// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/dts-v1/;
+
+#include "ar9341.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include "ar9341.dtsi"
-
/ {
model = "PowerCloud Systems CR3000";
compatible = "pcs,cr3000", "qca,ar9341";
aliases {
- serial0 = &uart;
- led-status = &status;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
};
keys {
- compatible = "gpio-keys-polled";
- poll-interval = <20>;
- #address-cells = <1>;
- #size-cells = <0>;
+ compatible = "gpio-keys";
+
pinctrl-names = "default";
pinctrl-0 = <&jtag_disable_pins>;
leds {
compatible = "gpio-leds";
- status: power {
- label = "pcs:amber:power";
+ led_power: power {
+ label = "amber:power";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wlan2g {
- label = "pcs:blue:wlan";
+ label = "blue:wlan";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
- default-state = "off";
linux,default-trigger = "phy0tpt";
};
wan {
- label = "pcs:blue:wan";
+ label = "blue:wan";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
- default-state = "off";
};
lan1 {
- label = "pcs:blue:lan1";
+ label = "blue:lan1";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
- default-state = "off";
};
lan2 {
- label = "pcs:blue:lan2";
+ label = "blue:lan2";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
- default-state = "off";
};
lan3 {
- label = "pcs:blue:lan3";
+ label = "blue:lan3";
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
- default-state = "off";
};
lan4 {
- label = "pcs:blue:lan4";
+ label = "blue:lan4";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
- default-state = "off";
};
};
};
clock-frequency = <25000000>;
};
-&uart {
- status = "okay";
-};
-
-&gpio {
- status = "okay";
-};
-
&spi {
- num-cs = <1>;
-
status = "okay";
flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
};
partition@50000 {
+ compatible = "denx,uimage";
label = "firmware";
reg = <0x050000 0x07a0000>;
};
status = "okay";
mtd-cal-data = <&art 0x1000>;
- mtd-mac-address = <&art 0x1002>;
};
ð0 {
phy-handle = <&swphy0>;
mtd-mac-address = <&art 0x0>;
- mtd-mac-address-increment = <1>;
-
+ mac-address-increment = <1>;
};
ð1 {
- status = "okay";
-
phy-handle = <&swphy4>;
- mtd-mac-address = <&art 0x0>;
- phy-mode = "gmii";
pll-data = <0x06000000 0x00000101 0x00001616>;
+ mtd-mac-address = <&art 0x0>;
+
gmac-config {
device = <&gmac>;
switch-phy-swap = <1>;