#include <linux/module.h>
#include <linux/delay.h>
+#include <linux/of.h>
#include <linux/phy.h>
#include <linux/netdevice.h>
#include <linux/firmware.h>
#include <linux/crc32.h>
+#include <linux/sfp.h>
#include <asm/mach-rtl838x/mach-rtl83xx.h>
#include "rtl83xx-phy.h"
-
extern struct rtl83xx_soc_info soc_info;
extern struct mutex smi_lock;
+#define PHY_CTRL_REG 0
+#define PHY_POWER_BIT 11
+
+#define PHY_PAGE_2 2
+#define PHY_PAGE_4 4
+
+/* all Clause-22 RealTek MDIO PHYs use register 0x1f for page select */
+#define RTL8XXX_PAGE_SELECT 0x1f
+
+#define RTL8XXX_PAGE_MAIN 0x0000
+#define RTL821X_PAGE_PORT 0x0266
+#define RTL821X_PAGE_POWER 0x0a40
+#define RTL821X_PAGE_GPHY 0x0a42
+#define RTL821X_PAGE_MAC 0x0a43
+#define RTL821X_PAGE_STATE 0x0b80
+#define RTL821X_PAGE_PATCH 0x0b82
+
+/*
+ * Using the special page 0xfff with the MDIO controller found in
+ * RealTek SoCs allows to access the PHY in RAW mode, ie. bypassing
+ * the cache and paging engine of the MDIO controller.
+ */
+#define RTL83XX_PAGE_RAW 0x0fff
+
+/* internal RTL821X PHY uses register 0x1d to select media page */
+#define RTL821XINT_MEDIA_PAGE_SELECT 0x1d
+/* external RTL821X PHY uses register 0x1e to select media page */
+#define RTL821XEXT_MEDIA_PAGE_SELECT 0x1e
+
+#define RTL821X_MEDIA_PAGE_AUTO 0
+#define RTL821X_MEDIA_PAGE_COPPER 1
+#define RTL821X_MEDIA_PAGE_FIBRE 3
+#define RTL821X_MEDIA_PAGE_INTERNAL 8
+
+#define RTL9300_PHY_ID_MASK 0xf0ffffff
+
/*
* This lock protects the state of the SoC automatically polling the PHYs over the SMI
* bus to detect e.g. link and media changes. For operations on the PHYs such as
static const struct firmware rtl838x_8214fc_fw;
static const struct firmware rtl838x_8218b_fw;
-int rtl838x_read_mmd_phy(u32 port, u32 devnum, u32 regnum, u32 *val);
-int rtl838x_write_mmd_phy(u32 port, u32 devnum, u32 reg, u32 val);
-int rtl839x_read_mmd_phy(u32 port, u32 devnum, u32 regnum, u32 *val);
-int rtl839x_write_mmd_phy(u32 port, u32 devnum, u32 reg, u32 val);
-int rtl930x_read_mmd_phy(u32 port, u32 devnum, u32 regnum, u32 *val);
-int rtl930x_write_mmd_phy(u32 port, u32 devnum, u32 reg, u32 val);
-int rtl931x_read_mmd_phy(u32 port, u32 devnum, u32 regnum, u32 *val);
-int rtl931x_write_mmd_phy(u32 port, u32 devnum, u32 reg, u32 val);
-
-static int read_phy(u32 port, u32 page, u32 reg, u32 *val)
-{ switch (soc_info.family) {
- case RTL8380_FAMILY_ID:
- return rtl838x_read_phy(port, page, reg, val);
- case RTL8390_FAMILY_ID:
- return rtl839x_read_phy(port, page, reg, val);
- case RTL9300_FAMILY_ID:
- return rtl930x_read_phy(port, page, reg, val);
- case RTL9310_FAMILY_ID:
- return rtl931x_read_phy(port, page, reg, val);
- }
- return -1;
-}
-
-static int write_phy(u32 port, u32 page, u32 reg, u32 val)
-{
- switch (soc_info.family) {
- case RTL8380_FAMILY_ID:
- return rtl838x_write_phy(port, page, reg, val);
- case RTL8390_FAMILY_ID:
- return rtl839x_write_phy(port, page, reg, val);
- case RTL9300_FAMILY_ID:
- return rtl930x_write_phy(port, page, reg, val);
- case RTL9310_FAMILY_ID:
- return rtl931x_write_phy(port, page, reg, val);
- }
- return -1;
-}
-
-static int read_mmd_phy(u32 port, u32 devnum, u32 regnum, u32 *val)
-{
- switch (soc_info.family) {
- case RTL8380_FAMILY_ID:
- return rtl838x_read_mmd_phy(port, devnum, regnum, val);
- case RTL8390_FAMILY_ID:
- return rtl839x_read_mmd_phy(port, devnum, regnum, val);
- case RTL9300_FAMILY_ID:
- return rtl930x_read_mmd_phy(port, devnum, regnum, val);
- case RTL9310_FAMILY_ID:
- return rtl931x_read_mmd_phy(port, devnum, regnum, val);
- }
- return -1;
-}
-
-int write_mmd_phy(u32 port, u32 devnum, u32 reg, u32 val)
-{
- switch (soc_info.family) {
- case RTL8380_FAMILY_ID:
- return rtl838x_write_mmd_phy(port, devnum, reg, val);
- case RTL8390_FAMILY_ID:
- return rtl839x_write_mmd_phy(port, devnum, reg, val);
- case RTL9300_FAMILY_ID:
- return rtl930x_write_mmd_phy(port, devnum, reg, val);
- case RTL9310_FAMILY_ID:
- return rtl931x_write_mmd_phy(port, devnum, reg, val);
- }
- return -1;
-}
-
static u64 disable_polling(int port)
{
u64 saved_state;
return 0;
}
-static void rtl8380_int_phy_on_off(int mac, bool on)
+static void rtl8380_int_phy_on_off(struct phy_device *phydev, bool on)
{
- u32 val;
-
- read_phy(mac, 0, 0, &val);
- if (on)
- write_phy(mac, 0, 0, val & ~BIT(11));
- else
- write_phy(mac, 0, 0, val | BIT(11));
+ phy_modify(phydev, 0, BIT(11), on?0:BIT(11));
}
-static void rtl8380_rtl8214fc_on_off(int mac, bool on)
+static void rtl8380_rtl8214fc_on_off(struct phy_device *phydev, bool on)
{
- u32 val;
-
/* fiber ports */
- write_phy(mac, 4095, 30, 3);
- read_phy(mac, 0, 16, &val);
- if (on)
- write_phy(mac, 0, 16, val & ~BIT(11));
- else
- write_phy(mac, 0, 16, val | BIT(11));
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_FIBRE);
+ phy_modify(phydev, 0x10, BIT(11), on?0:BIT(11));
/* copper ports */
- write_phy(mac, 4095, 30, 1);
- read_phy(mac, 0, 16, &val);
- if (on)
- write_phy(mac, 0xa40, 16, val & ~BIT(11));
- else
- write_phy(mac, 0xa40, 16, val | BIT(11));
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
+ phy_modify_paged(phydev, RTL821X_PAGE_POWER, 0x10, BIT(11), on?0:BIT(11));
}
-static void rtl8380_phy_reset(int mac)
+static void rtl8380_phy_reset(struct phy_device *phydev)
{
- u32 val;
-
- read_phy(mac, 0, 0, &val);
- write_phy(mac, 0, 0, val | BIT(15));
+ phy_modify(phydev, 0, BIT(15), BIT(15));
}
+// The access registers for SDS_MODE_SEL and the LSB for each SDS within
+u16 rtl9300_sds_regs[] = { 0x0194, 0x0194, 0x0194, 0x0194, 0x02a0, 0x02a0, 0x02a0, 0x02a0,
+ 0x02A4, 0x02A4, 0x0198, 0x0198 };
+u8 rtl9300_sds_lsb[] = { 0, 6, 12, 18, 0, 6, 12, 18, 0, 6, 0, 6};
+
/*
* Reset the SerDes by powering it off and set a new operations mode
* of the SerDes. 0x1f is off. Other modes are
- * 0x01: QSGMII 0x04: 1000BX_FIBER 0x05: FIBER100
+ * 0x02: SGMII 0x04: 1000BX_FIBER 0x05: FIBER100
* 0x06: QSGMII 0x09: RSGMII 0x0d: USXGMII
* 0x10: XSGMII 0x12: HISGMII 0x16: 2500Base_X
* 0x17: RXAUI_LITE 0x19: RXAUI_PLUS 0x1a: 10G Base-R
*/
void rtl9300_sds_rst(int sds_num, u32 mode)
{
- // The access registers for SDS_MODE_SEL and the LSB for each SDS within
- u16 regs[] = { 0x0194, 0x0194, 0x0194, 0x0194, 0x02a0, 0x02a0, 0x02a0, 0x02a0,
- 0x02A4, 0x02A4, 0x0198, 0x0198 };
- u8 lsb[] = { 0, 6, 12, 18, 0, 6, 12, 18, 0, 6, 0, 6};
-
pr_info("%s %d\n", __func__, mode);
if (sds_num < 0 || sds_num > 11) {
pr_err("Wrong SerDes number: %d\n", sds_num);
return;
}
- sw_w32_mask(0x1f << lsb[sds_num], 0x1f << lsb[sds_num], regs[sds_num]);
+ sw_w32_mask(0x1f << rtl9300_sds_lsb[sds_num], 0x1f << rtl9300_sds_lsb[sds_num],
+ rtl9300_sds_regs[sds_num]);
mdelay(10);
- sw_w32_mask(0x1f << lsb[sds_num], mode << lsb[sds_num], regs[sds_num]);
+ sw_w32_mask(0x1f << rtl9300_sds_lsb[sds_num], mode << rtl9300_sds_lsb[sds_num],
+ rtl9300_sds_regs[sds_num]);
+ mdelay(10);
+
+ pr_debug("%s: 194:%08x 198:%08x 2a0:%08x 2a4:%08x\n", __func__,
+ sw_r32(0x194), sw_r32(0x198), sw_r32(0x2a0), sw_r32(0x2a4));
+}
+
+void rtl9300_sds_set(int sds_num, u32 mode)
+{
+ pr_info("%s %d\n", __func__, mode);
+ if (sds_num < 0 || sds_num > 11) {
+ pr_err("Wrong SerDes number: %d\n", sds_num);
+ return;
+ }
+
+ sw_w32_mask(0x1f << rtl9300_sds_lsb[sds_num], mode << rtl9300_sds_lsb[sds_num],
+ rtl9300_sds_regs[sds_num]);
mdelay(10);
pr_debug("%s: 194:%08x 198:%08x 2a0:%08x 2a4:%08x\n", __func__,
sw_r32(0x194), sw_r32(0x198), sw_r32(0x2a0), sw_r32(0x2a4));
}
+u32 rtl9300_sds_mode_get(int sds_num)
+{
+ u32 v;
+
+ if (sds_num < 0 || sds_num > 11) {
+ pr_err("Wrong SerDes number: %d\n", sds_num);
+ return 0;
+ }
+
+ v = sw_r32(rtl9300_sds_regs[sds_num]);
+ v >>= rtl9300_sds_lsb[sds_num];
+
+ return v & 0x1f;
+}
+
/*
* On the RTL839x family of SoCs with inbuilt SerDes, these SerDes are accessed through
* a 2048 bit register that holds the contents of the PHY being simulated by the SoC.
int i;
u32 cmd = phy_addr << 2 | page << 7 | phy_reg << 13 | 1;
- pr_debug("%s: phy_addr %d, phy_reg: %d\n", __func__, phy_addr, phy_reg);
sw_w32(cmd, RTL930X_SDS_INDACS_CMD);
for (i = 0; i < 100; i++) {
if (i >= 100)
return -EIO;
- pr_debug("%s: returning %04x\n", __func__, sw_r32(RTL930X_SDS_INDACS_DATA) & 0xffff);
return sw_r32(RTL930X_SDS_INDACS_DATA) & 0xffff;
}
mdelay(1);
}
- if (i >= 100)
+
+ if (i >= 100) {
+ pr_info("%s ERROR !!!!!!!!!!!!!!!!!!!!\n", __func__);
return -EIO;
+ }
return 0;
}
static int rtl8226_read_page(struct phy_device *phydev)
{
- return __phy_read(phydev, 0x1f);
+ return __phy_read(phydev, RTL8XXX_PAGE_SELECT);
}
static int rtl8226_write_page(struct phy_device *phydev, int page)
{
- return __phy_write(phydev, 0x1f, page);
+ return __phy_write(phydev, RTL8XXX_PAGE_SELECT, page);
}
static int rtl8226_read_status(struct phy_device *phydev)
{
int ret = 0, i;
u32 val;
- int port = phydev->mdio.addr;
// TODO: ret = genphy_read_status(phydev);
// if (ret < 0) {
// Link status must be read twice
for (i = 0; i < 2; i++) {
- read_mmd_phy(port, MMD_VEND2, 0xA402, &val);
+ val = phy_read_mmd(phydev, MMD_VEND2, 0xA402);
}
phydev->link = val & BIT(2) ? 1 : 0;
if (!phydev->link)
goto out;
// Read duplex status
- ret = read_mmd_phy(port, MMD_VEND2, 0xA434, &val);
- if (ret)
+ val = phy_read_mmd(phydev, MMD_VEND2, 0xA434);
+ if (val < 0)
goto out;
phydev->duplex = !!(val & BIT(3));
// Read speed
- ret = read_mmd_phy(port, MMD_VEND2, 0xA434, &val);
+ val = phy_read_mmd(phydev, MMD_VEND2, 0xA434);
switch (val & 0x0630) {
case 0x0000:
phydev->speed = SPEED_10;
{
int ret = 0;
u32 v;
- int port = phydev->mdio.addr;
pr_info("In %s\n", __func__);
- ret = read_mmd_phy(port, MMD_AN, 16, &v);
- if (ret)
+ v = phy_read_mmd(phydev, MMD_AN, 16);
+ if (v < 0)
goto out;
v |= BIT(5); // HD 10M
v |= BIT(7); // HD 100M
v |= BIT(8); // FD 100M
- ret = write_mmd_phy(port, MMD_AN, 16, v);
+ ret = phy_write_mmd(phydev, MMD_AN, 16, v);
// Allow 1GBit
- ret = read_mmd_phy(port, MMD_VEND2, 0xA412, &v);
- if (ret)
+ v = phy_read_mmd(phydev, MMD_VEND2, 0xA412);
+ if (v < 0)
goto out;
v |= BIT(9); // FD 1000M
- ret = write_mmd_phy(port, MMD_VEND2, 0xA412, v);
- if (ret)
+ ret = phy_write_mmd(phydev, MMD_VEND2, 0xA412, v);
+ if (ret < 0)
goto out;
// Allow 2.5G
- ret = read_mmd_phy(port, MMD_AN, 32, &v);
- if (ret)
+ v = phy_read_mmd(phydev, MMD_AN, 32);
+ if (v < 0)
goto out;
v |= BIT(7);
- ret = write_mmd_phy(port, MMD_AN, 32, v);
+ ret = phy_write_mmd(phydev, MMD_AN, 32, v);
out:
return ret;
{
int ret = 0;
u32 v;
- int port = phydev->mdio.addr;
pr_debug("In %s\n", __func__);
if (phydev->autoneg == AUTONEG_ENABLE) {
if (ret)
goto out;
// AutoNegotiationEnable
- ret = read_mmd_phy(port, MMD_AN, 0, &v);
- if (ret)
+ v = phy_read_mmd(phydev, MMD_AN, 0);
+ if (v < 0)
goto out;
v |= BIT(12); // Enable AN
- ret = write_mmd_phy(port, MMD_AN, 0, v);
- if (ret)
+ ret = phy_write_mmd(phydev, MMD_AN, 0, v);
+ if (ret < 0)
goto out;
// RestartAutoNegotiation
- ret = read_mmd_phy(port, MMD_VEND2, 0xA400, &v);
- if (ret)
+ v = phy_read_mmd(phydev, MMD_VEND2, 0xA400);
+ if (v < 0)
goto out;
v |= BIT(9);
- ret = write_mmd_phy(port, MMD_VEND2, 0xA400, v);
+ ret = phy_write_mmd(phydev, MMD_VEND2, 0xA400, v);
}
// TODO: ret = __genphy_config_aneg(phydev, ret);
pr_debug("In %s, port %d, was enabled: %d\n", __func__, addr, e->eee_enabled);
- read_mmd_phy(addr, MMD_AN, 60, &val);
+ val = phy_read_mmd(phydev, MMD_AN, 60);
if (e->eee_enabled) {
e->eee_enabled = !!(val & BIT(1));
if (!e->eee_enabled) {
- read_mmd_phy(addr, MMD_AN, 62, &val);
+ val = phy_read_mmd(phydev, MMD_AN, 62);
e->eee_enabled = !!(val & BIT(0));
}
}
poll_state = disable_polling(port);
// Remember aneg state
- read_mmd_phy(port, MMD_AN, 0, &val);
+ val = phy_read_mmd(phydev, MMD_AN, 0);
an_enabled = !!(val & BIT(12));
// Setup 100/1000MBit
- read_mmd_phy(port, MMD_AN, 60, &val);
+ val = phy_read_mmd(phydev, MMD_AN, 60);
if (e->eee_enabled)
val |= 0x6;
else
val &= 0x6;
- write_mmd_phy(port, MMD_AN, 60, val);
+ phy_write_mmd(phydev, MMD_AN, 60, val);
// Setup 2.5GBit
- read_mmd_phy(port, MMD_AN, 62, &val);
+ val = phy_read_mmd(phydev, MMD_AN, 62);
if (e->eee_enabled)
val |= 0x1;
else
val &= 0x1;
- write_mmd_phy(port, MMD_AN, 62, val);
+ phy_write_mmd(phydev, MMD_AN, 62, val);
// RestartAutoNegotiation
- read_mmd_phy(port, MMD_VEND2, 0xA400, &val);
+ val = phy_read_mmd(phydev, MMD_VEND2, 0xA400);
val |= BIT(9);
- write_mmd_phy(port, MMD_VEND2, 0xA400, val);
+ phy_write_mmd(phydev, MMD_VEND2, 0xA400, val);
resume_polling(poll_state);
return NULL;
}
+static void rtl821x_phy_setup_package_broadcast(struct phy_device *phydev, bool enable)
+{
+ int mac = phydev->mdio.addr;
+
+ /* select main page 0 */
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL8XXX_PAGE_MAIN);
