- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio16", "gpio54", "gpio24", "gpio25";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14",
- "gpio15", "gpio55", "gpio56", "gpio57", "gpio58",
- "gpio64", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb_pwr_en_pins: usb_pwr_en_pins {
- mux {
- pins = "gpio22";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "ok";
-
- spi4: spi@1a280000 {
- status = "ok";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash: m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- MIBIB@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- SBL2@40000 {
- label = "SBL2";
- reg = <0x40000 0x40000>;
- read-only;
- };
-
- SBL3@80000 {
- label = "SBL3";
- reg = <0x80000 0x80000>;
- read-only;
- };
-
- DDRCONFIG@100000 {
- label = "DDRCONFIG";
- reg = <0x100000 0x10000>;
- read-only;
- };
-
- SSD@110000 {
- label = "SSD";
- reg = <0x110000 0x10000>;
- read-only;
- };
-
- TZ@120000 {
- label = "TZ";
- reg = <0x120000 0x80000>;
- read-only;
- };
-
- RPM@1a0000 {
- label = "RPM";
- reg = <0x1a0000 0x80000>;
- read-only;
- };
-
- APPSBL@220000 {
- label = "APPSBL";
- reg = <0x220000 0x80000>;
- read-only;
- };
-
- APPSBLENV@2a0000 {
- label = "APPSBLENV";
- reg = <0x2a0000 0x10000>;
- };
-
- PRODUCTDATA: PRODUCTDATA@2b0000 {
- label = "PRODUCTDATA";
- reg = <0x2b0000 0x30000>;
- read-only;
- };
-
- ART@2e0000 {
- label = "ART";
- reg = <0x2e0000 0x40000>;
- read-only;
- };
-
- TP@320000 {
- label = "TP";
- reg = <0x320000 0x40000>;
- read-only;
- };
-
- TINY@360000 {
- label = "TINY";
- reg = <0x360000 0x500000>;
- read-only;
- };
-
- firmware@860000 {
- label = "firmware";
- reg = <0x860000 0x17a0000>;
- };
- };
- };
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
-
- pinctrl-0 = <&usb_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb30@1 {
- status = "ok";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- force_gen1 = <1>;
- };
-