// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-#include "ar9344.dtsi"
+#include "ar9344_tplink_tl-wdrxxxx.dtsi"
/ {
aliases {
- led-boot = &system;
- led-failsafe = &system;
- led-running = &system;
- led-upgrade = &system;
+ label-mac-device = &ath9k;
};
- leds {
- compatible = "gpio-leds";
-
- usb1 {
- label = "tp-link:green:usb1";
- gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
- trigger-sources = <&hub_port1>;
- linux,default-trigger = "usbport";
- };
-
- usb2 {
- label = "tp-link:green:usb2";
- gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
- trigger-sources = <&hub_port2>;
- linux,default-trigger = "usbport";
- };
+ gpio-export {
+ compatible = "gpio-export";
- wlan2g {
- label = "tp-link:green:wlan2g";
- gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "phy0tpt";
+ gpio_usb1_power {
+ gpio-export,name = "tp-link:power:usb1";
+ gpio-export,output = <1>;
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
};
- system: system {
- label = "tp-link:green:system";
- gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
- default-state = "on";
+ gpio_usb2_power {
+ gpio-export,name = "tp-link:power:usb2";
+ gpio-export,output = <1>;
+ gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
};
- qss {
- label = "tp-link:green:qss";
- gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ gpio_ext_lna0 {
+ gpio-export,name = "tp-link:ext:lna0";
+ gpio-export,output = <1>;
+ gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
};
- };
-
- ath9k-leds {
- compatible = "gpio-leds";
- wlan5g {
- label = "tp-link:green:wlan5g";
- gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "phy1tpt";
+ gpio_ext_lna1 {
+ gpio-export,name = "tp-link:ext:lna1";
+ gpio-export,output = <1>;
+ gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
};
};
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- linux,code = <KEY_RESTART>;
- gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- };
-
- wifi {
- linux,code = <KEY_RFKILL>;
- linux,input-type = <EV_SW>;
- gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- };
- };
-};
-
-&ref {
- clock-frequency = <40000000>;
};
-&uart {
- status = "okay";
-};
-
-&gpio {
- status = "okay";
-
- lna0 {
- gpio-hog;
- gpios = <18 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "tp-link:ext:lna0";
- };
-
- lna1 {
- gpio-hog;
- gpios = <19 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "tp-link:ext:lna1";
- };
-
- usb1_power {
- gpio-hog;
- gpios = <22 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "tp-link:power:usb1";
+&leds {
+ usb1 {
+ label = "green:usb1";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&hub_port1>;
+ linux,default-trigger = "usbport";
};
- usb2_power {
- gpio-hog;
- gpios = <21 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "tp-link:power:usb2";
- };
-};
-
-&spi {
- num-cs = <1>;
-
- status = "okay";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <25000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- uboot: partition@0 {
- label = "u-boot";
- reg = <0x000000 0x020000>;
- read-only;
- };
-
- partition@20000 {
- compatible = "tplink,firmware";
- label = "firmware";
- reg = <0x020000 0x7d0000>;
- };
-
- art: partition@7f0000 {
- label = "art";
- reg = <0x7f0000 0x010000>;
- read-only;
- };
- };
+ usb2 {
+ label = "green:usb2";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&hub_port2>;
+ linux,default-trigger = "usbport";
};
};
status = "okay";
};
-&pcie {
- status = "okay";
-
- ath9k: wifi@0,0 {
- compatible = "pci168c,0033";
- reg = <0x0000 0 0 0 0>;
- mtd-mac-address = <&uboot 0x1fc00>;
- qca,no-eeprom;
- #gpio-cells = <2>;
- gpio-controller;
- };
+&ath9k {
+ mtd-mac-address = <&uboot 0x1fc00>;
};
&wmac {
- status = "okay";
-
- mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&uboot 0x1fc00>;
- mtd-mac-address-increment = <(-1)>;
+ mac-address-increment = <(-1)>;
};
&mdio0 {
qca,ar8327-initvals = <
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
- 0x10 0x80000080 /* POWER_ON_STRIP */
+ 0x10 0x80000080 /* POWER_ON_STRAP */
0x50 0xc737c737 /* LED_CTRL0 */
0x54 0x00000000 /* LED_CTRL1 */
0x58 0x00000000 /* LED_CTRL2 */
pll-data = <0x06000000 0x00000101 0x00001616>;
mtd-mac-address = <&uboot 0x1fc00>;
- mtd-mac-address-increment = <(-2)>;
phy-mode = "rgmii";
phy-handle = <&phy0>;