+ /* write to 0x8 to register 0x1d on main page 0 */
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_INTERNAL);
+ /* select page 0x266 */
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL821X_PAGE_PORT);
+ /* set phy id and target broadcast bitmap in register 0x16 on page 0x266 */
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, 0x16, (enable?0xff00:0x00) | mac);
+ /* return to main page 0 */
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL8XXX_PAGE_MAIN);
+ /* write to 0x0 to register 0x1d on main page 0 */
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
+ mdelay(1);
+}
+
static int rtl8390_configure_generic(struct phy_device *phydev)
{
- u32 val, phy_id;
int mac = phydev->mdio.addr;
+ u32 val, phy_id;
- read_phy(mac, 0, 2, &val);
+ val = phy_read(phydev, 2);
phy_id = val << 16;
- read_phy(mac, 0, 3, &val);
+ val = phy_read(phydev, 3);
phy_id |= val;
pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
/* Read internal PHY ID */
- write_phy(mac, 31, 27, 0x0002);
- read_phy(mac, 31, 28, &val);
+ phy_write_paged(phydev, 31, 27, 0x0002);
+ val = phy_read_paged(phydev, 31, 28);
/* Internal RTL8218B, version 2 */
phydev_info(phydev, "Detected unknown %x\n", val);
u32 *rtl838x_6275B_intPhy_perport;
u32 *rtl8218b_6276B_hwEsd_perport;
-
- read_phy(mac, 0, 2, &val);
+ val = phy_read(phydev, 2);
phy_id = val << 16;
- read_phy(mac, 0, 3, &val);
+ val = phy_read(phydev, 3);
phy_id |= val;
pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
/* Read internal PHY ID */
- write_phy(mac, 31, 27, 0x0002);
- read_phy(mac, 31, 28, &val);
+ phy_write_paged(phydev, 31, 27, 0x0002);
+ val = phy_read_paged(phydev, 31, 28);
if (val != 0x6275) {
phydev_err(phydev, "Expected internal RTL8218B, found PHY-ID %x\n", val);
return -1;
if (sw_r32(RTL838X_DMY_REG31) == 0x1)
ipd_flag = 1;
- read_phy(mac, 0, 0, &val);
- if (val & (1 << 11))
- rtl8380_int_phy_on_off(mac, true);
+ val = phy_read(phydev, 0);
+ if (val & BIT(11))
+ rtl8380_int_phy_on_off(phydev, true);
else
- rtl8380_phy_reset(mac);
+ rtl8380_phy_reset(phydev);
msleep(100);
/* Ready PHY for patch */
for (p = 0; p < 8; p++) {
- write_phy(mac + p, 0xfff, 0x1f, 0x0b82);
- write_phy(mac + p, 0xfff, 0x10, 0x0010);
+ phy_package_port_write_paged(phydev, p, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL821X_PAGE_PATCH);
+ phy_package_port_write_paged(phydev, p, RTL83XX_PAGE_RAW, 0x10, 0x0010);
}
msleep(500);
for (p = 0; p < 8; p++) {
for (i = 0; i < 100 ; i++) {
- read_phy(mac + p, 0x0b80, 0x10, &val);
+ val = phy_package_port_read_paged(phydev, p, RTL821X_PAGE_STATE, 0x10);
if (val & 0x40)
break;
}
for (p = 0; p < 8; p++) {
i = 0;
while (rtl838x_6275B_intPhy_perport[i * 2]) {
- write_phy(mac + p, 0xfff,
+ phy_package_port_write_paged(phydev, p, RTL83XX_PAGE_RAW,
rtl838x_6275B_intPhy_perport[i * 2],
rtl838x_6275B_intPhy_perport[i * 2 + 1]);
i++;
}
i = 0;
while (rtl8218b_6276B_hwEsd_perport[i * 2]) {
- write_phy(mac + p, 0xfff,
+ phy_package_port_write_paged(phydev, p, RTL83XX_PAGE_RAW,
rtl8218b_6276B_hwEsd_perport[i * 2],
rtl8218b_6276B_hwEsd_perport[i * 2 + 1]);
i++;
phydev_err(phydev, "External RTL8218B must have PHY-IDs 0 or 16!\n");
return -1;
}
- read_phy(mac, 0, 2, &val);
+ val = phy_read(phydev, 2);
phy_id = val << 16;
- read_phy(mac, 0, 3, &val);
+ val = phy_read(phydev, 3);
phy_id |= val;
pr_info("Phy on MAC %d: %x\n", mac, phy_id);
/* Read internal PHY ID */
- write_phy(mac, 31, 27, 0x0002);
- read_phy(mac, 31, 28, &val);
+ phy_write_paged(phydev, 31, 27, 0x0002);
+ val = phy_read_paged(phydev, 31, 28);
if (val != 0x6276) {
phydev_err(phydev, "Expected external RTL8218B, found PHY-ID %x\n", val);
return -1;
rtl8380_rtl8218b_perport = (void *)h + sizeof(struct fw_header)
+ h->parts[2].start;
- read_phy(mac, 0, 0, &val);
+ val = phy_read(phydev, 0);
if (val & (1 << 11))
- rtl8380_int_phy_on_off(mac, true);
+ rtl8380_int_phy_on_off(phydev, true);
else
- rtl8380_phy_reset(mac);
+ rtl8380_phy_reset(phydev);
+
msleep(100);
/* Get Chip revision */
- write_phy(mac, 0xfff, 0x1f, 0x0);
- write_phy(mac, 0xfff, 0x1b, 0x4);
- read_phy(mac, 0xfff, 0x1c, &val);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL8XXX_PAGE_MAIN);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, 0x1b, 0x4);
+ val = phy_read_paged(phydev, RTL83XX_PAGE_RAW, 0x1c);
+
+ phydev_info(phydev, "Detected chip revision %04x\n", val);
i = 0;
while (rtl8380_rtl8218b_perchip[i * 3]
&& rtl8380_rtl8218b_perchip[i * 3 + 1]) {
- write_phy(mac + rtl8380_rtl8218b_perchip[i * 3],
- 0xfff, rtl8380_rtl8218b_perchip[i * 3 + 1],
+ phy_package_port_write_paged(phydev, rtl8380_rtl8218b_perchip[i * 3],
+ RTL83XX_PAGE_RAW, rtl8380_rtl8218b_perchip[i * 3 + 1],
rtl8380_rtl8218b_perchip[i * 3 + 2]);
i++;
}
/* Enable PHY */
for (i = 0; i < 8; i++) {
- write_phy(mac + i, 0xfff, 0x1f, 0x0000);
- write_phy(mac + i, 0xfff, 0x00, 0x1140);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL8XXX_PAGE_MAIN);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, 0x00, 0x1140);
}
mdelay(100);
/* Request patch */
for (i = 0; i < 8; i++) {
- write_phy(mac + i, 0xfff, 0x1f, 0x0b82);
- write_phy(mac + i, 0xfff, 0x10, 0x0010);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL821X_PAGE_PATCH);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, 0x10, 0x0010);
}
+
mdelay(300);
/* Verify patch readiness */
for (i = 0; i < 8; i++) {
for (l = 0; l < 100; l++) {
- read_phy(mac + i, 0xb80, 0x10, &val);
+ val = phy_package_port_read_paged(phydev, i, RTL821X_PAGE_STATE, 0x10);
if (val & 0x40)
break;
}
}
/* Use Broadcast ID method for patching */
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0008);
- write_phy(mac, 0xfff, 0x1f, 0x0266);
- write_phy(mac, 0xfff, 0x16, 0xff00 + mac);
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0000);
- mdelay(1);
+ rtl821x_phy_setup_package_broadcast(phydev, true);
- write_phy(mac, 0xfff, 30, 8);
- write_phy(mac, 0x26e, 17, 0xb);
- write_phy(mac, 0x26e, 16, 0x2);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, 30, 8);
+ phy_write_paged(phydev, 0x26e, 17, 0xb);
+ phy_write_paged(phydev, 0x26e, 16, 0x2);
mdelay(1);
- read_phy(mac, 0x26e, 19, &ipd);
- write_phy(mac, 0, 30, 0);
- ipd = (ipd >> 4) & 0xf;
+ ipd = phy_read_paged(phydev, 0x26e, 19);
+ phy_write_paged(phydev, 0, 30, 0);
+ ipd = (ipd >> 4) & 0xf; /* unused ? */
i = 0;
while (rtl8218B_6276B_rtl8380_perport[i * 2]) {
- write_phy(mac, 0xfff, rtl8218B_6276B_rtl8380_perport[i * 2],
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, rtl8218B_6276B_rtl8380_perport[i * 2],
rtl8218B_6276B_rtl8380_perport[i * 2 + 1]);
i++;
}
/*Disable broadcast ID*/
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0008);
- write_phy(mac, 0xfff, 0x1f, 0x0266);
- write_phy(mac, 0xfff, 0x16, 0x00 + mac);
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0000);
- mdelay(1);
+ rtl821x_phy_setup_package_broadcast(phydev, false);
return 0;
}
return phydev->phy_id == PHY_ID_RTL8218B_E;
}
-static int rtl8218b_read_mmd(struct phy_device *phydev,
- int devnum, u16 regnum)
+static bool rtl8214fc_media_is_fibre(struct phy_device *phydev)
{
- int ret;
+ int mac = phydev->mdio.addr;
+
+ static int reg[] = {16, 19, 20, 21};
u32 val;
- int addr = phydev->mdio.addr;
- ret = read_mmd_phy(addr, devnum, regnum, &val);
- if (ret)
- return ret;
- return val;
+ phy_package_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_INTERNAL);
+ val = phy_package_read_paged(phydev, RTL821X_PAGE_PORT, reg[mac % 4]);
+ phy_package_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
+
+ if (val & BIT(11))
+ return false;
+
+ return true;
}
-static int rtl8218b_write_mmd(struct phy_device *phydev,
- int devnum, u16 regnum, u16 val)
+static void rtl8214fc_power_set(struct phy_device *phydev, int port, bool on)
{
- int addr = phydev->mdio.addr;
+ char *state = on ? "on" : "off";
+
+ if (port == PORT_FIBRE) {
+ pr_info("%s: Powering %s FIBRE (port %d)\n", __func__, state, phydev->mdio.addr);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_FIBRE);
+ } else {
+ pr_info("%s: Powering %s COPPER (port %d)\n", __func__, state, phydev->mdio.addr);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
+ }
+
+ if (on) {
+ phy_modify_paged(phydev, RTL821X_PAGE_POWER, 0x10, BIT(11), 0);
+ } else {
+ phy_modify_paged(phydev, RTL821X_PAGE_POWER, 0x10, 0, BIT(11));
+ }
- return rtl838x_write_mmd_phy(addr, devnum, regnum, val);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
}
-static int rtl8226_read_mmd(struct phy_device *phydev, int devnum, u16 regnum)
+static int rtl8214fc_suspend(struct phy_device *phydev)
{
- int port = phydev->mdio.addr; // the SoC translates port addresses to PHY addr
- int err;
- u32 val;
+ rtl8214fc_power_set(phydev, PORT_MII, false);
+ rtl8214fc_power_set(phydev, PORT_FIBRE, false);
- err = read_mmd_phy(port, devnum, regnum, &val);
- if (err)
- return err;
- return val;
+ return 0;
}
-static int rtl8226_write_mmd(struct phy_device *phydev, int devnum, u16 regnum, u16 val)
+static int rtl8214fc_resume(struct phy_device *phydev)
{
- int port = phydev->mdio.addr; // the SoC translates port addresses to PHY addr
+ if (rtl8214fc_media_is_fibre(phydev)) {
+ rtl8214fc_power_set(phydev, PORT_MII, false);
+ rtl8214fc_power_set(phydev, PORT_FIBRE, true);
+ } else {
+ rtl8214fc_power_set(phydev, PORT_FIBRE, false);
+ rtl8214fc_power_set(phydev, PORT_MII, true);
+ }
- return write_mmd_phy(port, devnum, regnum, val);
+ return 0;
}
-static void rtl8380_rtl8214fc_media_set(int mac, bool set_fibre)
+static void rtl8214fc_media_set(struct phy_device *phydev, bool set_fibre)
{
- int base = mac - (mac % 4);
+ int mac = phydev->mdio.addr;
+
static int reg[] = {16, 19, 20, 21};
- int val, media, power;
+ int val;
pr_info("%s: port %d, set_fibre: %d\n", __func__, mac, set_fibre);
- write_phy(base, 0xfff, 29, 8);
- read_phy(base, 0x266, reg[mac % 4], &val);
-
- media = (val >> 10) & 0x3;
- pr_info("Current media %x\n", media);
- if (media & 0x2) {
- pr_info("Powering off COPPER\n");
- write_phy(base, 0xfff, 29, 1);
- /* Ensure power is off */
- read_phy(base, 0xa40, 16, &power);
- if (!(power & (1 << 11)))
- write_phy(base, 0xa40, 16, power | (1 << 11));
- } else {
- pr_info("Powering off FIBRE");
- write_phy(base, 0xfff, 29, 3);
- /* Ensure power is off */
- read_phy(base, 0xa40, 16, &power);
- if (!(power & (1 << 11)))
- write_phy(base, 0xa40, 16, power | (1 << 11));
- }
-
- if (set_fibre) {
- val |= 1 << 10;
- val &= ~(1 << 11);
- } else {
- val |= 1 << 10;
- val |= 1 << 11;
- }
- write_phy(base, 0xfff, 29, 8);
- write_phy(base, 0x266, reg[mac % 4], val);
- write_phy(base, 0xfff, 29, 0);
+ phy_package_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_INTERNAL);
+ val = phy_package_read_paged(phydev, RTL821X_PAGE_PORT, reg[mac % 4]);
+ val |= BIT(10);
if (set_fibre) {
- pr_info("Powering on FIBRE");
- write_phy(base, 0xfff, 29, 3);
- /* Ensure power is off */
- read_phy(base, 0xa40, 16, &power);
- if (power & (1 << 11))
- write_phy(base, 0xa40, 16, power & ~(1 << 11));
+ val &= ~BIT(11);
} else {
- pr_info("Powering on COPPER\n");
- write_phy(base, 0xfff, 29, 1);
- /* Ensure power is off */
- read_phy(base, 0xa40, 16, &power);
- if (power & (1 << 11))
- write_phy(base, 0xa40, 16, power & ~(1 << 11));
+ val |= BIT(11);
}
- write_phy(base, 0xfff, 29, 0);
-}
-
-static bool rtl8380_rtl8214fc_media_is_fibre(int mac)
-{
- int base = mac - (mac % 4);
- static int reg[] = {16, 19, 20, 21};
- u32 val;
+ phy_package_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_INTERNAL);
+ phy_package_write_paged(phydev, RTL821X_PAGE_PORT, reg[mac % 4], val);
+ phy_package_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
- write_phy(base, 0xfff, 29, 8);
- read_phy(base, 0x266, reg[mac % 4], &val);
- write_phy(base, 0xfff, 29, 0);
- if (val & (1 << 11))
- return false;
- return true;
+ if (!phydev->suspended) {
+ if (set_fibre) {
+ rtl8214fc_power_set(phydev, PORT_MII, false);
+ rtl8214fc_power_set(phydev, PORT_FIBRE, true);
+ } else {
+ rtl8214fc_power_set(phydev, PORT_FIBRE, false);
+ rtl8214fc_power_set(phydev, PORT_MII, true);
+ }
+ }
}
static int rtl8214fc_set_port(struct phy_device *phydev, int port)
pr_debug("%s port %d to %d\n", __func__, addr, port);
- rtl8380_rtl8214fc_media_set(addr, is_fibre);
+ rtl8214fc_media_set(phydev, is_fibre);
return 0;
}
int addr = phydev->mdio.addr;
pr_debug("%s: port %d\n", __func__, addr);
- if (rtl8380_rtl8214fc_media_is_fibre(addr))
+ if (rtl8214fc_media_is_fibre(phydev))
return PORT_FIBRE;
return PORT_MII;
}
* but the only way that works since the kernel first enables EEE in the MAC
* and then sets up the PHY. The MAC-based approach would require the oppsite.
