-#include "qcom-ipq8064-v1.0.dtsi"
+#include "qcom-ipq8064-v2.0.dtsi"
#include <dt-bindings/input/input.h>
device_type = "memory";
};
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
aliases {
- serial0 = &uart4;
mdio-gpio0 = &mdio0;
led-boot = &power_white;
chosen {
bootargs = "rootfstype=squashfs noinitrd";
- linux,stdout-path = "serial0:115200n8";
};
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
+ };
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
+ usb1 {
+ label = "white:usb1";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
};
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
+ usb2 {
+ label = "white:usb2";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
};
- sata-phy@1b400000 {
- status = "ok";
+ power_amber: power_amber {
+ label = "amber:power";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
};
- sata@29000000 {
- status = "ok";
+ wan_white {
+ label = "white:wan";
+ gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
};
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
+ wan_amber {
+ label = "amber:wan";
+ gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
};
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
+ wps {
+ label = "white:wps";
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
};
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
+ esata {
+ label = "white:esata";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
};
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
+ power_white: power_white {
+ label = "white:power";
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
};
- usb30@0 {
- status = "ok";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
+ wifi {
+ label = "white:wifi";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
};
+ };
+};
- usb30@1 {
- status = "ok";
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
};
+ };
- pcie0: pci@1b500000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
+ usb0_pwr_en_pins: usb0_pwr_en_pins {
+ mux {
+ pins = "gpio15";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
};
+ };
- pcie1: pci@1b700000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
+ usb1_pwr_en_pins: usb1_pwr_en_pins {
+ mux {
+ pins = "gpio16", "gpio68";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
};
+ };
+};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb0_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie1 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ max-link-speed = <1>;
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
- nand@1ac00000 {
- status = "ok";
+ #address-cells = <1>;
+ #size-cells = <0>;
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+ nand-is-boot-medium;
+ qcom,boot_pages_size = <0x1180000>;
+
+ partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
kernel@1480000 {
label = "kernel";
- reg = <0x1480000 0x0200000>;
+ reg = <0x1480000 0x0400000>;
};
- ubi@1680000 {
+ ubi@1880000 {
label = "ubi";
- reg = <0x1680000 0x1E00000>;
+ reg = <0x1880000 0x1C00000>;
};
netgear@3480000 {
reg = <0x7900000 0x0700000>;
read-only;
};
-
- firmware@1480000 {
- label = "firmware";
- reg = <0x1480000 0x2000000>;
- };
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- phy-handle = <&phy4>;
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
};
};
+};
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
+&mdio0 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
};
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "d7800:white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+};
- usb2 {
- label = "d7800:white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
- power_amber: power_amber {
- label = "d7800:amber:power";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
- wan_white {
- label = "d7800:white:wan";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
+ mtd-mac-address = <&art 6>;
- wan_amber {
- label = "d7800:amber:wan";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
- wps {
- label = "d7800:white:wps";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
- esata {
- label = "d7800:white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
+ mtd-mac-address = <&art 0>;
- power_white: power_white {
- label = "d7800:white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "d7800:white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
};
};
&adm_dma {
- status = "ok";
+ status = "okay";
};
projects / openwrt / staging / zorun.git / blobdiff