new boards should not use this option.
config SYS_TEXT_BASE
- depends on SPARC || ARC || X86 || ARCH_UNIPHIER
+ depends on SPARC || ARC || X86 || ARCH_UNIPHIER || ARCH_ZYNQMP
hex "Text Base"
help
TODO: Move CONFIG_SYS_TEXT_BASE for all the architecture
select DM_SPI
select DM_SPI_FLASH
-config TARGET_XILINX_ZYNQMP
+config ARCH_ZYNQMP
bool "Support Xilinx ZynqMP Platform"
select ARM64
source "arch/arm/cpu/armv7/Kconfig"
+source "arch/arm/cpu/armv8/zynqmp/Kconfig"
+
source "arch/arm/cpu/armv8/Kconfig"
source "arch/arm/imx-common/Kconfig"
source "board/woodburn/Kconfig"
source "board/work-microwave/work_92105/Kconfig"
source "board/xaeniax/Kconfig"
-source "board/xilinx/zynqmp/Kconfig"
source "board/zipitz2/Kconfig"
source "arch/arm/Kconfig.debug"
obj-y += transition.o
obj-$(CONFIG_FSL_LSCH3) += fsl-lsch3/
-obj-$(CONFIG_TARGET_XILINX_ZYNQMP) += zynqmp/
+obj-$(CONFIG_ARCH_ZYNQMP) += zynqmp/
--- /dev/null
+if ARCH_ZYNQMP
+
+choice
+ prompt "Xilinx ZynqMP board select"
+
+config TARGET_ZYNQMP_EP
+ bool "ZynqMP EP Board"
+
+endchoice
+
+config SYS_BOARD
+ default "zynqmp"
+
+config SYS_VENDOR
+ default "xilinx"
+
+config SYS_SOC
+ default "zynqmp"
+
+config SYS_CONFIG_NAME
+ default "xilinx_zynqmp_ep" if TARGET_ZYNQMP_EP
+
+endif
obj-y += clk.o
obj-y += cpu.o
obj-$(CONFIG_MP) += mp.o
+obj-y += slcr.o
printf("R5 lockstep mode\n");
set_r5_tcm_mode(LOCK);
set_r5_halt_mode(HALT, LOCK);
-
- if (boot_addr == 0)
- set_r5_start(0);
- else
- set_r5_start(1);
-
+ set_r5_start(boot_addr);
enable_clock_r5();
release_r5_reset(LOCK);
set_r5_halt_mode(RELEASE, LOCK);
--- /dev/null
+/*
+ * (C) Copyright 2014 - 2015 Xilinx, Inc.
+ * Michal Simek <michal.simek@xilinx.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <malloc.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/clk.h>
+
+/*
+ * zynq_slcr_mio_get_status - Get the status of MIO peripheral.
+ *
+ * @peri_name: Name of the peripheral for checking MIO status
+ * @get_pins: Pointer to array of get pin for this peripheral
+ * @num_pins: Number of pins for this peripheral
+ * @mask: Mask value
+ * @check_val: Required check value to get the status of periph
+ */
+struct zynq_slcr_mio_get_status {
+ const char *peri_name;
+ const int *get_pins;
+ int num_pins;
+ u32 mask;
+ u32 check_val;
+};
+
+static const struct zynq_slcr_mio_get_status mio_periphs[] = {
+};
+
+/*
+ * zynq_slcr_get_mio_pin_status - Get the MIO pin status of peripheral.
+ *
+ * @periph: Name of the peripheral
+ *
+ * Returns count to indicate the number of pins configured for the
+ * given @periph.