*/
-void rtl8218d_eee_set(int port, bool enable)
+void rtl8218d_eee_set(struct phy_device *phydev, bool enable)
{
u32 val;
bool an_enabled;
- pr_debug("In %s %d, enable %d\n", __func__, port, enable);
+ pr_debug("In %s %d, enable %d\n", __func__, phydev->mdio.addr, enable);
/* Set GPHY page to copper */
- write_phy(port, 0xa42, 30, 0x0001);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
- read_phy(port, 0, 0, &val);
+ val = phy_read(phydev, 0);
an_enabled = val & BIT(12);
/* Enable 100M (bit 1) / 1000M (bit 2) EEE */
- read_mmd_phy(port, 7, 60, &val);
+ val = phy_read_mmd(phydev, 7, 60);
val |= BIT(2) | BIT(1);
- write_mmd_phy(port, 7, 60, enable ? 0x6 : 0);
+ phy_write_mmd(phydev, 7, 60, enable ? 0x6 : 0);
/* 500M EEE ability */
- read_phy(port, 0xa42, 20, &val);
+ val = phy_read_paged(phydev, RTL821X_PAGE_GPHY, 20);
if (enable)
val |= BIT(7);
else
val &= ~BIT(7);
- write_phy(port, 0xa42, 20, val);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, 20, val);
/* Restart AN if enabled */
if (an_enabled) {
- read_phy(port, 0, 0, &val);
+ val = phy_read(phydev, 0);
val |= BIT(9);
- write_phy(port, 0, 0, val);
+ phy_write(phydev, 0, val);
}
/* GPHY page back to auto*/
- write_phy(port, 0xa42, 30, 0);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
}
static int rtl8218b_get_eee(struct phy_device *phydev,
pr_debug("In %s, port %d, was enabled: %d\n", __func__, addr, e->eee_enabled);
/* Set GPHY page to copper */
- write_phy(addr, 0xa42, 29, 0x0001);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
- read_phy(addr, 7, 60, &val);
+ val = phy_read_paged(phydev, 7, 60);
if (e->eee_enabled) {
// Verify vs MAC-based EEE
e->eee_enabled = !!(val & BIT(7));
if (!e->eee_enabled) {
- read_phy(addr, 0x0A43, 25, &val);
+ val = phy_read_paged(phydev, RTL821X_PAGE_MAC, 25);
e->eee_enabled = !!(val & BIT(4));
}
}
pr_debug("%s: enabled: %d\n", __func__, e->eee_enabled);
/* GPHY page to auto */
- write_phy(addr, 0xa42, 29, 0x0000);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
return 0;
}
pr_debug("In %s, port %d, was enabled: %d\n", __func__, addr, e->eee_enabled);
/* Set GPHY page to copper */
- write_phy(addr, 0xa42, 30, 0x0001);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
- read_phy(addr, 7, 60, &val);
+ val = phy_read_paged(phydev, 7, 60);
if (e->eee_enabled)
e->eee_enabled = !!(val & BIT(7));
pr_debug("%s: enabled: %d\n", __func__, e->eee_enabled);
/* GPHY page to auto */
- write_phy(addr, 0xa42, 30, 0x0000);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
return 0;
}
pr_debug("In %s port %d, enabled %d\n", __func__, port, e->eee_enabled);
- if (rtl8380_rtl8214fc_media_is_fibre(port)) {
+ if (rtl8214fc_media_is_fibre(phydev)) {
netdev_err(phydev->attached_dev, "Port %d configured for FIBRE", port);
return -ENOTSUPP;
}
poll_state = disable_polling(port);
/* Set GPHY page to copper */
- write_phy(port, 0xa42, 29, 0x0001);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
// Get auto-negotiation status
- read_phy(port, 0, 0, &val);
+ val = phy_read(phydev, 0);
an_enabled = val & BIT(12);
pr_info("%s: aneg: %d\n", __func__, an_enabled);
- read_phy(port, 0x0A43, 25, &val);
+ val = phy_read_paged(phydev, RTL821X_PAGE_MAC, 25);
val &= ~BIT(5); // Use MAC-based EEE
- write_phy(port, 0x0A43, 25, val);
+ phy_write_paged(phydev, RTL821X_PAGE_MAC, 25, val);
/* Enable 100M (bit 1) / 1000M (bit 2) EEE */
- write_phy(port, 7, 60, e->eee_enabled ? 0x6 : 0);
+ phy_write_paged(phydev, 7, 60, e->eee_enabled ? 0x6 : 0);
/* 500M EEE ability */
- read_phy(port, 0xa42, 20, &val);
+ val = phy_read_paged(phydev, RTL821X_PAGE_GPHY, 20);
if (e->eee_enabled)
val |= BIT(7);
else
val &= ~BIT(7);
- write_phy(port, 0xa42, 20, val);
+
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, 20, val);
/* Restart AN if enabled */
if (an_enabled) {
pr_info("%s: doing aneg\n", __func__);
- read_phy(port, 0, 0, &val);
+ val = phy_read(phydev, 0);
val |= BIT(9);
- write_phy(port, 0, 0, val);
+ phy_write(phydev, 0, val);
}
/* GPHY page back to auto*/
- write_phy(port, 0xa42, 29, 0);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
resume_polling(poll_state);
int addr = phydev->mdio.addr;
pr_debug("In %s port %d, enabled %d\n", __func__, addr, e->eee_enabled);
- if (rtl8380_rtl8214fc_media_is_fibre(addr)) {
+ if (rtl8214fc_media_is_fibre(phydev)) {
netdev_err(phydev->attached_dev, "Port %d configured for FIBRE", addr);
return -ENOTSUPP;
}
poll_state = disable_polling(port);
/* Set GPHY page to copper */
- write_phy(port, 0, 30, 0x0001);
- read_phy(port, 0, 0, &val);
+ phy_write(phydev, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
+ val = phy_read(phydev, 0);
an_enabled = val & BIT(12);
if (e->eee_enabled) {
/* 100/1000M EEE Capability */
- write_phy(port, 0, 13, 0x0007);
- write_phy(port, 0, 14, 0x003C);
- write_phy(port, 0, 13, 0x4007);
- write_phy(port, 0, 14, 0x0006);
+ phy_write(phydev, 13, 0x0007);
+ phy_write(phydev, 14, 0x003C);
+ phy_write(phydev, 13, 0x4007);
+ phy_write(phydev, 14, 0x0006);
- read_phy(port, 0x0A43, 25, &val);
+ val = phy_read_paged(phydev, RTL821X_PAGE_MAC, 25);
val |= BIT(4);
- write_phy(port, 0x0A43, 25, val);
+ phy_write_paged(phydev, RTL821X_PAGE_MAC, 25, val);
} else {
/* 100/1000M EEE Capability */
- write_phy(port, 0, 13, 0x0007);
- write_phy(port, 0, 14, 0x003C);
- write_phy(port, 0, 13, 0x0007);
- write_phy(port, 0, 14, 0x0000);
+ phy_write(phydev, 13, 0x0007);
+ phy_write(phydev, 14, 0x003C);
+ phy_write(phydev, 13, 0x0007);
+ phy_write(phydev, 14, 0x0000);
- read_phy(port, 0x0A43, 25, &val);
+ val = phy_read_paged(phydev, RTL821X_PAGE_MAC, 25);
val &= ~BIT(4);
- write_phy(port, 0x0A43, 25, val);
+ phy_write_paged(phydev, RTL821X_PAGE_MAC, 25, val);
}
/* Restart AN if enabled */
if (an_enabled) {
- read_phy(port, 0, 0, &val);
+ val = phy_read(phydev, 0);
val |= BIT(9);
- write_phy(port, 0, 0, val);
+ phy_write(phydev, 0, val);
}
/* GPHY page back to auto*/
- write_phy(port, 0xa42, 30, 0);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
pr_info("%s done\n", __func__);
resume_polling(poll_state);
poll_state = disable_polling(addr);
- rtl8218d_eee_set(addr, (bool) e->eee_enabled);
+ rtl8218d_eee_set(phydev, (bool) e->eee_enabled);
resume_polling(poll_state);
u32 phy_id, val;
int mac = phydev->mdio.addr;
- read_phy(mac, 0, 2, &val);
+ val = phy_read(phydev, 2);
phy_id = val << 16;
- read_phy(mac, 0, 3, &val);
+ val = phy_read(phydev, 3);
phy_id |= val;
pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
phydev_info(phydev, "Detected external RTL8214C\n");
/* GPHY auto conf */
- write_phy(mac, 0xa42, 29, 0);
+ phy_write_paged(phydev, RTL821X_PAGE_GPHY, RTL821XINT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
return 0;
}
u32 *rtl8380_rtl8214fc_perchip;
u32 *rtl8380_rtl8214fc_perport;
- read_phy(mac, 0, 2, &val);
+ val = phy_read(phydev, 2);
phy_id = val << 16;
- read_phy(mac, 0, 3, &val);
+ val = phy_read(phydev, 3);
phy_id |= val;
pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
/* Read internal PHY id */
- write_phy(mac, 0, 30, 0x0001);
- write_phy(mac, 0, 31, 0x0a42);
- write_phy(mac, 31, 27, 0x0002);
- read_phy(mac, 31, 28, &val);
+ phy_write_paged(phydev, 0, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
+ phy_write_paged(phydev, 0x1f, 0x1b, 0x0002);
+ val = phy_read_paged(phydev, 0x1f, 0x1c);
if (val != 0x6276) {
phydev_err(phydev, "Expected external RTL8214FC, found PHY-ID %x\n", val);
return -1;
+ h->parts[1].start;
/* detect phy version */
- write_phy(mac, 0xfff, 27, 0x0004);
- read_phy(mac, 0xfff, 28, &val);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, 27, 0x0004);
+ val = phy_read_paged(phydev, RTL83XX_PAGE_RAW, 28);
- read_phy(mac, 0, 16, &val);
+ val = phy_read(phydev, 16);
if (val & (1 << 11))
- rtl8380_rtl8214fc_on_off(mac, true);
+ rtl8380_rtl8214fc_on_off(phydev, true);
else
- rtl8380_phy_reset(mac);
+ rtl8380_phy_reset(phydev);
msleep(100);
- write_phy(mac, 0, 30, 0x0001);
+ phy_write_paged(phydev, 0, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
i = 0;
while (rtl8380_rtl8214fc_perchip[i * 3]
if (rtl8380_rtl8214fc_perchip[i * 3 + 1] == 0x1f)
page = rtl8380_rtl8214fc_perchip[i * 3 + 2];
if (rtl8380_rtl8214fc_perchip[i * 3 + 1] == 0x13 && page == 0x260) {
- read_phy(mac + rtl8380_rtl8214fc_perchip[i * 3], 0x260, 13, &val);
+ val = phy_read_paged(phydev, 0x260, 13);
val = (val & 0x1f00) | (rtl8380_rtl8214fc_perchip[i * 3 + 2]
& 0xe0ff);
- write_phy(mac + rtl8380_rtl8214fc_perchip[i * 3],
- 0xfff, rtl8380_rtl8214fc_perchip[i * 3 + 1], val);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW,
+ rtl8380_rtl8214fc_perchip[i * 3 + 1], val);
} else {
- write_phy(mac + rtl8380_rtl8214fc_perchip[i * 3],
- 0xfff, rtl8380_rtl8214fc_perchip[i * 3 + 1],
- rtl8380_rtl8214fc_perchip[i * 3 + 2]);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW,
+ rtl8380_rtl8214fc_perchip[i * 3 + 1],
+ rtl8380_rtl8214fc_perchip[i * 3 + 2]);
}
i++;
}
/* Force copper medium */
for (i = 0; i < 4; i++) {
- write_phy(mac + i, 0xfff, 0x1f, 0x0000);
- write_phy(mac + i, 0xfff, 0x1e, 0x0001);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL8XXX_PAGE_MAIN);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_COPPER);
}
/* Enable PHY */
for (i = 0; i < 4; i++) {
- write_phy(mac + i, 0xfff, 0x1f, 0x0000);
- write_phy(mac + i, 0xfff, 0x00, 0x1140);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL8XXX_PAGE_MAIN);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, 0x00, 0x1140);
}
mdelay(100);
/* Disable Autosensing */
for (i = 0; i < 4; i++) {
for (l = 0; l < 100; l++) {
- read_phy(mac + i, 0x0a42, 0x10, &val);
+ val = phy_package_port_read_paged(phydev, i, RTL821X_PAGE_GPHY, 0x10);
if ((val & 0x7) >= 3)
break;
}
/* Request patch */
for (i = 0; i < 4; i++) {
- write_phy(mac + i, 0xfff, 0x1f, 0x0b82);
- write_phy(mac + i, 0xfff, 0x10, 0x0010);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL821X_PAGE_PATCH);
+ phy_package_port_write_paged(phydev, i, RTL83XX_PAGE_RAW, 0x10, 0x0010);
}
mdelay(300);
/* Verify patch readiness */
for (i = 0; i < 4; i++) {
for (l = 0; l < 100; l++) {
- read_phy(mac + i, 0xb80, 0x10, &val);
+ val = phy_package_port_read_paged(phydev, i, RTL821X_PAGE_STATE, 0x10);
if (val & 0x40)
break;
}
return -1;
}
}
-
/* Use Broadcast ID method for patching */
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0008);
- write_phy(mac, 0xfff, 0x1f, 0x0266);
- write_phy(mac, 0xfff, 0x16, 0xff00 + mac);
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0000);
- mdelay(1);
+ rtl821x_phy_setup_package_broadcast(phydev, true);
i = 0;
while (rtl8380_rtl8214fc_perport[i * 2]) {
- write_phy(mac, 0xfff, rtl8380_rtl8214fc_perport[i * 2],
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, rtl8380_rtl8214fc_perport[i * 2],
rtl8380_rtl8214fc_perport[i * 2 + 1]);
i++;
}
/*Disable broadcast ID*/
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0008);
- write_phy(mac, 0xfff, 0x1f, 0x0266);
- write_phy(mac, 0xfff, 0x16, 0x00 + mac);
- write_phy(mac, 0xfff, 0x1f, 0x0000);
- write_phy(mac, 0xfff, 0x1d, 0x0000);
- mdelay(1);
+ rtl821x_phy_setup_package_broadcast(phydev, false);
/* Auto medium selection */
for (i = 0; i < 4; i++) {
- write_phy(mac + i, 0xfff, 0x1f, 0x0000);
- write_phy(mac + i, 0xfff, 0x1e, 0x0000);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL8XXX_PAGE_SELECT, RTL8XXX_PAGE_MAIN);
+ phy_write_paged(phydev, RTL83XX_PAGE_RAW, RTL821XEXT_MEDIA_PAGE_SELECT, RTL821X_MEDIA_PAGE_AUTO);
}
return 0;
return 0;
}
-int rtl9300_configure_serdes(struct phy_device *phydev)
+void rtl9300_sds_field_w(int sds, u32 page, u32 reg, int end_bit, int start_bit, u32 v)
{
- struct device *dev = &phydev->mdio.dev;
- int phy_addr = phydev->mdio.addr;
- int sds_num = 0;
- int v;
+ int l = end_bit - start_bit + 1;
+ u32 data = v;
- phydev_info(phydev, "Configuring internal RTL9300 SERDES\n");
+ if (l < 32) {
+ u32 mask = BIT(l) - 1;
- switch (phy_addr) {
- case 26:
- sds_num = 8;
- break;
- case 27:
- sds_num = 9;
- break;
- default:
- dev_err(dev, "Not a SerDes PHY\n");
- return -EINVAL;
+ data = rtl930x_read_sds_phy(sds, page, reg);
+ data &= ~(mask << start_bit);
+ data |= (v & mask) << start_bit;
}
- /* Set default Medium to fibre */
- v = rtl930x_read_sds_phy(sds_num, 0x1f, 11);
- if (v < 0) {
- dev_err(dev, "Cannot access SerDes PHY %d\n", phy_addr);
- return -EINVAL;
- }
- v |= BIT(2);
- rtl930x_write_sds_phy(sds_num, 0x1f, 11, v);
+ rtl930x_write_sds_phy(sds, page, reg, data);
+}
- // TODO: this needs to be configurable via ethtool/.dts
- pr_info("Setting 10G/1000BX auto fibre medium\n");
- rtl9300_sds_rst(sds_num, 0x1b);
+u32 rtl9300_sds_field_r(int sds, u32 page, u32 reg, int end_bit, int start_bit)
+{
+ int l = end_bit - start_bit + 1;
+ u32 v = rtl930x_read_sds_phy(sds, page, reg);
- // TODO: Apply patch set for fibre type
+ if (l >= 32)
+ return v;
- return 0;
+ return (v >> start_bit) & (BIT(l) - 1);
}
-static int rtl8214fc_phy_probe(struct phy_device *phydev)
+/* Read the link and speed status of the internal SerDes of the RTL9300
+ */
+static int rtl9300_read_status(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
+ int phy_addr = phydev->mdio.addr;
+ struct device_node *dn;
+ u32 sds_num = 0, status, latch_status, mode;
- /* 839x has internal SerDes */
- if (soc_info.id == 0x8393)
- return -ENODEV;
+ if (dev->of_node) {
+ dn = dev->of_node;
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ if (of_property_read_u32(dn, "sds", &sds_num))
+ sds_num = -1;
+ pr_info("%s: Port %d, SerDes is %d\n", __func__, phy_addr, sds_num);
+ } else {
+ dev_err(dev, "No DT node.\n");
+ return -EINVAL;
+ }
- priv->name = "RTL8214FC";
+ if (sds_num < 0)
+ return 0;
- /* All base addresses of the PHYs start at multiples of 8 */
- if (!(addr % 8)) {
- /* Configuration must be done whil patching still possible */
- return rtl8380_configure_rtl8214fc(phydev);
+ mode = rtl9300_sds_mode_get(sds_num);
+ pr_info("%s got SDS mode %02x\n", __func__, mode);
+ if (mode == 0x1a) { // 10GR mode
+ status = rtl9300_sds_field_r(sds_num, 0x5, 0, 12, 12);
+ latch_status = rtl9300_sds_field_r(sds_num, 0x4, 1, 2, 2);
+ status |= rtl9300_sds_field_r(sds_num, 0x5, 0, 12, 12);
+ latch_status |= rtl9300_sds_field_r(sds_num, 0x4, 1, 2, 2);
+ } else {
+ status = rtl9300_sds_field_r(sds_num, 0x1, 29, 8, 0);
+ latch_status = rtl9300_sds_field_r(sds_num, 0x1, 30, 8, 0);
+ status |= rtl9300_sds_field_r(sds_num, 0x1, 29, 8, 0);
+ latch_status |= rtl9300_sds_field_r(sds_num, 0x1, 30, 8, 0);
}
- return 0;
-}
-
-static int rtl8214c_phy_probe(struct phy_device *phydev)
-{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ pr_info("%s link status: status: %d, latch %d\n", __func__, status, latch_status);
- priv->name = "RTL8214C";
+ if (latch_status) {
+ phydev->link = true;
+ if (mode == 0x1a)
+ phydev->speed = SPEED_10000;
+ else
+ phydev->speed = SPEED_1000;
- /* All base addresses of the PHYs start at multiples of 8 */
- if (!(addr % 8)) {
- /* Configuration must be done whil patching still possible */
- return rtl8380_configure_rtl8214c(phydev);
+ phydev->duplex = DUPLEX_FULL;
}
+
return 0;
}
