There is no reason to delete the DT PHY nodes
as you can just disable them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
pinctrl-names = "default";
reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
reset-delay-us = <2000>;
pinctrl-names = "default";
reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
reset-delay-us = <2000>;
-
- /delete-node/ ethernet-phy@0;
- /delete-node/ ethernet-phy@1;
+ðphy0 {
+ status = "disabled";
+};
+
+ðphy1 {
+ status = "disabled";
+};
+
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "devolo,magic-2-wifi-next";
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "devolo,magic-2-wifi-next";
mdio@90000 {
status = "okay";
mdio@90000 {
status = "okay";
-
- /delete-node/ ethernet-phy@0;
- /delete-node/ ethernet-phy@1;
- /delete-node/ ethernet-phy@3;
+ðphy0 {
+ status = "disabled";
+};
+
+ðphy1 {
+ status = "disabled";
+};
+
+ðphy3 {
+ status = "disabled";
+};
+
&wifi0 {
status = "okay";
nvmem-cell-names = "pre-calibration";
&wifi0 {
status = "okay";
nvmem-cell-names = "pre-calibration";
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
-
- /delete-node/ ethernet-phy@1;
- /delete-node/ ethernet-phy@2;
- /delete-node/ ethernet-phy@3;
- /delete-node/ ethernet-phy@4;
- /delete-node/ psgmii-phy@5;
+ðphy0 {
+ status = "disabled";
+};
+
+ðphy1 {
+ status = "disabled";
+};
+
+ðphy2 {
+ status = "disabled";
+};
+
+ðphy3 {
+ status = "disabled";
+};
+
+ðphy4 {
+ status = "disabled";
+};
+
+&psgmiiphy {
+ status = "disabled";
+};
+
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-1200";
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-1200";
mdio@90000 {
status = "okay";
mdio@90000 {
status = "okay";
-
- /delete-node/ ethernet-phy@1;
- /delete-node/ ethernet-phy@2;
- /delete-node/ ethernet-phy@3;
- /delete-node/ ethernet-phy@4;
- /delete-node/ psgmii-phy@5;
+
+ðphy1 {
+ status = "disabled";
+};
+
+ðphy2 {
+ status = "disabled";
+};
+
+ðphy3 {
+ status = "disabled";
+};
+
+ðphy4 {
+ status = "disabled";
+};
+
+&psgmiiphy {
+ status = "disabled";
+};
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
- /delete-node/ ethernet-phy@0;
- /delete-node/ ethernet-phy@1;
- /delete-node/ ethernet-phy@2;
- /delete-node/ ethernet-phy@3;
- /delete-node/ ethernet-phy@4;
- /delete-node/ psgmii-phy@5;
-
ethernet-phy@5 {
reg = <0x5>;
};
ethernet-phy@5 {
reg = <0x5>;
};
+ðphy0 {
+ status = "disabled";
+};
+
+ðphy1 {
+ status = "disabled";
+};
+
+ðphy2 {
+ status = "disabled";
+};
+
+ðphy3 {
+ status = "disabled";
+};
+
+ðphy4 {
+ status = "disabled";
+};
+
+&psgmiiphy {
+ status = "disabled";
+};
+
&wifi0 {
status = "okay";
nvmem-cell-names = "pre-calibration", "mac-address";
&wifi0 {
status = "okay";
nvmem-cell-names = "pre-calibration", "mac-address";