto_add_data
+ json_add_string zone "$zone"
+ proto_close_data
+ }
+ proto_send_update "$interface"
+ else
+ json_init
+ json_add_string name "${interface}_4"
+ json_add_string ifname "@$interface"
+ json_add_string proto "dhcp"
+ [ -n "$ip4table" ] && json_add_string ip4table "$ip4table"
+ proto_add_dynamic_defaults
+ [ -n "$zone" ] && json_add_string zone "$zone"
+ json_close_object
+ ubus call network add_dynamic "$(json_dump)"
+ fi
}
}
projects / openwrt / staging / wigyori.git / blobdiff