#define PHY_ID_RTL8218B_E 0x001cc981
#define PHY_ID_RTL8218B_I 0x001cca40
#define PHY_ID_RTL8390_GENERIC 0x001ccab0
+#define PHY_ID_RTL8393_I 0x001c8393
struct __attribute__ ((__packed__)) part {
uint16_t start;
pr_info("SERDES reset: %d\n", mac);
}
+int rtl839x_read_sds_phy(int phy_addr, int phy_reg)
+{
+ int offset = 0;
+ int reg;
+ u32 val;
+
+ if (phy_addr == 49)
+ offset = 0x100;
+
+ /* For the RTL8393 internal SerDes, we simulate a PHY ID in registers 2/3
+ * which would otherwise read as 0
+ */
+ if (soc_info.id == 0x8393) {
+ if (phy_reg == 2)
+ return 0x1c;
+ if (phy_reg == 3)
+ return 0x8393;
+ }
+
+ reg = (phy_reg << 1) & 0xfc;
+ val = sw_r32(RTL839X_SDS12_13_XSG0 + offset + 0x80 + reg);
+
+ if (phy_reg & 1)
+ val = (val >> 16) & 0xffff;
+ else
+ val &= 0xffff;
+ return val;
+}
+
+int rtl838x_read_sds_phy(int phy_addr, int phy_reg)
+{
+ int offset = 0;
+ u32 val;
+
+ if (phy_addr == 26)
+ offset = 0x100;
+ val = sw_r32(MAPLE_SDS4_FIB_REG0r + offset + (phy_reg << 2)) & 0xffff;
+
+ return val;
+}
+
+int rtl839x_write_sds_phy(int phy_addr, int phy_reg, u16 v)
+{
+ int offset = 0;
+ int reg;
+ u32 val;
+
+ if (phy_addr == 49)
+ offset = 0x100;
+
+ reg = (phy_reg << 1) & 0xfc;
+ val = v;
+ if (phy_reg & 1) {
+ val = val << 16;
+ sw_w32_mask(0xffff0000, val,
+ RTL839X_SDS12_13_XSG0 + offset + 0x80 + reg);
+ } else {
+ sw_w32_mask(0xffff, val,
+ RTL839X_SDS12_13_XSG0 + offset + 0x80 + reg);
+ }
+
+ return 0;
+}
+
+/* Read the link and speed status of the 2 internal SGMII/1000Base-X
+ * ports of the RTL838x SoCs
+ */
+static int rtl8380_read_status(struct phy_device *phydev)
+{
+ int err;
+ int phy_addr = phydev->mdio.addr;
+
+ err = genphy_read_status(phydev);
+
+ if (phydev->link) {
+ phydev->speed = SPEED_1000;
+ phydev->duplex = DUPLEX_FULL;
+ }
+
+ return err;
+}
+
+/* Read the link and speed status of the 2 internal SGMII/1000Base-X
+ * ports of the RTL8393 SoC
+ */
+static int rtl8393_read_status(struct phy_device *phydev)
+{
+ int offset = 0;
+ int err;
+ int phy_addr = phydev->mdio.addr;
+ u32 v;
+
+ err = genphy_read_status(phydev);
+ if (phy_addr == 49)
+ offset = 0x100;
+
+ if (phydev->link) {
+ phydev->speed = SPEED_100;
+ /* Read SPD_RD_00 (bit 13) and SPD_RD_01 (bit 6) out of the internal
+ * PHY registers
+ */
+ v = sw_r32(RTL839X_SDS12_13_XSG0 + offset + 0x80);
+ if (!(v & (1 << 13)) && (v & (1 << 6)))
+ phydev->speed = SPEED_1000;
+ phydev->duplex = DUPLEX_FULL;
+ }
+
+ return err;
+}
+
static struct fw_header *
rtl838x_request_fw(struct phy_device *phydev, const struct firmware *fw,
const char *name)
{
int addr = phydev->mdio.addr;
- return phydev->phy_id == PHY_ID_RTL8218B_E && addr < 8;
+ /* Both the RTL8214FC and the external RTL8218B have the same
+ * PHY ID. On the RTL838x, the RTL8218B can only be attached_dev
+ * at PHY IDs 0-7, while the RTL8214FC must be attached via
+ * the pair of SGMII/1000Base-X with higher PHY-IDs
+ */
+ if (soc_info.family == RTL8380_FAMILY_ID)
+ return phydev->phy_id == PHY_ID_RTL8218B_E && addr < 8;
+ else
+ return phydev->phy_id == PHY_ID_RTL8218B_E;
}
return 0;
}
+static int rtl8390_configure_serdes(struct phy_device *phydev)
+{
+ phydev_info(phydev, "Detected internal RTL8390 SERDES\n");
+
+ /* In autoneg state, force link, set SR4_CFG_EN_LINK_FIB1G */
+ sw_w32_mask(0, 1 << 18, RTL839X_SDS12_13_XSG0 + 0x0a);