-static int rtl8218b_ext_phy_probe(struct phy_device *phydev)
+void rtl930x_sds_rx_rst(int sds_num, phy_interface_t phy_if)
{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
+ int page = 0x2e; // 10GR and USXGMII
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ if (phy_if == PHY_INTERFACE_MODE_1000BASEX)
+ page = 0x24;
- priv->name = "RTL8218B (external)";
-
- /* All base addresses of the PHYs start at multiples of 8 */
- if (!(addr % 8) && soc_info.family == RTL8380_FAMILY_ID) {
- /* Configuration must be done while patching still possible */
- return rtl8380_configure_ext_rtl8218b(phydev);
- }
- return 0;
+ rtl9300_sds_field_w(sds_num, page, 0x15, 4, 4, 0x1);
+ mdelay(5);
+ rtl9300_sds_field_w(sds_num, page, 0x15, 4, 4, 0x0);
}
-static int rtl8218b_int_phy_probe(struct phy_device *phydev)
+/*
+ * Force PHY modes on 10GBit Serdes
+ */
+void rtl9300_force_sds_mode(int sds, phy_interface_t phy_if)
{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
+ int sds_mode;
+ bool lc_on;
+ int i, lc_value;
+ int lane_0 = (sds % 2) ? sds - 1 : sds;
+ u32 v, cr_0, cr_1, cr_2;
+ u32 m_bit, l_bit;
+
+ pr_info("%s: SDS: %d, mode %d\n", __func__, sds, phy_if);
+ switch (phy_if) {
+ case PHY_INTERFACE_MODE_SGMII:
+ sds_mode = 0x2;
+ lc_on = false;
+ lc_value = 0x1;
+ break;
- if (soc_info.family != RTL8380_FAMILY_ID)
- return -ENODEV;
- if (addr >= 24)
- return -ENODEV;
+ case PHY_INTERFACE_MODE_HSGMII:
+ sds_mode = 0x12;
+ lc_value = 0x3;
+ // Configure LC
+ break;
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ case PHY_INTERFACE_MODE_1000BASEX:
+ sds_mode = 0x04;
+ lc_on = false;
+ break;
- priv->name = "RTL8218B (internal)";
+ case PHY_INTERFACE_MODE_2500BASEX:
+ sds_mode = 0x16;
+ lc_value = 0x3;
+ // Configure LC
+ break;
- /* All base addresses of the PHYs start at multiples of 8 */
- if (!(addr % 8)) {
- /* Configuration must be done while patching still possible */
- return rtl8380_configure_int_rtl8218b(phydev);
+ case PHY_INTERFACE_MODE_10GBASER:
+ sds_mode = 0x1a;
+ lc_on = true;
+ lc_value = 0x5;
+ break;
+
+ case PHY_INTERFACE_MODE_NA:
+ // This will disable SerDes
+ sds_mode = 0x1f;
+ break;
+
+ default:
+ pr_err("%s: unknown serdes mode: %s\n",
+ __func__, phy_modes(phy_if));
+ return;
}
- return 0;
-}
-static int rtl8218d_phy_probe(struct phy_device *phydev)
-{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
+ pr_info("%s --------------------- serdes %d forcing to %x ...\n", __func__, sds, sds_mode);
+ // Power down SerDes
+ rtl9300_sds_field_w(sds, 0x20, 0, 7, 6, 0x3);
+ if (sds == 5) pr_info("%s after %x\n", __func__, rtl930x_read_sds_phy(sds, 0x20, 0));
- pr_debug("%s: id: %d\n", __func__, addr);
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ if (sds == 5) pr_info("%s a %x\n", __func__, rtl930x_read_sds_phy(sds, 0x1f, 9));
+ // Force mode enable
+ rtl9300_sds_field_w(sds, 0x1f, 9, 6, 6, 0x1);
+ if (sds == 5) pr_info("%s b %x\n", __func__, rtl930x_read_sds_phy(sds, 0x1f, 9));
- priv->name = "RTL8218D";
+ /* SerDes off */
+ rtl9300_sds_field_w(sds, 0x1f, 9, 11, 7, 0x1f);
- /* All base addresses of the PHYs start at multiples of 8 */
- if (!(addr % 8)) {
- /* Configuration must be done while patching still possible */
-// TODO: return configure_rtl8218d(phydev);
- }
- return 0;
-}
+ if (phy_if == PHY_INTERFACE_MODE_NA)
+ return;
-static int rtl8226_phy_probe(struct phy_device *phydev)
-{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
+ if (sds == 5) pr_info("%s c %x\n", __func__, rtl930x_read_sds_phy(sds, 0x20, 18));
+ // Enable LC and ring
+ rtl9300_sds_field_w(lane_0, 0x20, 18, 3, 0, 0xf);
- pr_info("%s: id: %d\n", __func__, addr);
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ if (sds == lane_0)
+ rtl9300_sds_field_w(lane_0, 0x20, 18, 5, 4, 0x1);
+ else
+ rtl9300_sds_field_w(lane_0, 0x20, 18, 7, 6, 0x1);
- priv->name = "RTL8226";
+ rtl9300_sds_field_w(sds, 0x20, 0, 5, 4, 0x3);
- return 0;
-}
+ if (lc_on)
+ rtl9300_sds_field_w(lane_0, 0x20, 18, 11, 8, lc_value);
+ else
+ rtl9300_sds_field_w(lane_0, 0x20, 18, 15, 12, lc_value);
-static int rtl838x_serdes_probe(struct phy_device *phydev)
-{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
+ // Force analog LC & ring on
+ rtl9300_sds_field_w(lane_0, 0x21, 11, 3, 0, 0xf);
- if (soc_info.family != RTL8380_FAMILY_ID)
+ v = lc_on ? 0x3 : 0x1;
+
+ if (sds == lane_0)
+ rtl9300_sds_field_w(lane_0, 0x20, 18, 5, 4, v);
+ else
+ rtl9300_sds_field_w(lane_0, 0x20, 18, 7, 6, v);
+
+ // Force SerDes mode
+ rtl9300_sds_field_w(sds, 0x1f, 9, 6, 6, 1);
+ rtl9300_sds_field_w(sds, 0x1f, 9, 11, 7, sds_mode);
+
+ // Toggle LC or Ring
+ for (i = 0; i < 20; i++) {
+ mdelay(200);
+
+ rtl930x_write_sds_phy(lane_0, 0x1f, 2, 53);
+
+ m_bit = (lane_0 == sds) ? (4) : (5);
+ l_bit = (lane_0 == sds) ? (4) : (5);
+
+ cr_0 = rtl9300_sds_field_r(lane_0, 0x1f, 20, m_bit, l_bit);
+ mdelay(10);
+ cr_1 = rtl9300_sds_field_r(lane_0, 0x1f, 20, m_bit, l_bit);
+ mdelay(10);
+ cr_2 = rtl9300_sds_field_r(lane_0, 0x1f, 20, m_bit, l_bit);
+
+ if (cr_0 && cr_1 && cr_2) {
+ u32 t;
+ if (phy_if != PHY_INTERFACE_MODE_10GBASER)
+ break;
+
+ t = rtl9300_sds_field_r(sds, 0x6, 0x1, 2, 2);
+ rtl9300_sds_field_w(sds, 0x6, 0x1, 2, 2, 0x1);
+
+ // Reset FSM
+ rtl9300_sds_field_w(sds, 0x6, 0x2, 12, 12, 0x1);
+ mdelay(10);
+ rtl9300_sds_field_w(sds, 0x6, 0x2, 12, 12, 0x0);
+ mdelay(10);
+
+ // Need to read this twice
+ v = rtl9300_sds_field_r(sds, 0x5, 0, 12, 12);
+ v = rtl9300_sds_field_r(sds, 0x5, 0, 12, 12);
+
+ rtl9300_sds_field_w(sds, 0x6, 0x1, 2, 2, t);
+
+ // Reset FSM again
+ rtl9300_sds_field_w(sds, 0x6, 0x2, 12, 12, 0x1);
+ mdelay(10);
+ rtl9300_sds_field_w(sds, 0x6, 0x2, 12, 12, 0x0);
+ mdelay(10);
+
+ if (v == 1)
+ break;
+ }
+
+ m_bit = (phy_if == PHY_INTERFACE_MODE_10GBASER) ? 3 : 1;
+ l_bit = (phy_if == PHY_INTERFACE_MODE_10GBASER) ? 2 : 0;
+
+ rtl9300_sds_field_w(lane_0, 0x21, 11, m_bit, l_bit, 0x2);
+ mdelay(10);
+ rtl9300_sds_field_w(lane_0, 0x21, 11, m_bit, l_bit, 0x3);
+ }
+
+ rtl930x_sds_rx_rst(sds, phy_if);
+
+ // Re-enable power
+ rtl9300_sds_field_w(sds, 0x20, 0, 7, 6, 0);
+
+ pr_info("%s --------------------- serdes %d forced to %x DONE\n", __func__, sds, sds_mode);
+}
+
+void rtl9300_sds_tx_config(int sds, phy_interface_t phy_if)
+{
+ // parameters: rtl9303_80G_txParam_s2
+ int impedance = 0x8;
+ int pre_amp = 0x2;
+ int main_amp = 0x9;
+ int post_amp = 0x2;
+ int pre_en = 0x1;
+ int post_en = 0x1;
+ int page;
+
+ switch(phy_if) {
+ case PHY_INTERFACE_MODE_1000BASEX:
+ page = 0x25;
+ break;
+ case PHY_INTERFACE_MODE_HSGMII:
+ case PHY_INTERFACE_MODE_2500BASEX:
+ page = 0x29;
+ break;
+ case PHY_INTERFACE_MODE_10GBASER:
+ page = 0x2f;
+ break;
+ default:
+ pr_err("%s: unsupported PHY mode\n", __func__);
+ return;
+ }
+
+ rtl9300_sds_field_w(sds, page, 0x1, 15, 11, pre_amp);
+ rtl9300_sds_field_w(sds, page, 0x7, 0, 0, pre_en);
+ rtl9300_sds_field_w(sds, page, 0x7, 8, 4, main_amp);
+ rtl9300_sds_field_w(sds, page, 0x6, 4, 0, post_amp);
+ rtl9300_sds_field_w(sds, page, 0x7, 3, 3, post_en);
+ rtl9300_sds_field_w(sds, page, 0x18, 15, 12, impedance);
+}
+
+/*
+ * Wait for clock ready, this assumes the SerDes is in XGMII mode
+ * timeout is in ms
+ */
+int rtl9300_sds_clock_wait(int timeout)
+{
+ u32 v;
+ unsigned long start = jiffies;
+
+ do {
+ rtl9300_sds_field_w(2, 0x1f, 0x2, 15, 0, 53);
+ v = rtl9300_sds_field_r(2, 0x1f, 20, 5, 4);
+ if (v == 3)
+ return 0;
+ } while (jiffies < start + (HZ / 1000) * timeout);
+
+ return 1;
+}
+
+void rtl9300_serdes_mac_link_config(int sds, bool tx_normal, bool rx_normal)
+{
+ u32 v10, v1;
+
+ v10 = rtl930x_read_sds_phy(sds, 6, 2); // 10GBit, page 6, reg 2
+ v1 = rtl930x_read_sds_phy(sds, 0, 0); // 1GBit, page 0, reg 0
+ pr_info("%s: registers before %08x %08x\n", __func__, v10, v1);
+
+ v10 &= ~(BIT(13) | BIT(14));
+ v1 &= ~(BIT(8) | BIT(9));
+
+ v10 |= rx_normal ? 0 : BIT(13);
+ v1 |= rx_normal ? 0 : BIT(9);
+
+ v10 |= tx_normal ? 0 : BIT(14);
+ v1 |= tx_normal ? 0 : BIT(8);
+
+ rtl930x_write_sds_phy(sds, 6, 2, v10);
+ rtl930x_write_sds_phy(sds, 0, 0, v1);
+
+ v10 = rtl930x_read_sds_phy(sds, 6, 2);
+ v1 = rtl930x_read_sds_phy(sds, 0, 0);
+ pr_info("%s: registers after %08x %08x\n", __func__, v10, v1);
+}
+
+void rtl9300_sds_rxcal_dcvs_manual(u32 sds_num, u32 dcvs_id, bool manual, u32 dvcs_list[])
+{
+ if (manual) {
+ switch(dcvs_id) {
+ case 0:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 14, 14, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 5, 5, dvcs_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 4, 0, dvcs_list[1]);
+ break;
+ case 1:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 13, 13, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 15, 15, dvcs_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 14, 11, dvcs_list[1]);
+ break;
+ case 2:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 12, 12, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 10, 10, dvcs_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 9, 6, dvcs_list[1]);
+ break;
+ case 3:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 11, 11, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 5, 5, dvcs_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1d, 4, 1, dvcs_list[1]);
+ break;
+ case 4:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x01, 15, 15, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 10, 10, dvcs_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 9, 6, dvcs_list[1]);
+ break;
+ case 5:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x02, 11, 11, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 4, 4, dvcs_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x11, 3, 0, dvcs_list[1]);
+ break;
+ default:
+ break;
+ }
+ } else {
+ switch(dcvs_id) {
+ case 0:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 14, 14, 0x0);
+ break;
+ case 1:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 13, 13, 0x0);
+ break;
+ case 2:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 12, 12, 0x0);
+ break;
+ case 3:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x1e, 11, 11, 0x0);
+ break;
+ case 4:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x01, 15, 15, 0x0);
+ break;
+ case 5:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x02, 11, 11, 0x0);
+ break;
+ default:
+ break;
+ }
+ mdelay(1);
+ }
+}
+
+void rtl9300_sds_rxcal_dcvs_get(u32 sds_num, u32 dcvs_id, u32 dcvs_list[])
+{
+ u32 dcvs_sign_out = 0, dcvs_coef_bin = 0;
+ bool dcvs_manual;
+
+ if (!(sds_num % 2))
+ rtl930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
+ else
+ rtl930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
+
+ // ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1]
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
+
+ // ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x]
+ rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
+
+ switch(dcvs_id) {
+ case 0:
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x22);
+ mdelay(1);
+
+ // ##DCVS0 Read Out
+ dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
+ dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
+ dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 14, 14);
+ break;
+
+ case 1:
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x23);
+ mdelay(1);
+
+ // ##DCVS0 Read Out
+ dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
+ dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
+ dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 13, 13);
+ break;
+
+ case 2:
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x24);
+ mdelay(1);
+
+ // ##DCVS0 Read Out
+ dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
+ dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
+ dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 12, 12);
+ break;
+ case 3:
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x25);
+ mdelay(1);
+
+ // ##DCVS0 Read Out
+ dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
+ dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
+ dcvs_manual = rtl9300_sds_field_r(sds_num, 0x2e, 0x1e, 11, 11);
+ break;
+
+ case 4:
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x2c);
+ mdelay(1);
+
+ // ##DCVS0 Read Out
+ dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
+ dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
+ dcvs_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x01, 15, 15);
+ break;
+
+ case 5:
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0x2d);
+ mdelay(1);
+
+ // ##DCVS0 Read Out
+ dcvs_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 4);
+ dcvs_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 3, 0);
+ dcvs_manual = rtl9300_sds_field_r(sds_num, 0x2e, 0x02, 11, 11);
+ break;
+
+ default:
+ break;
+ }
+
+ if (dcvs_sign_out)
+ pr_info("%s DCVS %u Sign: -", __func__, dcvs_id);
+ else
+ pr_info("%s DCVS %u Sign: +", __func__, dcvs_id);
+
+ pr_info("DCVS %u even coefficient = %u", dcvs_id, dcvs_coef_bin);
+ pr_info("DCVS %u manual = %u", dcvs_id, dcvs_manual);
+
+ dcvs_list[0] = dcvs_sign_out;
+ dcvs_list[1] = dcvs_coef_bin;
+}
+
+void rtl9300_sds_rxcal_leq_manual(u32 sds_num, bool manual, u32 leq_gray)
+{
+ if (manual) {
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x18, 15, 15, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x16, 14, 10, leq_gray);
+ } else {
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x18, 15, 15, 0x0);
+ mdelay(100);
+ }
+}
+
+void rtl9300_sds_rxcal_leq_offset_manual(u32 sds_num, bool manual, u32 offset)
+{
+ if (manual) {
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 6, 2, offset);
+ } else {
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 6, 2, offset);
+ mdelay(1);
+ }
+}
+
+#define GRAY_BITS 5
+u32 rtl9300_sds_rxcal_gray_to_binary(u32 gray_code)
+{
+ int i, j, m;
+ u32 g[GRAY_BITS];
+ u32 c[GRAY_BITS];
+ u32 leq_binary = 0;
+
+ for(i = 0; i < GRAY_BITS; i++)
+ g[i] = (gray_code & BIT(i)) >> i;
+
+ m = GRAY_BITS - 1;
+
+ c[m] = g[m];
+
+ for(i = 0; i < m; i++) {
+ c[i] = g[i];
+ for(j = i + 1; j < GRAY_BITS; j++)
+ c[i] = c[i] ^ g[j];
+ }
+
+ for(i = 0; i < GRAY_BITS; i++)
+ leq_binary += c[i] << i;
+
+ return leq_binary;
+}
+
+u32 rtl9300_sds_rxcal_leq_read(int sds_num)
+{
+ u32 leq_gray, leq_bin;
+ bool leq_manual;
+
+ if (!(sds_num % 2))
+ rtl930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
+ else
+ rtl930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
+
+ // ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1]
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
+
+ // ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[0 1 x x x x]
+ rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x10);
+ mdelay(1);
+
+ // ##LEQ Read Out
+ leq_gray = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 7, 3);
+ leq_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x18, 15, 15);
+ leq_bin = rtl9300_sds_rxcal_gray_to_binary(leq_gray);
+
+ pr_info("LEQ_gray: %u, LEQ_bin: %u", leq_gray, leq_bin);
+ pr_info("LEQ manual: %u", leq_manual);
+
+ return leq_bin;
+}
+
+void rtl9300_sds_rxcal_vth_manual(u32 sds_num, bool manual, u32 vth_list[])
+{
+ if (manual) {