+ */
+int zynq_slcr_get_mio_pin_status(const char *periph)
+{
+ const struct zynq_slcr_mio_get_status *mio_ptr;
+ int val, i, j;
+ int mio = 0;
+
+ for (i = 0; i < ARRAY_SIZE(mio_periphs); i++) {
+ if (strcmp(periph, mio_periphs[i].peri_name) == 0) {
+ mio_ptr = &mio_periphs[i];
+ for (j = 0; j < mio_ptr->num_pins; j++) {
+ val = readl(&slcr_base->mio_pin
+ [mio_ptr->get_pins[j]]);
+ if ((val & mio_ptr->mask) == mio_ptr->check_val)
+ mio++;
+ }
+ break;
+ }
+ }
+
+ return mio;
+}
zynq-microzed.dtb \
zynq-picozed.dtb \
zynq-zc770-xm010.dtb \
+ zynq-zc770-xm011.dtb \
zynq-zc770-xm012.dtb \
zynq-zc770-xm013.dtb
dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb
* Xilinx Zynq 7000 DTSI
* Describes the hardware common to all Zynq 7000-based boards.
*
- * Copyright (C) 2013 Xilinx, Inc.
+ * Copyright (C) 2011 - 2015 Xilinx
*
* SPDX-License-Identifier: GPL-2.0+
*/
reg = <0>;
clocks = <&clkc 3>;
clock-latency = <1000>;
+ cpu0-supply = <®ulator_vccpint>;
operating-points = <
/* kHz uV */
666667 1000000
333334 1000000
- 222223 1000000
>;
};
reg = < 0xf8891000 0x1000 0xf8893000 0x1000 >;
};
- amba {
+ regulator_vccpint: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCCPINT";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ amba: amba {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&intc>;
ranges;
- i2c0: zynq-i2c@e0004000 {
+ adc: adc@f8007100 {
+ compatible = "xlnx,zynq-xadc-1.00.a";
+ reg = <0xf8007100 0x20>;
+ interrupts = <0 7 4>;
+ interrupt-parent = <&intc>;
+ clocks = <&clkc 12>;
+ };
+
+ can0: can@e0008000 {
+ compatible = "xlnx,zynq-can-1.0";
+ status = "disabled";
+ clocks = <&clkc 19>, <&clkc 36>;
+ clock-names = "can_clk", "pclk";
+ reg = <0xe0008000 0x1000>;
+ interrupts = <0 28 4>;
+ interrupt-parent = <&intc>;
+ tx-fifo-depth = <0x40>;
+ rx-fifo-depth = <0x40>;
+ };
+
+ can1: can@e0009000 {
+ compatible = "xlnx,zynq-can-1.0";
+ status = "disabled";
+ clocks = <&clkc 20>, <&clkc 37>;
+ clock-names = "can_clk", "pclk";
+ reg = <0xe0009000 0x1000>;
+ interrupts = <0 51 4>;
+ interrupt-parent = <&intc>;
+ tx-fifo-depth = <0x40>;
+ rx-fifo-depth = <0x40>;
+ };
+
+ gpio0: gpio@e000a000 {
+ compatible = "xlnx,zynq-gpio-1.0";
+ #gpio-cells = <2>;
+ clocks = <&clkc 42>;
+ gpio-controller;
+ interrupt-parent = <&intc>;
+ interrupts = <0 20 4>;
+ reg = <0xe000a000 0x1000>;
+ };
+
+ i2c0: i2c@e0004000 {
compatible = "cdns,i2c-r1p10";
status = "disabled";
clocks = <&clkc 38>;
#size-cells = <0>;
};
- i2c1: zynq-i2c@e0005000 {
+ i2c1: i2c@e0005000 {
compatible = "cdns,i2c-r1p10";
status = "disabled";
clocks = <&clkc 39>;
intc: interrupt-controller@f8f01000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <3>;
- #address-cells = <1>;
interrupt-controller;
reg = <0xF8F01000 0x1000>,
<0xF8F00100 0x100>;
};
- L2: cache-controller {
+ L2: cache-controller@f8f02000 {
compatible = "arm,pl310-cache";
reg = <0xF8F02000 0x1000>;
+ interrupts = <0 2 4>;
arm,data-latency = <3 2 2>;
arm,tag-latency = <2 2 2>;
cache-unified;
cache-level = <2>;
};
- uart0: uart@e0000000 {
- compatible = "xlnx,xuartps";
+ mc: memory-controller@f8006000 {
+ compatible = "xlnx,zynq-ddrc-a05";
+ reg = <0xf8006000 0x1000>;
+ };
+
+ uart0: serial@e0000000 {
+ compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "disabled";
clocks = <&clkc 23>, <&clkc 40>;
- clock-names = "ref_clk", "aper_clk";
+ clock-names = "uart_clk", "pclk";
reg = <0xE0000000 0x1000>;
interrupts = <0 27 4>;
};
- uart1: uart@e0001000 {
- compatible = "xlnx,xuartps";
+ uart1: serial@e0001000 {
+ compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "disabled";
