Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready
This ethernet router is based on the same platform as the hEX PoE lite.
Installation
1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
* DHCP-Option 66 (TFTP server name) pointing to a local TFTP
Server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
* rbcfg set boot_protocol bootp
* rbcfg set boot_device ethnand
* rbcfg apply
Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall
Signed-off-by: Robert Marko <robimarko@gmail.com>
ucidef_set_led_switch "port5" "port5" "rb750:green:port5" "switch0" "0x02"
;;
rb-750-r2|\
ucidef_set_led_switch "port5" "port5" "rb750:green:port5" "switch0" "0x02"
;;
rb-750-r2|\
rb-750up-r2)
ucidef_set_led_timer "user" "USER" "rb:green:user" "1000" "1000"
ucidef_set_led_netdev "port1" "port1" "rb:green:port1" "eth0"
rb-750up-r2)
ucidef_set_led_timer "user" "USER" "rb:green:user" "1000" "1000"
ucidef_set_led_netdev "port1" "port1" "rb:green:port1" "eth0"
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
rb-750-r2|\
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
rb-750-r2|\
rb-750up-r2)
ucidef_set_interfaces_lan_wan "eth1.1" "eth0"
ucidef_add_switch "switch0" \
rb-750up-r2)
ucidef_set_interfaces_lan_wan "eth1.1" "eth0"
ucidef_add_switch "switch0" \
ucidef_add_gpio_switch "usb_power_switch" "USB Power Switch" "45" "1"
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "14"
;;
ucidef_add_gpio_switch "usb_power_switch" "USB Power Switch" "45" "1"
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "14"
;;
+rb-750p-pbr2)
+ ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "14"
+ ;;
status_led="rb750:green:act"
;;
rb-750-r2|\
status_led="rb750:green:act"
;;
rb-750-r2|\
rb-750up-r2|\
rb-911g-2hpnd|\
rb-911g-5hpacd|\
rb-750up-r2|\
rb-911g-2hpnd|\
rb-911g-5hpacd|\
*"RouterBOARD 750GL")
name="rb-750gl"
;;
*"RouterBOARD 750GL")
name="rb-750gl"
;;
+ *"RouterBOARD 750P r2")
+ name="rb-750p-pbr2"
+ ;;
*"RouterBOARD 750UP r2")
name="rb-750up-r2"
;;
*"RouterBOARD 750UP r2")
name="rb-750up-r2"
;;
# these boards use metadata images
fritz300e|\
rb-750-r2|\
# these boards use metadata images
fritz300e|\
rb-750-r2|\
rb-750up-r2|\
rb-941-2nd|\
rb-951ui-2nd|\
rb-750up-r2|\
rb-941-2nd|\
rb-951ui-2nd|\
nand_do_upgrade "$1"
;;
rb-750-r2|\
nand_do_upgrade "$1"
;;
rb-750-r2|\
rb-750up-r2|\
rb-941-2nd|\
rb-951ui-2nd|\
rb-750up-r2|\
rb-941-2nd|\
rb-951ui-2nd|\
MikroTik RouterBOARD hAP ac lite
MikroTik RouterBOARD hEX PoE lite
MikroTik RouterBOARD hEX lite
MikroTik RouterBOARD hAP ac lite
MikroTik RouterBOARD hEX PoE lite
MikroTik RouterBOARD hEX lite
+ MikroTik RouterBOARD Powerbox
MikroTik RouterBOARD LHG 5
MikroTik RouterBOARD cAP (EXPERIMENTAL)
MikroTik RouterBOARD mAP (EXPERIMENTAL)
MikroTik RouterBOARD LHG 5
MikroTik RouterBOARD cAP (EXPERIMENTAL)
MikroTik RouterBOARD mAP (EXPERIMENTAL)
* - MikroTik RouterBOARD 952Ui-5ac2nD
* - MikroTik RouterBOARD 962UiGS-5HacT2HnT
* - MikroTik RouterBOARD 750UP r2
* - MikroTik RouterBOARD 952Ui-5ac2nD
* - MikroTik RouterBOARD 962UiGS-5HacT2HnT
* - MikroTik RouterBOARD 750UP r2
+ * - MikroTik RouterBOARD 750P-PBr2
* - MikroTik RouterBOARD 750 r2
* - MikroTik RouterBOARD LHG 5nD
*
* - MikroTik RouterBOARD 750 r2
* - MikroTik RouterBOARD LHG 5nD
*
* Init the hEX (PoE) lite hardware (QCA953x).
* The 750UP r2 (hEX PoE lite) is nearly identical to the hAP, only without
* WLAN. The 750 r2 (hEX lite) is nearly identical to the 750UP r2, only
* Init the hEX (PoE) lite hardware (QCA953x).
* The 750UP r2 (hEX PoE lite) is nearly identical to the hAP, only without
* WLAN. The 750 r2 (hEX lite) is nearly identical to the 750UP r2, only
- * without USB and POE. It shares the same bootloader board identifier.
+ * without USB and POE. The 750P Pbr2 (Powerbox) is nearly identical to hEX PoE
+ * lite, only without USB. It shares the same bootloader board identifier.
*/
static void __init rb750upr2_setup(void)
{
*/
static void __init rb750upr2_setup(void)
{
if (strstr(mips_get_machine_name(), "750UP r2"))
flags |= RBSPI_HAS_USB | RBSPI_HAS_POE;
if (strstr(mips_get_machine_name(), "750UP r2"))
flags |= RBSPI_HAS_USB | RBSPI_HAS_POE;
+ /* differentiate the Powerbox from the hEX lite */
+ else if (strstr(mips_get_machine_name(), "750P r2"))
+ flags |= RBSPI_HAS_POE;
+
rbspi_952_750r2_setup(flags);
}
rbspi_952_750r2_setup(flags);
}
LOADER_TYPE := elf
KERNEL_INSTALL := 1
KERNEL := kernel-bin | lzma | loader-kernel
LOADER_TYPE := elf
KERNEL_INSTALL := 1
KERNEL := kernel-bin | lzma | loader-kernel
- SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-mapl-2nd
+ SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-750p-pbr2 rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-mapl-2nd
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 -e | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
endef
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 -e | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
endef