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, 13, 13, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x13, 5, 3, vth_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x13, 2, 0, vth_list[1]);
+ } else {
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, 13, 13, 0x0);
+ mdelay(10);
+ }
+}
+
+void rtl9300_sds_rxcal_vth_get(u32 sds_num, u32 vth_list[])
+{
+ u32 vth_manual;
+
+ //##Page0x1F, Reg0x02[15 0], REG_DBGO_SEL=[0x002F]; //Lane0
+ //##Page0x1F, Reg0x02[15 0], REG_DBGO_SEL=[0x0031]; //Lane1
+ if (!(sds_num % 2))
+ rtl930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
+ else
+ rtl930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
+
+ //##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1]
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
+ //##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x]
+ rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
+ //##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 1 1 0 0]
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0xc);
+
+ mdelay(1);
+
+ //##VthP & VthN Read Out
+ vth_list[0] = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 2, 0); // v_thp set bin
+ vth_list[1] = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 3); // v_thn set bin
+
+ pr_info("vth_set_bin = %d", vth_list[0]);
+ pr_info("vth_set_bin = %d", vth_list[1]);
+
+ vth_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x0f, 13, 13);
+ pr_info("Vth Maunal = %d", vth_manual);
+}
+
+void rtl9300_sds_rxcal_tap_manual(u32 sds_num, int tap_id, bool manual, u32 tap_list[])
+{
+ if (manual) {
+ switch(tap_id) {
+ case 0:
+ //##REG0_LOAD_IN_INIT[0]=1; REG0_TAP0_INIT[5:0]=Tap0_Value
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 5, 5, tap_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x03, 4, 0, tap_list[1]);
+ break;
+ case 1:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x21, 0x07, 6, 6, tap_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x09, 11, 6, tap_list[1]);
+ rtl9300_sds_field_w(sds_num, 0x21, 0x07, 5, 5, tap_list[2]);
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x12, 5, 0, tap_list[3]);
+ break;
+ case 2:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x09, 5, 5, tap_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x09, 4, 0, tap_list[1]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 11, 11, tap_list[2]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 10, 6, tap_list[3]);
+ break;
+ case 3:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 5, 5, tap_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0a, 4, 0, tap_list[1]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 5, 5, tap_list[2]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 4, 0, tap_list[3]);
+ break;
+ case 4:
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x1);
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x01, 5, 5, tap_list[0]);
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x01, 4, 0, tap_list[1]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 11, 11, tap_list[2]);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x06, 10, 6, tap_list[3]);
+ break;
+ default:
+ break;
+ }
+ } else {
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7, 0x0);
+ mdelay(10);
+ }
+}
+
+void rtl9300_sds_rxcal_tap_get(u32 sds_num, u32 tap_id, u32 tap_list[])
+{
+ u32 tap0_sign_out;
+ u32 tap0_coef_bin;
+ u32 tap_sign_out_even;
+ u32 tap_coef_bin_even;
+ u32 tap_sign_out_odd;
+ u32 tap_coef_bin_odd;
+ bool tap_manual;
+
+ if (!(sds_num % 2))
+ rtl930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
+ else
+ rtl930x_write_sds_phy(sds_num - 1, 0x1f, 0x2, 0x31);
+
+ //##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1]
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
+ //##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x]
+ rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
+
+ if (!tap_id) {
+ //##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 0 0 0 1]
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0);
+ //##Tap1 Even Read Out
+ mdelay(1);
+ tap0_sign_out = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 5);
+ tap0_coef_bin = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 0);
+
+ if (tap0_sign_out == 1)
+ pr_info("Tap0 Sign : -");
+ else
+ pr_info("Tap0 Sign : +");
+
+ pr_info("tap0_coef_bin = %d", tap0_coef_bin);
+
+ tap_list[0] = tap0_sign_out;
+ tap_list[1] = tap0_coef_bin;
+
+ tap_manual = !!rtl9300_sds_field_r(sds_num, 0x2e, 0x0f, 7, 7);
+ pr_info("tap0 manual = %u",tap_manual);
+ } else {
+ //##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 0 0 0 1]
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, tap_id);
+ mdelay(1);
+ //##Tap1 Even Read Out
+ tap_sign_out_even = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 5);
+ tap_coef_bin_even = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 0);
+
+ //##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 0 1 1 0]
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, (tap_id + 5));
+ //##Tap1 Odd Read Out
+ tap_sign_out_odd = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 5);
+ tap_coef_bin_odd = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 4, 0);
+
+ if (tap_sign_out_even == 1)
+ pr_info("Tap %u even sign: -", tap_id);
+ else
+ pr_info("Tap %u even sign: +", tap_id);
+
+ pr_info("Tap %u even coefficient = %u", tap_id, tap_coef_bin_even);
+
+ if (tap_sign_out_odd == 1)
+ pr_info("Tap %u odd sign: -", tap_id);
+ else
+ pr_info("Tap %u odd sign: +", tap_id);
+
+ pr_info("Tap %u odd coefficient = %u", tap_id,tap_coef_bin_odd);
+
+ tap_list[0] = tap_sign_out_even;
+ tap_list[1] = tap_coef_bin_even;
+ tap_list[2] = tap_sign_out_odd;
+ tap_list[3] = tap_coef_bin_odd;
+
+ tap_manual = rtl9300_sds_field_r(sds_num, 0x2e, 0x0f, tap_id + 7, tap_id + 7);
+ pr_info("tap %u manual = %d",tap_id, tap_manual);
+ }
+}
+
+void rtl9300_do_rx_calibration_1(int sds, phy_interface_t phy_mode)
+{
+ // From both rtl9300_rxCaliConf_serdes_myParam and rtl9300_rxCaliConf_phy_myParam
+ int tap0_init_val = 0x1f; // Initial Decision Fed Equalizer 0 tap
+ int vth_min = 0x0;
+
+ pr_info("start_1.1.1 initial value for sds %d\n", sds);
+ rtl930x_write_sds_phy(sds, 6, 0, 0);
+
+ // FGCAL
+ rtl9300_sds_field_w(sds, 0x2e, 0x01, 14, 14, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x1c, 10, 5, 0x20);
+ rtl9300_sds_field_w(sds, 0x2f, 0x02, 0, 0, 0x1);
+
+ // DCVS
+ rtl9300_sds_field_w(sds, 0x2e, 0x1e, 14, 11, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x01, 15, 15, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x02, 11, 11, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x1c, 4, 0, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x1d, 15, 11, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x1d, 10, 6, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x1d, 5, 1, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x02, 10, 6, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x11, 4, 0, 0x0);
+ rtl9300_sds_field_w(sds, 0x2f, 0x00, 3, 0, 0xf);
+ rtl9300_sds_field_w(sds, 0x2e, 0x04, 6, 6, 0x1);
+ rtl9300_sds_field_w(sds, 0x2e, 0x04, 7, 7, 0x1);
+
+ // LEQ (Long Term Equivalent signal level)
+ rtl9300_sds_field_w(sds, 0x2e, 0x16, 14, 8, 0x0);
+
+ // DFE (Decision Fed Equalizer)
+ rtl9300_sds_field_w(sds, 0x2f, 0x03, 5, 0, tap0_init_val);
+ rtl9300_sds_field_w(sds, 0x2e, 0x09, 11, 6, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x09, 5, 0, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x0a, 5, 0, 0x0);
+ rtl9300_sds_field_w(sds, 0x2f, 0x01, 5, 0, 0x0);
+ rtl9300_sds_field_w(sds, 0x2f, 0x12, 5, 0, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x0a, 11, 6, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x06, 5, 0, 0x0);
+ rtl9300_sds_field_w(sds, 0x2f, 0x01, 5, 0, 0x0);
+
+ // Vth
+ rtl9300_sds_field_w(sds, 0x2e, 0x13, 5, 3, 0x7);
+ rtl9300_sds_field_w(sds, 0x2e, 0x13, 2, 0, 0x7);
+ rtl9300_sds_field_w(sds, 0x2f, 0x0b, 5, 3, vth_min);
+
+ pr_info("end_1.1.1 --\n");
+
+ pr_info("start_1.1.2 Load DFE init. value\n");
+
+ rtl9300_sds_field_w(sds, 0x2e, 0x0f, 13, 7, 0x7f);
+
+ pr_info("end_1.1.2\n");
+
+ pr_info("start_1.1.3 disable LEQ training,enable DFE clock\n");
+
+ rtl9300_sds_field_w(sds, 0x2e, 0x17, 7, 7, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x17, 6, 2, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x0c, 8, 8, 0x0);
+ rtl9300_sds_field_w(sds, 0x2e, 0x0b, 4, 4, 0x1);
+ rtl9300_sds_field_w(sds, 0x2e, 0x12, 14, 14, 0x0);
+ rtl9300_sds_field_w(sds, 0x2f, 0x02, 15, 15, 0x0);
+
+ pr_info("end_1.1.3 --\n");
+
+ pr_info("start_1.1.4 offset cali setting\n");
+
+ rtl9300_sds_field_w(sds, 0x2e, 0x0f, 15, 14, 0x3);
+
+ pr_info("end_1.1.4\n");
+
+ pr_info("start_1.1.5 LEQ and DFE setting\n");
+
+ // TODO: make this work for DAC cables of different lengths
+ // For a 10GBit serdes wit Fibre, SDS 8 or 9
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER || PHY_INTERFACE_MODE_1000BASEX)
+ rtl9300_sds_field_w(sds, 0x2e, 0x16, 3, 2, 0x2);
+ else
+ pr_err("%s not PHY-based or SerDes, implement DAC!\n", __func__);
+
+ // No serdes, check for Aquantia PHYs
+ rtl9300_sds_field_w(sds, 0x2e, 0x16, 3, 2, 0x2);
+
+ rtl9300_sds_field_w(sds, 0x2e, 0x0f, 6, 0, 0x5f);
+ rtl9300_sds_field_w(sds, 0x2f, 0x05, 7, 2, 0x1f);
+ rtl9300_sds_field_w(sds, 0x2e, 0x19, 9, 5, 0x1f);
+ rtl9300_sds_field_w(sds, 0x2f, 0x0b, 15, 9, 0x3c);
+ rtl9300_sds_field_w(sds, 0x2e, 0x0b, 1, 0, 0x3);
+
+ pr_info("end_1.1.5\n");
+}
+
+void rtl9300_do_rx_calibration_2_1(u32 sds_num)
+{
+ pr_info("start_1.2.1 ForegroundOffsetCal_Manual\n");
+
+ // Gray config endis to 1
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x02, 2, 2, 0x1);
+
+ // ForegroundOffsetCal_Manual(auto mode)
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x01, 14, 14, 0x0);
+
+ pr_info("end_1.2.1");
+}
+
+void rtl9300_do_rx_calibration_2_2(int sds_num)
+{
+ //Force Rx-Run = 0
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 8, 8, 0x0);
+
+ rtl930x_sds_rx_rst(sds_num, PHY_INTERFACE_MODE_10GBASER);
+}
+
+void rtl9300_do_rx_calibration_2_3(int sds_num)
+{
+ u32 fgcal_binary, fgcal_gray;
+ u32 offset_range;
+
+ pr_info("start_1.2.3 Foreground Calibration\n");
+
+ while(1) {
+ if (!(sds_num % 2))
+ rtl930x_write_sds_phy(sds_num, 0x1f, 0x2, 0x2f);
+ else
+ rtl930x_write_sds_phy(sds_num -1 , 0x1f, 0x2, 0x31);
+
+ // ##Page0x2E, Reg0x15[9], REG0_RX_EN_TEST=[1]
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 9, 9, 0x1);
+ // ##Page0x21, Reg0x06[11 6], REG0_RX_DEBUG_SEL=[1 0 x x x x]
+ rtl9300_sds_field_w(sds_num, 0x21, 0x06, 11, 6, 0x20);
+ // ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 1 1 1 1]
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0xf);
+ // ##FGCAL read gray
+ fgcal_gray = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 0);
+ // ##Page0x2F, Reg0x0C[5 0], REG0_COEF_SEL=[0 0 1 1 1 0]
+ rtl9300_sds_field_w(sds_num, 0x2f, 0x0c, 5, 0, 0xe);
+ // ##FGCAL read binary
+ fgcal_binary = rtl9300_sds_field_r(sds_num, 0x1f, 0x14, 5, 0);
+
+ pr_info("%s: fgcal_gray: %d, fgcal_binary %d\n",
+ __func__, fgcal_gray, fgcal_binary);
+
+ offset_range = rtl9300_sds_field_r(sds_num, 0x2e, 0x15, 15, 14);
+
+ if (fgcal_binary > 60 || fgcal_binary < 3) {
+ if (offset_range == 3) {
+ pr_info("%s: Foreground Calibration result marginal!", __func__);
+ break;
+ } else {
+ offset_range++;
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x15, 15, 14, offset_range);
+ rtl9300_do_rx_calibration_2_2(sds_num);
+ }
+ } else {
+ break;
+ }
+ }
+ pr_info("%s: end_1.2.3\n", __func__);
+}
+
+void rtl9300_do_rx_calibration_2(int sds)
+{
+ rtl930x_sds_rx_rst(sds, PHY_INTERFACE_MODE_10GBASER);
+ rtl9300_do_rx_calibration_2_1(sds);
+ rtl9300_do_rx_calibration_2_2(sds);
+ rtl9300_do_rx_calibration_2_3(sds);
+}
+
+void rtl9300_sds_rxcal_3_1(int sds_num, phy_interface_t phy_mode)
+{
+ pr_info("start_1.3.1");
+
+ // ##1.3.1
+ if (phy_mode != PHY_INTERFACE_MODE_10GBASER && phy_mode != PHY_INTERFACE_MODE_1000BASEX)
+ rtl9300_sds_field_w(sds_num, 0x2e, 0xc, 8, 8, 0);
+
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, 0x0);
+ rtl9300_sds_rxcal_leq_manual(sds_num, false, 0);
+
+ pr_info("end_1.3.1");
+}
+
+void rtl9300_sds_rxcal_3_2(int sds_num, phy_interface_t phy_mode)
+{
+ u32 sum10 = 0, avg10, int10;
+ int dac_long_cable_offset;
+ bool eq_hold_enabled;
+ int i;
+
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER || phy_mode == PHY_INTERFACE_MODE_1000BASEX) {
+ // rtl9300_rxCaliConf_serdes_myParam
+ dac_long_cable_offset = 3;
+ eq_hold_enabled = true;
+ } else {
+ // rtl9300_rxCaliConf_phy_myParam
+ dac_long_cable_offset = 0;
+ eq_hold_enabled = false;
+ }
+
+ if (phy_mode == PHY_INTERFACE_MODE_1000BASEX)
+ pr_warn("%s: LEQ only valid for 10GR!\n", __func__);
+
+ pr_info("start_1.3.2");
+
+ for(i = 0; i < 10; i++) {
+ sum10 += rtl9300_sds_rxcal_leq_read(sds_num);
+ mdelay(10);
+ }
+
+ avg10 = (sum10 / 10) + (((sum10 % 10) >= 5) ? 1 : 0);
+ int10 = sum10 / 10;
+
+ pr_info("sum10:%u, avg10:%u, int10:%u", sum10, avg10, int10);
+
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER || phy_mode == PHY_INTERFACE_MODE_1000BASEX) {
+ if (dac_long_cable_offset) {
+ rtl9300_sds_rxcal_leq_offset_manual(sds_num, 1, dac_long_cable_offset);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, eq_hold_enabled);
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER)
+ rtl9300_sds_rxcal_leq_manual(sds_num, true, avg10);
+ } else {
+ if (sum10 >= 5) {
+ rtl9300_sds_rxcal_leq_offset_manual(sds_num, 1, 3);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, 0x1);
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER)
+ rtl9300_sds_rxcal_leq_manual(sds_num, true, avg10);
+ } else {
+ rtl9300_sds_rxcal_leq_offset_manual(sds_num, 1, 0);
+ rtl9300_sds_field_w(sds_num, 0x2e, 0x17, 7, 7, 0x1);
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER)
+ rtl9300_sds_rxcal_leq_manual(sds_num, true, avg10);
+ }
+ }
+ }
+
+ pr_info("Sds:%u LEQ = %u",sds_num, rtl9300_sds_rxcal_leq_read(sds_num));
+
+ pr_info("end_1.3.2");
+}
+
+void rtl9300_do_rx_calibration_3(int sds_num, phy_interface_t phy_mode)
+{
+ rtl9300_sds_rxcal_3_1(sds_num, phy_mode);
+
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER || phy_mode == PHY_INTERFACE_MODE_1000BASEX)
+ rtl9300_sds_rxcal_3_2(sds_num, phy_mode);
+}
+
+void rtl9300_do_rx_calibration_4_1(int sds_num)
+{
+ u32 vth_list[2] = {0, 0};
+ u32 tap0_list[4] = {0, 0, 0, 0};
+
+ pr_info("start_1.4.1");
+
+ // ##1.4.1
+ rtl9300_sds_rxcal_vth_manual(sds_num, false, vth_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 0, false, tap0_list);
+ mdelay(200);
+
+ pr_info("end_1.4.1");
+}
+
+void rtl9300_do_rx_calibration_4_2(u32 sds_num)
+{
+ u32 vth_list[2];
+ u32 tap_list[4];
+
+ pr_info("start_1.4.2");
+
+ rtl9300_sds_rxcal_vth_get(sds_num, vth_list);
+ rtl9300_sds_rxcal_vth_manual(sds_num, true, vth_list);
+
+ mdelay(100);
+
+ rtl9300_sds_rxcal_tap_get(sds_num, 0, tap_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 0, true, tap_list);
+
+ pr_info("end_1.4.2");
+}
+
+void rtl9300_do_rx_calibration_4(u32 sds_num)
+{
+ rtl9300_do_rx_calibration_4_1(sds_num);
+ rtl9300_do_rx_calibration_4_2(sds_num);
+}
+