clocks = <&clkc 24>, <&clkc 41>;
- clock-names = "ref_clk", "aper_clk";
+ clock-names = "uart_clk", "pclk";
reg = <0xE0001000 0x1000>;
interrupts = <0 50 4>;
};
spi0: spi@e0006000 {
- compatible = "xlnx,zynq-spi";
+ compatible = "xlnx,zynq-spi-r1p6";
reg = <0xe0006000 0x1000>;
status = "disabled";
interrupt-parent = <&intc>;
};
spi1: spi@e0007000 {
- compatible = "xlnx,zynq-spi";
+ compatible = "xlnx,zynq-spi-r1p6";
reg = <0xe0007000 0x1000>;
status = "disabled";
interrupt-parent = <&intc>;
};
gem0: ethernet@e000b000 {
- compatible = "cdns,gem";
- reg = <0xe000b000 0x4000>;
+ compatible = "cdns,zynq-gem", "cdns,gem";
+ reg = <0xe000b000 0x1000>;
status = "disabled";
interrupts = <0 22 4>;
clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>;
clock-names = "pclk", "hclk", "tx_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
gem1: ethernet@e000c000 {
- compatible = "cdns,gem";
- reg = <0xe000c000 0x4000>;
+ compatible = "cdns,zynq-gem", "cdns,gem";
+ reg = <0xe000c000 0x1000>;
status = "disabled";
interrupts = <0 45 4>;
clocks = <&clkc 31>, <&clkc 31>, <&clkc 14>;
clock-names = "pclk", "hclk", "tx_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
- sdhci0: ps7-sdhci@e0100000 {
+ sdhci0: sdhci@e0100000 {
compatible = "arasan,sdhci-8.9a";
status = "disabled";
clock-names = "clk_xin", "clk_ahb";
reg = <0xe0100000 0x1000>;
} ;
- sdhci1: ps7-sdhci@e0101000 {
+ sdhci1: sdhci@e0101000 {
compatible = "arasan,sdhci-8.9a";
status = "disabled";
clock-names = "clk_xin", "clk_ahb";
slcr: slcr@f8000000 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "xlnx,zynq-slcr", "syscon";
+ compatible = "xlnx,zynq-slcr", "syscon", "simple-bus";
reg = <0xF8000000 0x1000>;
ranges;
clkc: clkc@100 {
#clock-cells = <1>;
compatible = "xlnx,ps7-clkc";
- ps-clk-frequency = <33333333>;
fclk-enable = <0>;
clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x",
"cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x",
"dbg_trc", "dbg_apb";
reg = <0x100 0x100>;
};
+
+ pinctrl0: pinctrl@700 {
+ compatible = "xlnx,pinctrl-zynq";
+ reg = <0x700 0x200>;
+ syscon = <&slcr>;
+ };
+ };
+
+ dmac_s: dmac@f8003000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0xf8003000 0x1000>;
+ interrupt-parent = <&intc>;
+ interrupt-names = "abort", "dma0", "dma1", "dma2", "dma3",
+ "dma4", "dma5", "dma6", "dma7";
+ interrupts = <0 13 4>,
+ <0 14 4>, <0 15 4>,
+ <0 16 4>, <0 17 4>,
+ <0 40 4>, <0 41 4>,
+ <0 42 4>, <0 43 4>;
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <4>;
+ clocks = <&clkc 27>;
+ clock-names = "apb_pclk";
+ };
+
+ devcfg: devcfg@f8007000 {
+ compatible = "xlnx,zynq-devcfg-1.0";
+ reg = <0xf8007000 0x100>;
};
global_timer: timer@f8f00200 {
clocks = <&clkc 4>;
};
- ttc0: ttc0@f8001000 {
+ ttc0: timer@f8001000 {
interrupt-parent = <&intc>;
- interrupts = < 0 10 4 0 11 4 0 12 4 >;
+ interrupts = <0 10 4>, <0 11 4>, <0 12 4>;
compatible = "cdns,ttc";
clocks = <&clkc 6>;
reg = <0xF8001000 0x1000>;
};
- ttc1: ttc1@f8002000 {
+ ttc1: timer@f8002000 {
interrupt-parent = <&intc>;
- interrupts = < 0 37 4 0 38 4 0 39 4 >;
+ interrupts = <0 37 4>, <0 38 4>, <0 39 4>;
compatible = "cdns,ttc";
clocks = <&clkc 6>;
reg = <0xF8002000 0x1000>;
};
- scutimer: scutimer@f8f00600 {
+
+ scutimer: timer@f8f00600 {
interrupt-parent = <&intc>;
interrupts = < 1 13 0x301 >;
compatible = "arm,cortex-a9-twd-timer";
reg = < 0xf8f00600 0x20 >;
clocks = <&clkc 4>;
} ;
+
+ usb0: usb@e0002000 {
+ compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2";
+ status = "disabled";
