};
soc {
- pinmux@800000 {
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
- "gpio26", "gpio53", "gpio56", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- W25Q128@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- MIBIB@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- SBL2@40000 {
- label = "SBL2";
- reg = <0x40000 0x40000>;
- read-only;
- };
-
- SBL3@80000 {
- label = "SBL3";
- reg = <0x80000 0x80000>;
- read-only;
- };
-
- DDRCONFIG@100000 {
- label = "DDRCONFIG";
- reg = <0x100000 0x10000>;
- read-only;
- };
-
- SSD@110000 {
- label = "SSD";
- reg = <0x110000 0x10000>;
- read-only;
- };
-
- TZ@120000 {
- label = "TZ";
- reg = <0x120000 0x80000>;
- read-only;
- };
-
- RPM@1a0000 {
- label = "RPM";
- reg = <0x1a0000 0x80000>;
- read-only;
- };
-
- APPSBL@220000 {
- label = "APPSBL";
- reg = <0x220000 0x80000>;
- read-only;
- };
-
- APPSBLENV@2a0000 {
- label = "APPSBLENV";
- reg = <0x2a0000 0x40000>;
- read-only;
- };
-
- OLDART@2e0000 {
- label = "OLDART";
- reg = <0x2e0000 0x40000>;
- read-only;
- };
-
- kernel@320000 {
- label = "kernel";
- reg = <0x320000 0x300000>;
- };
-
- rootfs@620000 {
- label = "rootfs";
- reg = <0x620000 0x960000>;
- };
-
- defaultmac: default-mac@0xfaf100 {
- label = "default-mac";
- reg = <0xfaf100 0x00200>;
- read-only;
- };
-
- ART@fc0000 {
- label = "ART";
- reg = <0xfc0000 0x40000>;
- read-only;
- };
- };
- };
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&defaultmac 0>;
- mtd-mac-address-increment = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&defaultmac 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
+ "gpio26", "gpio53", "gpio56", "gpio66";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ button_pins: button_pins {
+ mux {
+ pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi4: spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ W25Q128@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ MIBIB@20000 {
+ label = "MIBIB";
+ reg = <0x20000 0x20000>;
+ read-only;
+ };
+
+ SBL2@40000 {
+ label = "SBL2";
+ reg = <0x40000 0x40000>;
+ read-only;
+ };
+
+ SBL3@80000 {
+ label = "SBL3";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ DDRCONFIG@100000 {
+ label = "DDRCONFIG";
+ reg = <0x100000 0x10000>;
+ read-only;
+ };
+
+ SSD@110000 {
+ label = "SSD";
+ reg = <0x110000 0x10000>;
+ read-only;
+ };
+
+ TZ@120000 {
+ label = "TZ";
+ reg = <0x120000 0x80000>;
+ read-only;
+ };
+
+ RPM@1a0000 {
+ label = "RPM";
+ reg = <0x1a0000 0x80000>;
+ read-only;
+ };
+
+ APPSBL@220000 {
+ label = "APPSBL";
+ reg = <0x220000 0x80000>;
+ read-only;
+ };
+
+ APPSBLENV@2a0000 {
+ label = "APPSBLENV";
+ reg = <0x2a0000 0x40000>;
+ read-only;
+ };
+
+ OLDART@2e0000 {
+ label = "OLDART";
+ reg = <0x2e0000 0x40000>;
+ read-only;
+ };
+
+ kernel@320000 {
+ label = "kernel";
+ reg = <0x320000 0x300000>;
+ };
+
+ rootfs@620000 {
+ label = "rootfs";
+ reg = <0x620000 0x960000>;
+ };
+
+ defaultmac: default-mac@0xfaf100 {
+ label = "default-mac";
+ reg = <0xfaf100 0x00200>;
+ read-only;
+ };
+
+ ART@fc0000 {
+ label = "ART";
+ reg = <0xfc0000 0x40000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&defaultmac 0>;
+ mtd-mac-address-increment = <1>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&defaultmac 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&adm_dma {
status = "okay";
};
projects / openwrt / staging / hauke.git / blobdiff