+void rtl9300_do_rx_calibration_5_2(u32 sds_num)
+{
+ u32 tap1_list[4] = {0};
+ u32 tap2_list[4] = {0};
+ u32 tap3_list[4] = {0};
+ u32 tap4_list[4] = {0};
+
+ pr_info("start_1.5.2");
+
+ rtl9300_sds_rxcal_tap_manual(sds_num, 1, false, tap1_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 2, false, tap2_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 3, false, tap3_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 4, false, tap4_list);
+
+ mdelay(30);
+
+ pr_info("end_1.5.2");
+}
+
+void rtl9300_do_rx_calibration_5(u32 sds_num, phy_interface_t phy_mode)
+{
+ if (phy_mode == PHY_INTERFACE_MODE_10GBASER) // dfeTap1_4Enable true
+ rtl9300_do_rx_calibration_5_2(sds_num);
+}
+
+
+void rtl9300_do_rx_calibration_dfe_disable(u32 sds_num)
+{
+ u32 tap1_list[4] = {0};
+ u32 tap2_list[4] = {0};
+ u32 tap3_list[4] = {0};
+ u32 tap4_list[4] = {0};
+
+ rtl9300_sds_rxcal_tap_manual(sds_num, 1, true, tap1_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 2, true, tap2_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 3, true, tap3_list);
+ rtl9300_sds_rxcal_tap_manual(sds_num, 4, true, tap4_list);
+
+ mdelay(10);
+}
+
+void rtl9300_do_rx_calibration(int sds, phy_interface_t phy_mode)
+{
+ u32 latch_sts;
+
+ rtl9300_do_rx_calibration_1(sds, phy_mode);
+ rtl9300_do_rx_calibration_2(sds);
+ rtl9300_do_rx_calibration_4(sds);
+ rtl9300_do_rx_calibration_5(sds, phy_mode);
+ mdelay(20);
+
+ // Do this only for 10GR mode, SDS active in mode 0x1a
+ if (rtl9300_sds_field_r(sds, 0x1f, 9, 11, 7) == 0x1a) {
+ pr_info("%s: SDS enabled\n", __func__);
+ latch_sts = rtl9300_sds_field_r(sds, 0x4, 1, 2, 2);
+ mdelay(1);
+ latch_sts = rtl9300_sds_field_r(sds, 0x4, 1, 2, 2);
+ if (latch_sts) {
+ rtl9300_do_rx_calibration_dfe_disable(sds);
+ rtl9300_do_rx_calibration_4(sds);
+ rtl9300_do_rx_calibration_5(sds, phy_mode);
+ }
+ }
+}
+
+int rtl9300_sds_sym_err_reset(int sds_num, phy_interface_t phy_mode)
+{
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_XGMII:
+ break;
+
+ case PHY_INTERFACE_MODE_10GBASER:
+ // Read twice to clear
+ rtl930x_read_sds_phy(sds_num, 5, 1);
+ rtl930x_read_sds_phy(sds_num, 5, 1);
+ break;
+
+ case PHY_INTERFACE_MODE_1000BASEX:
+ rtl9300_sds_field_w(sds_num, 0x1, 24, 2, 0, 0);
+ rtl9300_sds_field_w(sds_num, 0x1, 3, 15, 8, 0);
+ rtl9300_sds_field_w(sds_num, 0x1, 2, 15, 0, 0);
+ break;
+
+ default:
+ pr_info("%s unsupported phy mode\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+u32 rtl9300_sds_sym_err_get(int sds_num, phy_interface_t phy_mode)
+{
+ u32 v = 0;
+
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_XGMII:
+ break;
+
+ case PHY_INTERFACE_MODE_10GBASER:
+ v = rtl930x_read_sds_phy(sds_num, 5, 1);
+ return v & 0xff;
+
+ default:
+ pr_info("%s unsupported PHY-mode\n", __func__);
+ }
+
+ return v;
+}
+
+int rtl9300_sds_check_calibration(int sds_num, phy_interface_t phy_mode)
+{
+ u32 errors1, errors2;
+
+ rtl9300_sds_sym_err_reset(sds_num, phy_mode);
+ rtl9300_sds_sym_err_reset(sds_num, phy_mode);
+
+ // Count errors during 1ms
+ errors1 = rtl9300_sds_sym_err_get(sds_num, phy_mode);
+ mdelay(1);
+ errors2 = rtl9300_sds_sym_err_get(sds_num, phy_mode);
+
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_XGMII:
+
+ if ((errors2 - errors1 > 100)
+ || (errors1 >= 0xffff00) || (errors2 >= 0xffff00)) {
+ pr_info("%s XSGMII error rate too high\n", __func__);
+ return 1;
+ }
+ break;
+ case PHY_INTERFACE_MODE_10GBASER:
+ if (errors2 > 0) {
+ pr_info("%s 10GBASER error rate too high\n", __func__);
+ return 1;
+ }
+ break;
+ default:
+ return 1;
+ }
+ return 0;
+}
+
+void rtl9300_phy_enable_10g_1g(int sds_num)
+{
+ u32 v;
+
+ // Enable 1GBit PHY
+ v = rtl930x_read_sds_phy(sds_num, PHY_PAGE_2, PHY_CTRL_REG);
+ pr_info("%s 1gbit phy: %08x\n", __func__, v);
+ v &= ~BIT(PHY_POWER_BIT);
+ rtl930x_write_sds_phy(sds_num, PHY_PAGE_2, PHY_CTRL_REG, v);
+ pr_info("%s 1gbit phy enabled: %08x\n", __func__, v);
+
+ // Enable 10GBit PHY
+ v = rtl930x_read_sds_phy(sds_num, PHY_PAGE_4, PHY_CTRL_REG);
+ pr_info("%s 10gbit phy: %08x\n", __func__, v);
+ v &= ~BIT(PHY_POWER_BIT);
+ rtl930x_write_sds_phy(sds_num, PHY_PAGE_4, PHY_CTRL_REG, v);
+ pr_info("%s 10gbit phy after: %08x\n", __func__, v);
+
+ // dal_longan_construct_mac_default_10gmedia_fiber
+ v = rtl930x_read_sds_phy(sds_num, 0x1f, 11);
+ pr_info("%s set medium: %08x\n", __func__, v);
+ v |= BIT(1);
+ rtl930x_write_sds_phy(sds_num, 0x1f, 11, v);
+ pr_info("%s set medium after: %08x\n", __func__, v);
+}
+
+#define RTL930X_MAC_FORCE_MODE_CTRL (0xCA1C)
+// phy_mode = PHY_INTERFACE_MODE_10GBASER, sds_mode = 0x1a
+int rtl9300_serdes_setup(int sds_num, phy_interface_t phy_mode)
+{
+ int sds_mode;
+ int calib_tries = 0;
+
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_HSGMII:
+ sds_mode = 0x12;
+ break;
+ case PHY_INTERFACE_MODE_1000BASEX:
+ sds_mode = 0x04;
+ break;
+ case PHY_INTERFACE_MODE_XGMII:
+ sds_mode = 0x10;
+ break;
+ case PHY_INTERFACE_MODE_10GBASER:
+ sds_mode = 0x1a;
+ break;
+ case PHY_INTERFACE_MODE_USXGMII:
+ sds_mode = 0x0d;
+ break;
+ default:
+ pr_err("%s: unknown serdes mode: %s\n", __func__, phy_modes(phy_mode));
+ return -EINVAL;
+ }
+
+ // Maybe use dal_longan_sds_init
+
+ // dal_longan_construct_serdesConfig_init // Serdes Construct
+ rtl9300_phy_enable_10g_1g(sds_num);
+
+ // Set Serdes Mode
+ rtl9300_sds_set(sds_num, 0x1a); // 0x1b: RTK_MII_10GR1000BX_AUTO
+
+ // Do RX calibration
+ do {
+ rtl9300_do_rx_calibration(sds_num, phy_mode);
+ calib_tries++;
+ mdelay(50);
+ } while (rtl9300_sds_check_calibration(sds_num, phy_mode) && calib_tries < 3);
+
+
+ return 0;
+}
+
+typedef struct {
+ u8 page;
+ u8 reg;
+ u16 data;
+} sds_config;
+
+sds_config rtl9300_a_sds_10gr_lane0[] =
+{
+ /*1G*/
+ {0x00, 0x0E, 0x3053}, {0x01, 0x14, 0x0100}, {0x21, 0x03, 0x8206},
+ {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F},
+ {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009}, {0x21, 0x0E, 0x0000},
+ {0x21, 0x0F, 0x0008}, {0x24, 0x00, 0x0668}, {0x24, 0x02, 0xD020},
+ {0x24, 0x06, 0xC000}, {0x24, 0x0B, 0x1892}, {0x24, 0x0F, 0xFFDF},
+ {0x24, 0x12, 0x03C4}, {0x24, 0x13, 0x027F}, {0x24, 0x14, 0x1311},
+ {0x24, 0x16, 0x00C9}, {0x24, 0x17, 0xA100}, {0x24, 0x1A, 0x0001},
+ {0x24, 0x1C, 0x0400}, {0x25, 0x01, 0x0300}, {0x25, 0x02, 0x1017},
+ {0x25, 0x03, 0xFFDF}, {0x25, 0x05, 0x7F7C}, {0x25, 0x07, 0x8100},
+ {0x25, 0x08, 0x0001}, {0x25, 0x09, 0xFFD4}, {0x25, 0x0A, 0x7C2F},
+ {0x25, 0x0E, 0x003F}, {0x25, 0x0F, 0x0121}, {0x25, 0x10, 0x0020},
+ {0x25, 0x11, 0x8840}, {0x2B, 0x13, 0x0050}, {0x2B, 0x18, 0x8E88},
+ {0x2B, 0x19, 0x4902}, {0x2B, 0x1D, 0x2501}, {0x2D, 0x13, 0x0050},
+ {0x2D, 0x18, 0x8E88}, {0x2D, 0x19, 0x4902}, {0x2D, 0x1D, 0x2641},
+ {0x2F, 0x13, 0x0050}, {0x2F, 0x18, 0x8E88}, {0x2F, 0x19, 0x4902},
+ {0x2F, 0x1D, 0x66E1},
+ /*3.125G*/
+ {0x28, 0x00, 0x0668}, {0x28, 0x02, 0xD020}, {0x28, 0x06, 0xC000},
+ {0x28, 0x0B, 0x1892}, {0x28, 0x0F, 0xFFDF}, {0x28, 0x12, 0x01C4},
+ {0x28, 0x13, 0x027F}, {0x28, 0x14, 0x1311}, {0x28, 0x16, 0x00C9},
+ {0x28, 0x17, 0xA100}, {0x28, 0x1A, 0x0001}, {0x28, 0x1C, 0x0400},
+ {0x29, 0x01, 0x0300}, {0x29, 0x02, 0x1017}, {0x29, 0x03, 0xFFDF},
+ {0x29, 0x05, 0x7F7C}, {0x29, 0x07, 0x8100}, {0x29, 0x08, 0x0001},
+ {0x29, 0x09, 0xFFD4}, {0x29, 0x0A, 0x7C2F}, {0x29, 0x0E, 0x003F},
+ {0x29, 0x0F, 0x0121}, {0x29, 0x10, 0x0020}, {0x29, 0x11, 0x8840},
+ /*10G*/
+ {0x06, 0x0D, 0x0F00}, {0x06, 0x00, 0x0000}, {0x06, 0x01, 0xC800},
+ {0x21, 0x03, 0x8206}, {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010},
+ {0x21, 0x07, 0xF09F}, {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009},
+ {0x21, 0x0E, 0x0000}, {0x21, 0x0F, 0x0008}, {0x2E, 0x00, 0xA668},
+ {0x2E, 0x02, 0xD020}, {0x2E, 0x06, 0xC000}, {0x2E, 0x0B, 0x1892},
+ {0x2E, 0x0F, 0xFFDF}, {0x2E, 0x11, 0x8280}, {0x2E, 0x12, 0x0044},
+ {0x2E, 0x13, 0x027F}, {0x2E, 0x14, 0x1311}, {0x2E, 0x17, 0xA100},
+ {0x2E, 0x1A, 0x0001}, {0x2E, 0x1C, 0x0400}, {0x2F, 0x01, 0x0300},
+ {0x2F, 0x02, 0x1217}, {0x2F, 0x03, 0xFFDF}, {0x2F, 0x05, 0x7F7C},
+ {0x2F, 0x07, 0x80C4}, {0x2F, 0x08, 0x0001}, {0x2F, 0x09, 0xFFD4},
+ {0x2F, 0x0A, 0x7C2F}, {0x2F, 0x0E, 0x003F}, {0x2F, 0x0F, 0x0121},
+ {0x2F, 0x10, 0x0020}, {0x2F, 0x11, 0x8840}, {0x2F, 0x14, 0xE008},
+ {0x2B, 0x13, 0x0050}, {0x2B, 0x18, 0x8E88}, {0x2B, 0x19, 0x4902},
+ {0x2B, 0x1D, 0x2501}, {0x2D, 0x13, 0x0050}, {0x2D, 0x17, 0x4109},
+ {0x2D, 0x18, 0x8E88}, {0x2D, 0x19, 0x4902}, {0x2D, 0x1C, 0x1109},
+ {0x2D, 0x1D, 0x2641}, {0x2F, 0x13, 0x0050}, {0x2F, 0x18, 0x8E88},
+ {0x2F, 0x19, 0x4902}, {0x2F, 0x1D, 0x76E1},
+};
+
+sds_config rtl9300_a_sds_10gr_lane1[] =
+{
+ /*1G*/
+ {0x00, 0x0E, 0x3053}, {0x01, 0x14, 0x0100}, {0x21, 0x03, 0x8206},
+ {0x21, 0x06, 0x0010}, {0x21, 0x07, 0xF09F}, {0x21, 0x0A, 0x0003},
+ {0x21, 0x0B, 0x0005}, {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009},
+ {0x21, 0x0E, 0x0000}, {0x21, 0x0F, 0x0008}, {0x24, 0x00, 0x0668},
+ {0x24, 0x02, 0xD020}, {0x24, 0x06, 0xC000}, {0x24, 0x0B, 0x1892},
+ {0x24, 0x0F, 0xFFDF}, {0x24, 0x12, 0x03C4}, {0x24, 0x13, 0x027F},
+ {0x24, 0x14, 0x1311}, {0x24, 0x16, 0x00C9}, {0x24, 0x17, 0xA100},
+ {0x24, 0x1A, 0x0001}, {0x24, 0x1C, 0x0400}, {0x25, 0x00, 0x820F},
+ {0x25, 0x01, 0x0300}, {0x25, 0x02, 0x1017}, {0x25, 0x03, 0xFFDF},
+ {0x25, 0x05, 0x7F7C}, {0x25, 0x07, 0x8100}, {0x25, 0x08, 0x0001},
+ {0x25, 0x09, 0xFFD4}, {0x25, 0x0A, 0x7C2F}, {0x25, 0x0E, 0x003F},
+ {0x25, 0x0F, 0x0121}, {0x25, 0x10, 0x0020}, {0x25, 0x11, 0x8840},
+ {0x2B, 0x13, 0x3D87}, {0x2B, 0x14, 0x3108}, {0x2D, 0x13, 0x3C87},
+ {0x2D, 0x14, 0x1808},
+ /*3.125G*/
+ {0x28, 0x00, 0x0668}, {0x28, 0x02, 0xD020}, {0x28, 0x06, 0xC000},
+ {0x28, 0x0B, 0x1892}, {0x28, 0x0F, 0xFFDF}, {0x28, 0x12, 0x01C4},
+ {0x28, 0x13, 0x027F}, {0x28, 0x14, 0x1311}, {0x28, 0x16, 0x00C9},
+ {0x28, 0x17, 0xA100}, {0x28, 0x1A, 0x0001}, {0x28, 0x1C, 0x0400},
+ {0x29, 0x00, 0x820F}, {0x29, 0x01, 0x0300}, {0x29, 0x02, 0x1017},
+ {0x29, 0x03, 0xFFDF}, {0x29, 0x05, 0x7F7C}, {0x29, 0x07, 0x8100},
+ {0x29, 0x08, 0x0001}, {0x29, 0x0A, 0x7C2F}, {0x29, 0x0E, 0x003F},
+ {0x29, 0x0F, 0x0121}, {0x29, 0x10, 0x0020}, {0x29, 0x11, 0x8840},
+ /*10G*/
+ {0x06, 0x0D, 0x0F00}, {0x06, 0x00, 0x0000}, {0x06, 0x01, 0xC800},
+ {0x21, 0x03, 0x8206}, {0x21, 0x05, 0x40B0}, {0x21, 0x06, 0x0010},
+ {0x21, 0x07, 0xF09F}, {0x21, 0x0A, 0x0003}, {0x21, 0x0B, 0x0005},
+ {0x21, 0x0C, 0x0007}, {0x21, 0x0D, 0x6009}, {0x21, 0x0E, 0x0000},
+ {0x21, 0x0F, 0x0008}, {0x2E, 0x00, 0xA668}, {0x2E, 0x02, 0xD020},
+ {0x2E, 0x06, 0xC000}, {0x2E, 0x0B, 0x1892}, {0x2E, 0x0F, 0xFFDF},
+ {0x2E, 0x11, 0x8280}, {0x2E, 0x12, 0x0044}, {0x2E, 0x13, 0x027F},
+ {0x2E, 0x14, 0x1311}, {0x2E, 0x17, 0xA100}, {0x2E, 0x1A, 0x0001},
+ {0x2E, 0x1C, 0x0400}, {0x2F, 0x00, 0x820F}, {0x2F, 0x01, 0x0300},
+ {0x2F, 0x02, 0x1217}, {0x2F, 0x03, 0xFFDF}, {0x2F, 0x05, 0x7F7C},
+ {0x2F, 0x07, 0x80C4}, {0x2F, 0x08, 0x0001}, {0x2F, 0x09, 0xFFD4},
+ {0x2F, 0x0A, 0x7C2F}, {0x2F, 0x0E, 0x003F}, {0x2F, 0x0F, 0x0121},
+ {0x2F, 0x10, 0x0020}, {0x2F, 0x11, 0x8840}, {0x2B, 0x13, 0x3D87},
+ {0x2B, 0x14, 0x3108}, {0x2D, 0x13, 0x3C87}, {0x2D, 0x14, 0x1808},
+};
+
+int rtl9300_sds_cmu_band_get(int sds)
+{
+ u32 page;
+ u32 en;
+ u32 cmu_band;
+
+// page = rtl9300_sds_cmu_page_get(sds);
+ page = 0x25; // 10GR and 1000BX
+ sds = (sds % 2) ? (sds - 1) : (sds);
+
+ rtl9300_sds_field_w(sds, page, 0x1c, 15, 15, 1);
+ rtl9300_sds_field_w(sds + 1, page, 0x1c, 15, 15, 1);
+
+ en = rtl9300_sds_field_r(sds, page, 27, 1, 1);
+ if(!en) { // Auto mode
+ rtl930x_write_sds_phy(sds, 0x1f, 0x02, 31);
+
+ cmu_band = rtl9300_sds_field_r(sds, 0x1f, 0x15, 5, 1);
+ } else {
+ cmu_band = rtl9300_sds_field_r(sds, page, 30, 4, 0);
+ }
+
+ return cmu_band;
+}
+
+int rtl9300_configure_serdes(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int phy_addr = phydev->mdio.addr;
+ struct device_node *dn;
+ u32 sds_num = 0;
+ int sds_mode, calib_tries = 0, phy_mode = PHY_INTERFACE_MODE_10GBASER, i;
+
+ if (dev->of_node) {
+ dn = dev->of_node;
+
+ if (of_property_read_u32(dn, "sds", &sds_num))
+ sds_num = -1;
+ pr_info("%s: Port %d, SerDes is %d\n", __func__, phy_addr, sds_num);
+ } else {
+ dev_err(dev, "No DT node.\n");
+ return -EINVAL;
+ }
+
+ if (sds_num < 0)
+ return 0;
+
+ if (phy_mode != PHY_INTERFACE_MODE_10GBASER) // TODO: for now we only patch 10GR SerDes
+ return 0;
+
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_HSGMII:
+ sds_mode = 0x12;
+ break;
+ case PHY_INTERFACE_MODE_1000BASEX:
+ sds_mode = 0x04;
+ break;
+ case PHY_INTERFACE_MODE_XGMII:
+ sds_mode = 0x10;
+ break;
+ case PHY_INTERFACE_MODE_10GBASER:
+ sds_mode = 0x1a;
+ break;
+ case PHY_INTERFACE_MODE_USXGMII:
+ sds_mode = 0x0d;
+ break;
+ default:
+ pr_err("%s: unknown serdes mode: %s\n", __func__, phy_modes(phy_mode));
+ return -EINVAL;
+ }
+
+ pr_info("%s CMU BAND is %d\n", __func__, rtl9300_sds_cmu_band_get(sds_num));
+
+ // Turn Off Serdes
+ rtl9300_sds_rst(sds_num, 0x1f);
+
+ pr_info("%s PATCHING SerDes %d\n", __func__, sds_num);
+ if (sds_num % 2) {
+ for (i = 0; i < sizeof(rtl9300_a_sds_10gr_lane1) / sizeof(sds_config); ++i) {
+ rtl930x_write_sds_phy(sds_num, rtl9300_a_sds_10gr_lane1[i].page,
+ rtl9300_a_sds_10gr_lane1[i].reg,
+ rtl9300_a_sds_10gr_lane1[i].data);
+ }
+ } else {
+ for (i = 0; i < sizeof(rtl9300_a_sds_10gr_lane0) / sizeof(sds_config); ++i) {
+ rtl930x_write_sds_phy(sds_num, rtl9300_a_sds_10gr_lane0[i].page,
+ rtl9300_a_sds_10gr_lane0[i].reg,
+ rtl9300_a_sds_10gr_lane0[i].data);
+ }
+ }
+
+ rtl9300_phy_enable_10g_1g(sds_num);
+
+ // Disable MAC
+ sw_w32_mask(0, 1, RTL930X_MAC_FORCE_MODE_CTRL);
+ mdelay(20);
+
+ // ----> dal_longan_sds_mode_set
+ pr_info("%s: Configuring RTL9300 SERDES %d, mode %02x\n", __func__, sds_num, sds_mode);
+
+ // Configure link to MAC
+ rtl9300_serdes_mac_link_config(sds_num, true, true); // MAC Construct
+
+ // Disable MAC
+ sw_w32_mask(0, 1, RTL930X_MAC_FORCE_MODE_CTRL);
+ mdelay(20);
+
+ rtl9300_force_sds_mode(sds_num, PHY_INTERFACE_MODE_NA);
+
+ // Re-Enable MAC
+ sw_w32_mask(1, 0, RTL930X_MAC_FORCE_MODE_CTRL);
+
+ rtl9300_force_sds_mode(sds_num, phy_mode);
+
+ // Do RX calibration
+ do {
+ rtl9300_do_rx_calibration(sds_num, phy_mode);
+ calib_tries++;
+ mdelay(50);
+ } while (rtl9300_sds_check_calibration(sds_num, phy_mode) && calib_tries < 3);
+
+ if (calib_tries >= 3)
+ pr_err("%s CALIBTRATION FAILED\n", __func__);
+
+ rtl9300_sds_tx_config(sds_num, phy_mode);
+
+ // The clock needs only to be configured on the FPGA implementation
+
+ return 0;
+}
+
+void rtl9310_sds_field_w(int sds, u32 page, u32 reg, int end_bit, int start_bit, u32 v)
+{
+ int l = end_bit - start_bit + 1;
+ u32 data = v;
+
+ if (l < 32) {
+ u32 mask = BIT(l) - 1;
+
+ data = rtl930x_read_sds_phy(sds, page, reg);
+ data &= ~(mask << start_bit);
+ data |= (v & mask) << start_bit;
+ }
+
+ rtl931x_write_sds_phy(sds, page, reg, data);
+}
+
+
+u32 rtl9310_sds_field_r(int sds, u32 page, u32 reg, int end_bit, int start_bit)
+{
+ int l = end_bit - start_bit + 1;
+ u32 v = rtl931x_read_sds_phy(sds, page, reg);
+
+ if (l >= 32)
+ return v;
+
+ return (v >> start_bit) & (BIT(l) - 1);
+}
+
+static void rtl931x_sds_rst(u32 sds)
+{
+ u32 o, v, o_mode;
+ int shift = ((sds & 0x3) << 3);
+
+ // TODO: We need to lock this!