+
+ /* Disable EEE: Clear FRE16_EEE_RSG_FIB1G, FRE16_EEE_STD_FIB1G,
+ * FRE16_C1_PWRSAV_EN_FIB1G, FRE16_C2_PWRSAV_EN_FIB1G
+ * and FRE16_EEE_QUIET_FIB1G
+ */
+ sw_w32_mask(0x1f << 10, 0, RTL839X_SDS12_13_XSG0 + 0xe0);
+
+ return 0;
+}
+
static int rtl8214fc_phy_probe(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
struct rtl838x_phy_priv *priv;
int addr = phydev->mdio.addr;
+ /* 839x has internal SerDes */
+ if (soc_info.id == 0x8393)
+ return -ENODEV;
+
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
priv->name = "RTL8218B (external)";
/* All base addresses of the PHYs start at multiples of 8 */
- if (!(addr % 8)) {
+ if (!(addr % 8) && soc_info.family == RTL8380_FAMILY_ID) {
/* Configuration must be done while patching still possible */
return rtl8380_configure_ext_rtl8218b(phydev);
}
return -ENODEV;
}
+static int rtl8393_serdes_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct rtl838x_phy_priv *priv;
+ int addr = phydev->mdio.addr;
+
+ pr_info("%s: id: %d\n", __func__, addr);
+ if (soc_info.family != RTL8390_FAMILY_ID)
+ return -ENODEV;
+
+ if (addr < 24)
+ return -ENODEV;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->name = "RTL8393 Serdes";
+ return rtl8390_configure_serdes(phydev);
+}
+
static int rtl8390_serdes_probe(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
static struct phy_driver rtl838x_phy_driver[] = {
{
- PHY_ID_MATCH_MODEL(PHY_ID_RTL8214FC),
- .name = "REATLTEK RTL8214C",
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8214C),
+ .name = "REALTEK RTL8214C",
.features = PHY_GBIT_FEATURES,
.match_phy_device = rtl8214c_match_phy_device,
.probe = rtl8214c_phy_probe,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_RTL8214FC),
- .name = "REATLTEK RTL8214FC",
+ .name = "REALTEK RTL8214FC",
.features = PHY_GBIT_FIBRE_FEATURES,
.match_phy_device = rtl8214fc_match_phy_device,
.probe = rtl8214fc_phy_probe,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_E),
- .name = "REATLTEK RTL8218B (external)",
+ .name = "REALTEK RTL8218B (external)",
.features = PHY_GBIT_FEATURES,
.match_phy_device = rtl8218b_ext_match_phy_device,
.probe = rtl8218b_ext_phy_probe,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_I),
- .name = "REATLTEK RTL8218B (internal)",
+ .name = "REALTEK RTL8218B (internal)",
.features = PHY_GBIT_FEATURES,
.probe = rtl8218b_int_phy_probe,
.suspend = genphy_suspend,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_I),
- .name = "REATLTEK RTL8380 SERDES",
+ .name = "REALTEK RTL8380 SERDES",
.features = PHY_GBIT_FIBRE_FEATURES,
.probe = rtl838x_serdes_probe,
.suspend = genphy_suspend,
.set_loopback = genphy_loopback,
.read_mmd = rtl8380_rtl8218b_read_mmd,
.write_mmd = rtl8380_rtl8218b_write_mmd,
+ .read_status = rtl8380_read_status,
+ },
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8393_I),
+ .name = "REALTEK RTL8393 SERDES",
+ .features = PHY_GBIT_FIBRE_FEATURES,
+ .probe = rtl8393_serdes_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ .read_status = rtl8393_read_status,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_RTL8390_GENERIC),
- .name = "REATLTEK RTL8390 Generic",
+ .name = "REALTEK RTL8390 Generic",
.features = PHY_GBIT_FIBRE_FEATURES,
.probe = rtl8390_serdes_probe,
.suspend = genphy_suspend,
projects / openwrt / staging / chunkeey.git / commitdiff