#include "vr9.dtsi"
+#include <dt-bindings/input/input.h>
+
/ {
model = "FRITZ7360SL - 1&1 HomeServer";
chosen {
- bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+ bootargs = "console=ttyLTQ0,115200";
};
aliases {
led-running = &power_green;
led-internet = &info_green;
- led-dsl = &power_green;
led-wifi = &wifi;
};
};
phy-rst {
lantiq,pins = "io37", "io44";
- lantiq,pull = <2>;
+ lantiq,pull = <0>;
lantiq,open-drain;
lantiq,output = <1>;
};
};
};
- ath9k_eep {
- compatible = "ath9k,eeprom";
- ath,eep-flash = <&urlader 0x985>;
- ath,eep-endian;
- ath,eep-swap;
- ath,pci-slot = <0>;
- };
-
gphy-xrx200 {
compatible = "lantiq,phy-xrx200";
firmware = "lantiq/vr9_phy11g_a2x.bin";
#size-cells = <0>;
poll-interval = <100>;
dect {
- label = "power";
+ label = "dect";
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
- linux,code = <BTN_2>;
+ linux,code = <KEY_PHONE>;
};
wifi {
label = "wifi";
gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
- linux,code = <BTN_1>;
+ linux,code = <KEY_WLAN>;
};
};
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
- mac-address = [ 00 11 22 33 44 55 ];
+ mtd-mac-address = <&urlader 0xa91>;
+ mtd-mac-address-increment = <(-2)>;
lantiq,switch;
ethernet@0 {
reg = <0>;
phy-mode = "rmii";
phy-handle = <&phy0>;
- // gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
};
ethernet@1 {
compatible = "lantiq,xrx200-pdi-port";
reg = <1>;
phy-mode = "rmii";
phy-handle = <&phy1>;
- // gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";
compatible = "lantiq,xrx200-mdio";
phy0: ethernet-phy@0 {
reg = <0x00>;
- compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+ compatible = "ethernet-phy-id004d.d076", "ethernet-phy-ieee802.3-c22";
+ reset-gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
};
phy1: ethernet-phy@1 {
reg = <0x01>;
- compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+ compatible = "ethernet-phy-id004d.d076", "ethernet-phy-ieee802.3-c22";
+ reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
phy11: ethernet-phy@11 {
reg = <0x11>;
};
};
};
+
+&pcie0 {
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+
+ wifi@168c,002e {
+ compatible = "pci168c,002e";
+ reg = <0 0 0 0 0>;
+ qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */
+ };
+ };
+};