+
+ o = sw_r32(RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR);
+ v = o | BIT(sds);
+ sw_w32(v, RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR);
+
+ o_mode = sw_r32(RTL931X_SERDES_MODE_CTRL + 4 * (sds >> 2));
+ v = BIT(7) | 0x1F;
+ sw_w32_mask(0xff << shift, v << shift, RTL931X_SERDES_MODE_CTRL + 4 * (sds >> 2));
+ sw_w32(o_mode, RTL931X_SERDES_MODE_CTRL + 4 * (sds >> 2));
+
+ sw_w32(o, RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR);
+}
+
+static void rtl931x_symerr_clear(u32 sds, phy_interface_t mode)
+{
+ u32 i;
+ u32 xsg_sdsid_0, xsg_sdsid_1;
+
+ switch (mode) {
+ case PHY_INTERFACE_MODE_NA:
+ break;
+ case PHY_INTERFACE_MODE_XGMII:
+ if (sds < 2)
+ xsg_sdsid_0 = sds;
+ else
+ xsg_sdsid_0 = (sds - 1) * 2;
+ xsg_sdsid_1 = xsg_sdsid_0 + 1;
+
+ for (i = 0; i < 4; ++i) {
+ rtl9310_sds_field_w(xsg_sdsid_0, 0x1, 24, 2, 0, i);
+ rtl9310_sds_field_w(xsg_sdsid_0, 0x1, 3, 15, 8, 0x0);
+ rtl9310_sds_field_w(xsg_sdsid_0, 0x1, 2, 15, 0, 0x0);
+ }
+
+ for (i = 0; i < 4; ++i) {
+ rtl9310_sds_field_w(xsg_sdsid_1, 0x1, 24, 2, 0, i);
+ rtl9310_sds_field_w(xsg_sdsid_1, 0x1, 3, 15, 8, 0x0);
+ rtl9310_sds_field_w(xsg_sdsid_1, 0x1, 2, 15, 0, 0x0);
+ }
+
+ rtl9310_sds_field_w(xsg_sdsid_0, 0x1, 0, 15, 0, 0x0);
+ rtl9310_sds_field_w(xsg_sdsid_0, 0x1, 1, 15, 8, 0x0);
+ rtl9310_sds_field_w(xsg_sdsid_1, 0x1, 0, 15, 0, 0x0);
+ rtl9310_sds_field_w(xsg_sdsid_1, 0x1, 1, 15, 8, 0x0);
+ break;
+ default:
+ break;
+ }
+
+ return;
+}
+
+static u32 rtl931x_get_analog_sds(u32 sds)
+{
+ u32 sds_map[] = { 0, 1, 2, 3, 6, 7, 10, 11, 14, 15, 18, 19, 22, 23 };
+
+ if (sds < 14)
+ return sds_map[sds];
+ return sds;
+}
+
+void rtl931x_sds_fiber_disable(u32 sds)
+{
+ u32 v = 0x3F;
+ u32 asds = rtl931x_get_analog_sds(sds);
+
+ rtl9310_sds_field_w(asds, 0x1F, 0x9, 11, 6, v);
+}
+
+static void rtl931x_sds_fiber_mode_set(u32 sds, phy_interface_t mode)
+{
+ u32 val, asds = rtl931x_get_analog_sds(sds);
+
+ /* clear symbol error count before changing mode */
+ rtl931x_symerr_clear(sds, mode);
+
+ val = 0x9F;
+ sw_w32(val, RTL931X_SERDES_MODE_CTRL + 4 * (sds >> 2));
+
+ switch (mode) {
+ case PHY_INTERFACE_MODE_SGMII:
+ val = 0x5;
+ break;
+
+ case PHY_INTERFACE_MODE_1000BASEX:
+ /* serdes mode FIBER1G */
+ val = 0x9;
+ break;
+
+ case PHY_INTERFACE_MODE_10GBASER:
+ case PHY_INTERFACE_MODE_10GKR:
+ val = 0x35;
+ break;
+/* case MII_10GR1000BX_AUTO:
+ val = 0x39;
+ break; */
+
+
+ case PHY_INTERFACE_MODE_USXGMII:
+ val = 0x1B;
+ break;
+ default:
+ val = 0x25;
+ }
+
+ pr_info("%s writing analog SerDes Mode value %02x\n", __func__, val);
+ rtl9310_sds_field_w(asds, 0x1F, 0x9, 11, 6, val);
+
+ return;
+}
+
+static int rtl931x_sds_cmu_page_get(phy_interface_t mode)
+{
+ switch (mode) {
+ case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX: // MII_1000BX_FIBER / 100BX_FIBER / 1000BX100BX_AUTO
+ return 0x24;
+ case PHY_INTERFACE_MODE_HSGMII:
+ case PHY_INTERFACE_MODE_2500BASEX: // MII_2500Base_X:
+ return 0x28;
+// case MII_HISGMII_5G:
+// return 0x2a;
+ case PHY_INTERFACE_MODE_QSGMII:
+ return 0x2a; // Code also has 0x34
+ case PHY_INTERFACE_MODE_XAUI: // MII_RXAUI_LITE:
+ return 0x2c;
+ case PHY_INTERFACE_MODE_XGMII: // MII_XSGMII
+ case PHY_INTERFACE_MODE_10GKR:
+ case PHY_INTERFACE_MODE_10GBASER: // MII_10GR
+ return 0x2e;
+ default:
+ return -1;
+ }
+ return -1;
+}
+
+static void rtl931x_cmu_type_set(u32 asds, phy_interface_t mode, int chiptype)
+{
+ int cmu_type = 0; // Clock Management Unit
+ u32 cmu_page = 0;
+ u32 frc_cmu_spd;
+ u32 evenSds;
+ u32 lane, frc_lc_mode_bitnum, frc_lc_mode_val_bitnum;
+
+ switch (mode) {
+ case PHY_INTERFACE_MODE_NA:
+ case PHY_INTERFACE_MODE_10GKR:
+ case PHY_INTERFACE_MODE_XGMII:
+ case PHY_INTERFACE_MODE_10GBASER:
+ case PHY_INTERFACE_MODE_USXGMII:
+ return;
+
+/* case MII_10GR1000BX_AUTO:
+ if (chiptype)
+ rtl9310_sds_field_w(asds, 0x24, 0xd, 14, 14, 0);
+ return; */
+
+ case PHY_INTERFACE_MODE_QSGMII:
+ cmu_type = 1;
+ frc_cmu_spd = 0;
+ break;
+
+ case PHY_INTERFACE_MODE_HSGMII:
+ cmu_type = 1;
+ frc_cmu_spd = 1;
+ break;
+
+ case PHY_INTERFACE_MODE_1000BASEX:
+ cmu_type = 1;
+ frc_cmu_spd = 0;
+ break;
+
+/* case MII_1000BX100BX_AUTO:
+ cmu_type = 1;
+ frc_cmu_spd = 0;
+ break; */
+
+ case PHY_INTERFACE_MODE_SGMII:
+ cmu_type = 1;
+ frc_cmu_spd = 0;
+ break;
+
+ case PHY_INTERFACE_MODE_2500BASEX:
+ cmu_type = 1;
+ frc_cmu_spd = 1;
+ break;
+
+ default:
+ pr_info("SerDes %d mode is invalid\n", asds);
+ return;
+ }
+
+ if (cmu_type == 1)
+ cmu_page = rtl931x_sds_cmu_page_get(mode);
+
+ lane = asds % 2;
+
+ if (!lane) {
+ frc_lc_mode_bitnum = 4;
+ frc_lc_mode_val_bitnum = 5;
+ } else {
+ frc_lc_mode_bitnum = 6;
+ frc_lc_mode_val_bitnum = 7;
+ }
+
+ evenSds = asds - lane;
+
+ pr_info("%s: cmu_type %0d cmu_page %x frc_cmu_spd %d lane %d asds %d\n",
+ __func__, cmu_type, cmu_page, frc_cmu_spd, lane, asds);
+
+ if (cmu_type == 1) {
+ pr_info("%s A CMU page 0x28 0x7 %08x\n", __func__, rtl931x_read_sds_phy(asds, 0x28, 0x7));
+ rtl9310_sds_field_w(asds, cmu_page, 0x7, 15, 15, 0);
+ pr_info("%s B CMU page 0x28 0x7 %08x\n", __func__, rtl931x_read_sds_phy(asds, 0x28, 0x7));
+ if (chiptype) {
+ rtl9310_sds_field_w(asds, cmu_page, 0xd, 14, 14, 0);
+ }
+
+ rtl9310_sds_field_w(evenSds, 0x20, 0x12, 3, 2, 0x3);
+ rtl9310_sds_field_w(evenSds, 0x20, 0x12, frc_lc_mode_bitnum, frc_lc_mode_bitnum, 1);
+ rtl9310_sds_field_w(evenSds, 0x20, 0x12, frc_lc_mode_val_bitnum, frc_lc_mode_val_bitnum, 0);
+ rtl9310_sds_field_w(evenSds, 0x20, 0x12, 12, 12, 1);
+ rtl9310_sds_field_w(evenSds, 0x20, 0x12, 15, 13, frc_cmu_spd);
+ }
+
+ pr_info("%s CMU page 0x28 0x7 %08x\n", __func__, rtl931x_read_sds_phy(asds, 0x28, 0x7));
+ return;
+}
+
+static void rtl931x_sds_rx_rst(u32 sds)
+{
+ u32 asds = rtl931x_get_analog_sds(sds);
+
+ if (sds < 2)
+ return;
+
+ rtl931x_write_sds_phy(asds, 0x2e, 0x12, 0x2740);
+ rtl931x_write_sds_phy(asds, 0x2f, 0x0, 0x0);
+ rtl931x_write_sds_phy(asds, 0x2f, 0x2, 0x2010);
+ rtl931x_write_sds_phy(asds, 0x20, 0x0, 0xc10);
+
+ rtl931x_write_sds_phy(asds, 0x2e, 0x12, 0x27c0);
+ rtl931x_write_sds_phy(asds, 0x2f, 0x0, 0xc000);
+ rtl931x_write_sds_phy(asds, 0x2f, 0x2, 0x6010);
+ rtl931x_write_sds_phy(asds, 0x20, 0x0, 0xc30);
+
+ mdelay(50);
+}
+
+static void rtl931x_sds_disable(u32 sds)
+{
+ u32 v = 0x1f;
+
+ v |= BIT(7);
+ sw_w32(v, RTL931X_SERDES_MODE_CTRL + (sds >> 2) * 4);
+}
+
+static void rtl931x_sds_mii_mode_set(u32 sds, phy_interface_t mode)
+{
+ u32 val;
+
+ switch (mode) {
+ case PHY_INTERFACE_MODE_QSGMII:
+ val = 0x6;
+ break;
+ case PHY_INTERFACE_MODE_XGMII:
+ val = 0x10; // serdes mode XSGMII
+ break;
+ case PHY_INTERFACE_MODE_USXGMII:
+ case PHY_INTERFACE_MODE_2500BASEX:
+ val = 0xD;
+ break;
+ case PHY_INTERFACE_MODE_HSGMII:
+ val = 0x12;
+ break;
+ case PHY_INTERFACE_MODE_SGMII:
+ val = 0x2;
+ break;
+ default:
+ return;
+ }
+
+ val |= (1 << 7);
+
+ sw_w32(val, RTL931X_SERDES_MODE_CTRL + 4 * (sds >> 2));
+}
+
+static sds_config sds_config_10p3125g_type1[] = {
+ { 0x2E, 0x00, 0x0107 }, { 0x2E, 0x01, 0x01A3 }, { 0x2E, 0x02, 0x6A24 },
+ { 0x2E, 0x03, 0xD10D }, { 0x2E, 0x04, 0x8000 }, { 0x2E, 0x05, 0xA17E },
+ { 0x2E, 0x06, 0xE31D }, { 0x2E, 0x07, 0x800E }, { 0x2E, 0x08, 0x0294 },
+ { 0x2E, 0x09, 0x0CE4 }, { 0x2E, 0x0A, 0x7FC8 }, { 0x2E, 0x0B, 0xE0E7 },
+ { 0x2E, 0x0C, 0x0200 }, { 0x2E, 0x0D, 0xDF80 }, { 0x2E, 0x0E, 0x0000 },
+ { 0x2E, 0x0F, 0x1FC2 }, { 0x2E, 0x10, 0x0C3F }, { 0x2E, 0x11, 0x0000 },
+ { 0x2E, 0x12, 0x27C0 }, { 0x2E, 0x13, 0x7E1D }, { 0x2E, 0x14, 0x1300 },
+ { 0x2E, 0x15, 0x003F }, { 0x2E, 0x16, 0xBE7F }, { 0x2E, 0x17, 0x0090 },
+ { 0x2E, 0x18, 0x0000 }, { 0x2E, 0x19, 0x4000 }, { 0x2E, 0x1A, 0x0000 },
+ { 0x2E, 0x1B, 0x8000 }, { 0x2E, 0x1C, 0x011F }, { 0x2E, 0x1D, 0x0000 },
+ { 0x2E, 0x1E, 0xC8FF }, { 0x2E, 0x1F, 0x0000 }, { 0x2F, 0x00, 0xC000 },
+ { 0x2F, 0x01, 0xF000 }, { 0x2F, 0x02, 0x6010 }, { 0x2F, 0x12, 0x0EE7 },
+ { 0x2F, 0x13, 0x0000 }
+};
+
+static sds_config sds_config_10p3125g_cmu_type1[] = {
+ { 0x2F, 0x03, 0x4210 }, { 0x2F, 0x04, 0x0000 }, { 0x2F, 0x05, 0x0019 },
+ { 0x2F, 0x06, 0x18A6 }, { 0x2F, 0x07, 0x2990 }, { 0x2F, 0x08, 0xFFF4 },
+ { 0x2F, 0x09, 0x1F08 }, { 0x2F, 0x0A, 0x0000 }, { 0x2F, 0x0B, 0x8000 },
+ { 0x2F, 0x0C, 0x4224 }, { 0x2F, 0x0D, 0x0000 }, { 0x2F, 0x0E, 0x0000 },
+ { 0x2F, 0x0F, 0xA470 }, { 0x2F, 0x10, 0x8000 }, { 0x2F, 0x11, 0x037B }
+};
+
+void rtl931x_sds_init(u32 sds, phy_interface_t mode)
+{
+
+ u32 board_sds_tx_type1[] = { 0x1C3, 0x1C3, 0x1C3, 0x1A3, 0x1A3,
+ 0x1A3, 0x143, 0x143, 0x143, 0x143, 0x163, 0x163
+ };
+
+ u32 board_sds_tx[] = { 0x1A00, 0x1A00, 0x200, 0x200, 0x200,
+ 0x200, 0x1A3, 0x1A3, 0x1A3, 0x1A3, 0x1E3, 0x1E3
+ };
+
+ u32 board_sds_tx2[] = { 0xDC0, 0x1C0, 0x200, 0x180, 0x160,
+ 0x123, 0x123, 0x163, 0x1A3, 0x1A0, 0x1C3, 0x9C3
+ };
+
+ u32 asds, dSds, ori, model_info, val;
+ int chiptype = 0;
+
+ asds = rtl931x_get_analog_sds(sds);
+
+ if (sds > 13)
+ return;
+
+ pr_info("%s: set sds %d to mode %d\n", __func__, sds, mode);
+ val = rtl9310_sds_field_r(asds, 0x1F, 0x9, 11, 6);
+
+ pr_info("%s: fibermode %08X stored mode 0x%x analog SDS %d", __func__,
+ rtl931x_read_sds_phy(asds, 0x1f, 0x9), val, asds);
+ pr_info("%s: SGMII mode %08X in 0x24 0x9 analog SDS %d", __func__,
+ rtl931x_read_sds_phy(asds, 0x24, 0x9), asds);
+ pr_info("%s: CMU mode %08X stored even SDS %d", __func__,
+ rtl931x_read_sds_phy(asds & ~1, 0x20, 0x12), asds & ~1);
+ pr_info("%s: serdes_mode_ctrl %08X", __func__, RTL931X_SERDES_MODE_CTRL + 4 * (sds >> 2));
+ pr_info("%s CMU page 0x24 0x7 %08x\n", __func__, rtl931x_read_sds_phy(asds, 0x24, 0x7));
+ pr_info("%s CMU page 0x26 0x7 %08x\n", __func__, rtl931x_read_sds_phy(asds, 0x26, 0x7));
+ pr_info("%s CMU page 0x28 0x7 %08x\n", __func__, rtl931x_read_sds_phy(asds, 0x28, 0x7));
+ pr_info("%s XSG page 0x0 0xe %08x\n", __func__, rtl931x_read_sds_phy(dSds, 0x0, 0xe));
+ pr_info("%s XSG2 page 0x0 0xe %08x\n", __func__, rtl931x_read_sds_phy(dSds + 1, 0x0, 0xe));
+
+ model_info = sw_r32(RTL93XX_MODEL_NAME_INFO);
+ if ((model_info >> 4) & 0x1) {
+ pr_info("detected chiptype 1\n");
+ chiptype = 1;
+ } else {
+ pr_info("detected chiptype 0\n");
+ }
+
+ if (sds < 2)
+ dSds = sds;
+ else
+ dSds = (sds - 1) * 2;
+
+ pr_info("%s: 2.5gbit %08X dsds %d", __func__,
+ rtl931x_read_sds_phy(dSds, 0x1, 0x14), dSds);
+
+ pr_info("%s: RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR 0x%08X\n", __func__, sw_r32(RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR));
+ ori = sw_r32(RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR);
+ val = ori | (1 << sds);
+ sw_w32(val, RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR);
+
+ switch (mode) {
+ case PHY_INTERFACE_MODE_NA:
+ break;
+
+ case PHY_INTERFACE_MODE_XGMII: // MII_XSGMII
+
+ if (chiptype) {
+ u32 xsg_sdsid_1;
+ xsg_sdsid_1 = dSds + 1;
+ //fifo inv clk
+ rtl9310_sds_field_w(dSds, 0x1, 0x1, 7, 4, 0xf);
+ rtl9310_sds_field_w(dSds, 0x1, 0x1, 3, 0, 0xf);
+
+ rtl9310_sds_field_w(xsg_sdsid_1, 0x1, 0x1, 7, 4, 0xf);
+ rtl9310_sds_field_w(xsg_sdsid_1, 0x1, 0x1, 3, 0, 0xf);
+
+ }
+
+ rtl9310_sds_field_w(dSds, 0x0, 0xE, 12, 12, 1);
+ rtl9310_sds_field_w(dSds + 1, 0x0, 0xE, 12, 12, 1);
+ break;
+
+ case PHY_INTERFACE_MODE_USXGMII: // MII_USXGMII_10GSXGMII/10GDXGMII/10GQXGMII:
+ u32 i, evenSds;
+ u32 op_code = 0x6003;
+
+ if (chiptype) {
+ rtl9310_sds_field_w(asds, 0x6, 0x2, 12, 12, 1);
+
+ for (i = 0; i < sizeof(sds_config_10p3125g_type1) / sizeof(sds_config); ++i) {
+ rtl931x_write_sds_phy(asds, sds_config_10p3125g_type1[i].page - 0x4, sds_config_10p3125g_type1[i].reg, sds_config_10p3125g_type1[i].data);
+ }
+
+ evenSds = asds - (asds % 2);
+
+ for (i = 0; i < sizeof(sds_config_10p3125g_cmu_type1) / sizeof(sds_config); ++i) {
+ rtl931x_write_sds_phy(evenSds,
+ sds_config_10p3125g_cmu_type1[i].page - 0x4, sds_config_10p3125g_cmu_type1[i].reg, sds_config_10p3125g_cmu_type1[i].data);
+ }
+
+ rtl9310_sds_field_w(asds, 0x6, 0x2, 12, 12, 0);
+ } else {
+
+ rtl9310_sds_field_w(asds, 0x2e, 0xd, 6, 0, 0x0);
+ rtl9310_sds_field_w(asds, 0x2e, 0xd, 7, 7, 0x1);
+
+ rtl9310_sds_field_w(asds, 0x2e, 0x1c, 5, 0, 0x1E);
+ rtl9310_sds_field_w(asds, 0x2e, 0x1d, 11, 0, 0x00);
+ rtl9310_sds_field_w(asds, 0x2e, 0x1f, 11, 0, 0x00);
+ rtl9310_sds_field_w(asds, 0x2f, 0x0, 11, 0, 0x00);
+ rtl9310_sds_field_w(asds, 0x2f, 0x1, 11, 0, 0x00);
+
+ rtl9310_sds_field_w(asds, 0x2e, 0xf, 12, 6, 0x7F);
+ rtl931x_write_sds_phy(asds, 0x2f, 0x12, 0xaaa);
+
+ rtl931x_sds_rx_rst(sds);
+
+ rtl931x_write_sds_phy(asds, 0x7, 0x10, op_code);
+ rtl931x_write_sds_phy(asds, 0x6, 0x1d, 0x0480);
+ rtl931x_write_sds_phy(asds, 0x6, 0xe, 0x0400);
+ }
+ break;
+
+ case PHY_INTERFACE_MODE_10GBASER: // MII_10GR / MII_10GR1000BX_AUTO:
+ // configure 10GR fiber mode=1
+ rtl9310_sds_field_w(asds, 0x1f, 0xb, 1, 1, 1);
+
+ // init fiber_1g
+ rtl9310_sds_field_w(dSds, 0x3, 0x13, 15, 14, 0);
+
+ rtl9310_sds_field_w(dSds, 0x2, 0x0, 12, 12, 1);
+ rtl9310_sds_field_w(dSds, 0x2, 0x0, 6, 6, 1);
+ rtl9310_sds_field_w(dSds, 0x2, 0x0, 13, 13, 0);
+
+ // init auto