+ clocks = <&clkc 28>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 21 4>;
+ reg = <0xe0002000 0x1000>;
+ phy_type = "ulpi";
+ };
+
+ usb1: usb@e0003000 {
+ compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2";
+ status = "disabled";
+ clocks = <&clkc 29>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 44 4>;
+ reg = <0xe0003000 0x1000>;
+ phy_type = "ulpi";
+ };
+
+ watchdog0: watchdog@f8005000 {
+ clocks = <&clkc 45>;
+ compatible = "cdns,wdt-r1p2";
+ interrupt-parent = <&intc>;
+ interrupts = <0 9 1>;
+ reg = <0xf8005000 0x1000>;
+ timeout-sec = <10>;
+ };
};
};
/*
* Xilinx ZC702 board DTS
*
- * Copyright (C) 2013 Xilinx, Inc.
+ * Copyright (C) 2011 - 2015 Xilinx
+ * Copyright (C) 2012 National Instruments Corp.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include "zynq-7000.dtsi"
/ {
- model = "Zynq ZC702 Board";
+ model = "Zynq ZC702 Development Board";
compatible = "xlnx,zynq-zc702", "xlnx,zynq-7000";
aliases {
+ ethernet0 = &gem0;
+ i2c0 = &i2c0;
serial0 = &uart1;
};
memory {
device_type = "memory";
- reg = <0 0x40000000>;
+ reg = <0x0 0x40000000>;
};
+
+ chosen {
+ bootargs = "earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw14 {
+ label = "sw14";
+ gpios = <&gpio0 12 0>;
+ linux,code = <108>; /* down */
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ sw13 {
+ label = "sw13";
+ gpios = <&gpio0 14 0>;
+ linux,code = <103>; /* up */
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ds23 {
+ label = "ds23";
+ gpios = <&gpio0 10 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&amba {
+ ocm: sram@fffc0000 {
+ compatible = "mmio-sram";
+ reg = <0xfffc0000 0x10000>;
+ };
+};
+
+&can0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_default>;
+};
+
+&clkc {
+ ps-clk-frequency = <33333333>;
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem0_default>;
+
+ ethernet_phy: ethernet-phy@7 {
+ reg = <7>;
+ };
+};
+
+&gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+
+ i2cswitch@74 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ si570: clock-generator@5d {
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ temperature-stability = <50>;
+ reg = <0x5d>;
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ eeprom@54 {
+ compatible = "at,24c08";
+ reg = <0x54>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+ };
+
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ hwmon@52 {
+ compatible = "ti,ucd9248";
+ reg = <52>;
+ };
+ hwmon@53 {
+ compatible = "ti,ucd9248";
+ reg = <53>;
+ };
+ hwmon@54 {
+ compatible = "ti,ucd9248";
+ reg = <54>;
+ };
+ };
+ };
+};
+
+&pinctrl0 {
+ pinctrl_can0_default: can0-default {
+ mux {
+ function = "can0";
+ groups = "can0_9_grp";
+ };
+
+ conf {
+ groups = "can0_9_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO46";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO47";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem0_default: gem0-default {
+ mux {
+ function = "ethernet0";
+ groups = "ethernet0_0_grp";
+ };
+
+ conf {
+ groups = "ethernet0_0_grp";
+ slew-rate = <0>;
+ io-standard = <4>;
+ };
+
+ conf-rx {
+ pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio0";
+ groups = "mdio0_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_gpio0_default: gpio0-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp",
+ "gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp",
+ "gpio0_13_grp", "gpio0_14_grp";
+ };
+
+ conf {
+ groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp",
+ "gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp",
