board: ti: am57xx: remove USB platform code
authorJean-Jacques Hiblot <jjhiblot@ti.com>
Thu, 29 Nov 2018 09:57:47 +0000 (10:57 +0100)
committerMarek Vasut <marex@denx.de>
Fri, 7 Dec 2018 15:31:46 +0000 (16:31 +0100)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
board/ti/am57xx/board.c

index bed2eb3c39206b317453c67b1717e3d0e95a415a..8dfb2eea43f0bc948081a37ba7355456ac56db56 100644 (file)
@@ -883,91 +883,6 @@ int spl_start_uboot(void)
 }
 #endif
 
-#if defined(CONFIG_USB_DWC3) && !CONFIG_IS_ENABLED(DM_USB)
-static struct dwc3_device usb_otg_ss2 = {
-       .maximum_speed = USB_SPEED_HIGH,
-       .base = DRA7_USB_OTG_SS2_BASE,
-       .tx_fifo_resize = false,
-       .index = 1,
-};
-
-static struct dwc3_omap_device usb_otg_ss2_glue = {
-       .base = (void *)DRA7_USB_OTG_SS2_GLUE_BASE,
-       .utmi_mode = DWC3_OMAP_UTMI_MODE_SW,
-       .index = 1,
-};
-
-static struct ti_usb_phy_device usb_phy2_device = {
-       .usb2_phy_power = (void *)DRA7_USB2_PHY2_POWER,
-       .index = 1,
-};
-
-int usb_gadget_handle_interrupts(int index)
-{
-       u32 status;
-
-       status = dwc3_omap_uboot_interrupt_status(index);
-       if (status)
-               dwc3_uboot_handle_interrupt(index);
-
-       return 0;
-}
-
-int board_usb_init(int index, enum usb_init_type init)
-{
-       enable_usb_clocks(index);
-       switch (index) {
-       case 0:
-               if (init == USB_INIT_DEVICE) {
-                       printf("port %d can't be used as device\n", index);
-                       disable_usb_clocks(index);
-                       return -EINVAL;
-               }
-               break;
-       case 1:
-               if (init == USB_INIT_DEVICE) {
-#ifdef CONFIG_USB_DWC3
-                       usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL;
-                       usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID;
-                       ti_usb_phy_uboot_init(&usb_phy2_device);
-                       dwc3_omap_uboot_init(&usb_otg_ss2_glue);
-                       dwc3_uboot_init(&usb_otg_ss2);
-#endif
-               } else {
-                       printf("port %d can't be used as host\n", index);
-                       disable_usb_clocks(index);
-                       return -EINVAL;
-               }
-
-               break;
-       default:
-               printf("Invalid Controller Index\n");
-       }
-
-       return 0;
-}
-
-int board_usb_cleanup(int index, enum usb_init_type init)
-{
-#ifdef CONFIG_USB_DWC3
-       switch (index) {
-       case 0:
-       case 1:
-               if (init == USB_INIT_DEVICE) {
-                       ti_usb_phy_uboot_exit(index);
-                       dwc3_uboot_exit(index);
-                       dwc3_omap_uboot_exit(index);
-               }
-               break;
-       default:
-               printf("Invalid Controller Index\n");
-       }
-#endif
-       disable_usb_clocks(index);
-       return 0;
-}
-#endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */
-
 #ifdef CONFIG_DRIVER_TI_CPSW
 
 /* Delay value to add to calibrated value */