+ rtl9310_sds_field_w(asds, 0x1f, 13, 15, 0, 0x109e);
+ rtl9310_sds_field_w(asds, 0x1f, 0x6, 14, 10, 0x8);
+ rtl9310_sds_field_w(asds, 0x1f, 0x7, 10, 4, 0x7f);
+ break;
+
+ case PHY_INTERFACE_MODE_HSGMII:
+ rtl9310_sds_field_w(dSds, 0x1, 0x14, 8, 8, 1);
+ break;
+
+ case PHY_INTERFACE_MODE_1000BASEX: // MII_1000BX_FIBER
+ rtl9310_sds_field_w(dSds, 0x3, 0x13, 15, 14, 0);
+
+ rtl9310_sds_field_w(dSds, 0x2, 0x0, 12, 12, 1);
+ rtl9310_sds_field_w(dSds, 0x2, 0x0, 6, 6, 1);
+ rtl9310_sds_field_w(dSds, 0x2, 0x0, 13, 13, 0);
+ break;
+
+ case PHY_INTERFACE_MODE_SGMII:
+ rtl9310_sds_field_w(asds, 0x24, 0x9, 15, 15, 0);
+ break;
+
+ case PHY_INTERFACE_MODE_2500BASEX:
+ rtl9310_sds_field_w(dSds, 0x1, 0x14, 8, 8, 1);
+ break;
+
+ case PHY_INTERFACE_MODE_QSGMII:
+ default:
+ pr_info("%s: PHY mode %s not supported by SerDes %d\n",
+ __func__, phy_modes(mode), sds);
+ return;
+ }
+
+ rtl931x_cmu_type_set(asds, mode, chiptype);
+
+ if (sds >= 2 && sds <= 13) {
+ if (chiptype)
+ rtl931x_write_sds_phy(asds, 0x2E, 0x1, board_sds_tx_type1[sds - 2]);
+ else {
+ val = 0xa0000;
+ sw_w32(val, RTL931X_CHIP_INFO_ADDR);
+ val = sw_r32(RTL931X_CHIP_INFO_ADDR);
+ if (val & BIT(28)) // consider 9311 etc. RTL9313_CHIP_ID == HWP_CHIP_ID(unit))
+ {
+ rtl931x_write_sds_phy(asds, 0x2E, 0x1, board_sds_tx2[sds - 2]);
+ } else {
+ rtl931x_write_sds_phy(asds, 0x2E, 0x1, board_sds_tx[sds - 2]);
+ }
+ val = 0;
+ sw_w32(val, RTL931X_CHIP_INFO_ADDR);
+ }
+ }
+
+ val = ori & ~BIT(sds);
+ sw_w32(val, RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR);
+ pr_debug("%s: RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR 0x%08X\n", __func__, sw_r32(RTL931X_PS_SERDES_OFF_MODE_CTRL_ADDR));
+
+ if (mode == PHY_INTERFACE_MODE_XGMII || mode == PHY_INTERFACE_MODE_QSGMII
+ || mode == PHY_INTERFACE_MODE_HSGMII || mode == PHY_INTERFACE_MODE_SGMII
+ || mode == PHY_INTERFACE_MODE_USXGMII) {
+ if (mode == PHY_INTERFACE_MODE_XGMII)
+ rtl931x_sds_mii_mode_set(sds, mode);
+ else
+ rtl931x_sds_fiber_mode_set(sds, mode);
+ }
+}
+
+int rtl931x_sds_cmu_band_set(int sds, bool enable, u32 band, phy_interface_t mode)
+{
+ u32 asds;
+ int page = rtl931x_sds_cmu_page_get(mode);
+
+ sds -= (sds % 2);
+ sds = sds & ~1;
+ asds = rtl931x_get_analog_sds(sds);
+ page += 1;
+
+ if (enable) {
+ rtl9310_sds_field_w(asds, page, 0x7, 13, 13, 0);
+ rtl9310_sds_field_w(asds, page, 0x7, 11, 11, 0);
+ } else {
+ rtl9310_sds_field_w(asds, page, 0x7, 13, 13, 0);
+ rtl9310_sds_field_w(asds, page, 0x7, 11, 11, 0);
+ }
+
+ rtl9310_sds_field_w(asds, page, 0x7, 4, 0, band);
+
+ rtl931x_sds_rst(sds);
+
+ return 0;
+}
+
+int rtl931x_sds_cmu_band_get(int sds, phy_interface_t mode)
+{
+ int page = rtl931x_sds_cmu_page_get(mode);
+ u32 asds, band;
+
+ sds -= (sds % 2);
+ asds = rtl931x_get_analog_sds(sds);
+ page += 1;
+ rtl931x_write_sds_phy(asds, 0x1f, 0x02, 73);
+
+ rtl9310_sds_field_w(asds, page, 0x5, 15, 15, 1);
+ band = rtl9310_sds_field_r(asds, 0x1f, 0x15, 8, 3);
+ pr_info("%s band is: %d\n", __func__, band);
+
+ return band;
+}
+
+
+int rtl931x_link_sts_get(u32 sds)
+{
+ u32 sts, sts1, latch_sts, latch_sts1;
+ if (0){
+ u32 xsg_sdsid_0, xsg_sdsid_1;
+
+ xsg_sdsid_0 = sds < 2 ? sds : (sds - 1) * 2;
+ xsg_sdsid_1 = xsg_sdsid_0 + 1;
+
+ sts = rtl9310_sds_field_r(xsg_sdsid_0, 0x1, 29, 8, 0);
+ sts1 = rtl9310_sds_field_r(xsg_sdsid_1, 0x1, 29, 8, 0);
+ latch_sts = rtl9310_sds_field_r(xsg_sdsid_0, 0x1, 30, 8, 0);
+ latch_sts1 = rtl9310_sds_field_r(xsg_sdsid_1, 0x1, 30, 8, 0);
+ } else {
+ u32 asds, dsds;
+
+ asds = rtl931x_get_analog_sds(sds);
+ sts = rtl9310_sds_field_r(asds, 0x5, 0, 12, 12);
+ latch_sts = rtl9310_sds_field_r(asds, 0x4, 1, 2, 2);
+
+ dsds = sds < 2 ? sds : (sds - 1) * 2;
+ latch_sts1 = rtl9310_sds_field_r(dsds, 0x2, 1, 2, 2);
+ sts1 = rtl9310_sds_field_r(dsds, 0x2, 1, 2, 2);
+ }
+
+ pr_info("%s: serdes %d sts %d, sts1 %d, latch_sts %d, latch_sts1 %d\n", __func__,
+ sds, sts, sts1, latch_sts, latch_sts1);
+ return sts1;
+}
+
+static int rtl8214fc_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+{
+ struct phy_device *phydev = upstream;
+
+ rtl8214fc_media_set(phydev, true);
+
+ return 0;
+}
+
+static void rtl8214fc_sfp_remove(void *upstream)
+{
+ struct phy_device *phydev = upstream;
+
+ rtl8214fc_media_set(phydev, false);
+}
+
+static const struct sfp_upstream_ops rtl8214fc_sfp_ops = {
+ .attach = phy_sfp_attach,
+ .detach = phy_sfp_detach,
+ .module_insert = rtl8214fc_sfp_insert,
+ .module_remove = rtl8214fc_sfp_remove,
+};
+
+static int rtl8214fc_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int addr = phydev->mdio.addr;
+ int ret = 0;
+
+ /* 839x has internal SerDes */
+ if (soc_info.id == 0x8393)
return -ENODEV;
- if (addr < 24)
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ devm_phy_package_join(dev, phydev, addr & (~7),
+ sizeof(struct rtl83xx_shared_private));
+
+ if (!(addr % 8)) {
+ struct rtl83xx_shared_private *shared = phydev->shared->priv;
+ shared->name = "RTL8214FC";
+ /* Configuration must be done while patching still possible */
+ ret = rtl8380_configure_rtl8214fc(phydev);
+ if (ret)
+ return ret;
+ }
+
+ return phy_sfp_probe(phydev, &rtl8214fc_sfp_ops);
+}
+
+static int rtl8214c_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int addr = phydev->mdio.addr;
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ devm_phy_package_join(dev, phydev, addr & (~7),
+ sizeof(struct rtl83xx_shared_private));
+
+ if (!(addr % 8)) {
+ struct rtl83xx_shared_private *shared = phydev->shared->priv;
+ shared->name = "RTL8214C";
+ /* Configuration must be done whil patching still possible */
+ return rtl8380_configure_rtl8214c(phydev);
+ }
+ return 0;
+}
+
+static int rtl8218b_ext_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int addr = phydev->mdio.addr;
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ devm_phy_package_join(dev, phydev, addr & (~7),
+ sizeof(struct rtl83xx_shared_private));
+
+ if (!(addr % 8)) {
+ struct rtl83xx_shared_private *shared = phydev->shared->priv;
+ shared->name = "RTL8218B (external)";
+ if (soc_info.family == RTL8380_FAMILY_ID) {
+ /* Configuration must be done while patching still possible */
+ return rtl8380_configure_ext_rtl8218b(phydev);
+ }
+ }
+
+ return 0;
+}
+
+static int rtl8218b_int_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int addr = phydev->mdio.addr;
+
+ if (soc_info.family != RTL8380_FAMILY_ID)
+ return -ENODEV;
+ if (addr >= 24)
return -ENODEV;
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ pr_debug("%s: id: %d\n", __func__, addr);
+ /* All base addresses of the PHYs start at multiples of 8 */
+ devm_phy_package_join(dev, phydev, addr & (~7),
+ sizeof(struct rtl83xx_shared_private));
+
+ if (!(addr % 8)) {
+ struct rtl83xx_shared_private *shared = phydev->shared->priv;
+ shared->name = "RTL8218B (internal)";
+ /* Configuration must be done while patching still possible */
+ return rtl8380_configure_int_rtl8218b(phydev);
+ }
+
+ return 0;
+}
+
+static int rtl8218d_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int addr = phydev->mdio.addr;
+
+ pr_debug("%s: id: %d\n", __func__, addr);
+ /* All base addresses of the PHYs start at multiples of 8 */
+ devm_phy_package_join(dev, phydev, addr & (~7),
+ sizeof(struct rtl83xx_shared_private));
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ if (!(addr % 8)) {
+ struct rtl83xx_shared_private *shared = phydev->shared->priv;
+ shared->name = "RTL8218D";
+ /* Configuration must be done while patching still possible */
+// TODO: return configure_rtl8218d(phydev);
+ }
+ return 0;
+}
+
+static int rtl838x_serdes_probe(struct phy_device *phydev)
+{
+ int addr = phydev->mdio.addr;
- priv->name = "RTL8380 Serdes";
+ if (soc_info.family != RTL8380_FAMILY_ID)
+ return -ENODEV;
+ if (addr < 24)
+ return -ENODEV;
/* On the RTL8380M, PHYs 24-27 connect to the internal SerDes */
if (soc_info.id == 0x8380) {
static int rtl8393_serdes_probe(struct phy_device *phydev)
{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
int addr = phydev->mdio.addr;
pr_info("%s: id: %d\n", __func__, addr);
if (addr < 24)
return -ENODEV;
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
-
- priv->name = "RTL8393 Serdes";
return rtl8390_configure_serdes(phydev);
}
static int rtl8390_serdes_probe(struct phy_device *phydev)
{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
int addr = phydev->mdio.addr;
if (soc_info.family != RTL8390_FAMILY_ID)
if (addr < 24)
return -ENODEV;
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
-
- priv->name = "RTL8390 Serdes";
return rtl8390_configure_generic(phydev);
}
static int rtl9300_serdes_probe(struct phy_device *phydev)
{
- struct device *dev = &phydev->mdio.dev;
- struct rtl838x_phy_priv *priv;
- int addr = phydev->mdio.addr;
-
if (soc_info.family != RTL9300_FAMILY_ID)
return -ENODEV;
- if (addr < 24)
- return -ENODEV;
-
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ phydev_info(phydev, "Detected internal RTL9300 Serdes\n");
- priv->name = "RTL9300 Serdes";
return rtl9300_configure_serdes(phydev);
}
PHY_ID_MATCH_MODEL(PHY_ID_RTL8214C),
.name = "Realtek RTL8214C",
.features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.match_phy_device = rtl8214c_match_phy_device,
.probe = rtl8214c_phy_probe,
.suspend = genphy_suspend,
PHY_ID_MATCH_MODEL(PHY_ID_RTL8214FC),
.name = "Realtek RTL8214FC",
.features = PHY_GBIT_FIBRE_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.match_phy_device = rtl8214fc_match_phy_device,
.probe = rtl8214fc_phy_probe,
- .suspend = genphy_suspend,
- .resume = genphy_resume,
+ .suspend = rtl8214fc_suspend,
+ .resume = rtl8214fc_resume,
.set_loopback = genphy_loopback,
- .read_mmd = rtl8218b_read_mmd,
- .write_mmd = rtl8218b_write_mmd,
.set_port = rtl8214fc_set_port,
.get_port = rtl8214fc_get_port,
.set_eee = rtl8214fc_set_eee,
PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_E),
.name = "Realtek RTL8218B (external)",
.features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.match_phy_device = rtl8218b_ext_match_phy_device,
.probe = rtl8218b_ext_phy_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
.set_loopback = genphy_loopback,
- .read_mmd = rtl8218b_read_mmd,
- .write_mmd = rtl8218b_write_mmd,
.set_eee = rtl8218b_set_eee,
.get_eee = rtl8218b_get_eee,
},
PHY_ID_MATCH_MODEL(PHY_ID_RTL8218D),
.name = "REALTEK RTL8218D",
.features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.probe = rtl8218d_phy_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
.set_eee = rtl8218d_set_eee,
.get_eee = rtl8218d_get_eee,
},
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8221B),
+ .name = "REALTEK RTL8221B",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ .read_page = rtl8226_read_page,
+ .write_page = rtl8226_write_page,
+ .read_status = rtl8226_read_status,
+ .config_aneg = rtl8226_config_aneg,
+ .set_eee = rtl8226_set_eee,
+ .get_eee = rtl8226_get_eee,
+ },
{
PHY_ID_MATCH_MODEL(PHY_ID_RTL8226),
.name = "REALTEK RTL8226",
.features = PHY_GBIT_FEATURES,
- .probe = rtl8226_phy_probe,
+ .flags = PHY_HAS_REALTEK_PAGES,
.suspend = genphy_suspend,
.resume = genphy_resume,
.set_loopback = genphy_loopback,
- .read_mmd = rtl8226_read_mmd,
- .write_mmd = rtl8226_write_mmd,
.read_page = rtl8226_read_page,
.write_page = rtl8226_write_page,
.read_status = rtl8226_read_status,
PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_I),
.name = "Realtek RTL8218B (internal)",
.features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.probe = rtl8218b_int_phy_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
.set_loopback = genphy_loopback,
- .read_mmd = rtl8218b_read_mmd,
- .write_mmd = rtl8218b_write_mmd,
.set_eee = rtl8218b_set_eee,
.get_eee = rtl8218b_get_eee,
},
PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_I),
.name = "Realtek RTL8380 SERDES",
.features = PHY_GBIT_FIBRE_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.probe = rtl838x_serdes_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
.set_loopback = genphy_loopback,
- .read_mmd = rtl8218b_read_mmd,
- .write_mmd = rtl8218b_write_mmd,
.read_status = rtl8380_read_status,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_RTL8393_I),
.name = "Realtek RTL8393 SERDES",
.features = PHY_GBIT_FIBRE_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.probe = rtl8393_serdes_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
PHY_ID_MATCH_MODEL(PHY_ID_RTL8390_GENERIC),
.name = "Realtek RTL8390 Generic",
.features = PHY_GBIT_FIBRE_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.probe = rtl8390_serdes_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
PHY_ID_MATCH_MODEL(PHY_ID_RTL9300_I),
.name = "REALTEK RTL9300 SERDES",
.features = PHY_GBIT_FIBRE_FEATURES,
+ .flags = PHY_HAS_REALTEK_PAGES,
.probe = rtl9300_serdes_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
.set_loopback = genphy_loopback,
+ .read_status = rtl9300_read_status,
},
};
projects / openwrt / staging / wigyori.git / blobdiff