+ "gpio0_13_grp", "gpio0_14_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-pull-up {
+ pins = "MIO9", "MIO10", "MIO11", "MIO12", "MIO13", "MIO14";
+ bias-pull-up;
+ };
+
+ conf-pull-none {
+ pins = "MIO7", "MIO8";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_10_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_10_grp";
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_sdhci0_default: sdhci0-default {
+ mux {
+ groups = "sdio0_2_grp";
+ function = "sdio0";
+ };
+
+ conf {
+ groups = "sdio0_2_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "gpio0_0_grp";
+ function = "sdio0_cd";
+ };
+
+ conf-cd {
+ groups = "gpio0_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ mux-wp {
+ groups = "gpio0_15_grp";
+ function = "sdio0_wp";
+ };
+
+ conf-wp {
+ groups = "gpio0_15_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_10_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_10_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO49";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO48";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO29", "MIO31", "MIO36";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO28", "MIO30", "MIO32", "MIO33", "MIO34",
+ "MIO35", "MIO37", "MIO38", "MIO39";
+ bias-disable;
+ };
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci0_default>;
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
};
/*
* Xilinx ZC706 board DTS
*
- * Copyright (C) 2013 Xilinx, Inc.
+ * Copyright (C) 2011 - 2015 Xilinx
+ * Copyright (C) 2012 National Instruments Corp.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include "zynq-7000.dtsi"
/ {
- model = "Zynq ZC706 Board";
+ model = "Zynq ZC706 Development Board";
compatible = "xlnx,zynq-zc706", "xlnx,zynq-7000";
aliases {
+ ethernet0 = &gem0;
+ i2c0 = &i2c0;
serial0 = &uart1;
};
memory {
device_type = "memory";
- reg = <0 0x40000000>;
+ reg = <0x0 0x40000000>;
};
+
+ chosen {
+ bootargs = "earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&clkc {
+ ps-clk-frequency = <33333333>;
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem0_default>;
+
+ ethernet_phy: ethernet-phy@7 {
+ reg = <7>;
+ };
+};
+
+&gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+
+ i2cswitch@74 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ si570: clock-generator@5d {
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ temperature-stability = <50>;
+ reg = <0x5d>;
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ eeprom@54 {
+ compatible = "at,24c08";
+ reg = <0x54>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+ };
+
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ ucd90120@65 {
+ compatible = "ti,ucd90120";
+ reg = <0x65>;
+ };
+ };
+ };
+};
+
+&pinctrl0 {
+ pinctrl_gem0_default: gem0-default {
+ mux {
+ function = "ethernet0";
+ groups = "ethernet0_0_grp";
+ };
+
+ conf {
+ groups = "ethernet0_0_grp";
+ slew-rate = <0>;
+ io-standard = <4>;
+ };
+
+ conf-rx {
+ pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21";
+ low-power-enable;
+ bias-disable;
+ };
+
+ mux-mdio {
+ function = "mdio0";
+ groups = "mdio0_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_gpio0_default: gpio0-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_7_grp", "gpio0_46_grp", "gpio0_47_grp";
+ };
+
+ conf {
+ groups = "gpio0_7_grp", "gpio0_46_grp", "gpio0_47_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-pull-up {
+ pins = "MIO46", "MIO47";
+ bias-pull-up;
+ };
+
+ conf-pull-none {
+ pins = "MIO7";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_10_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_10_grp";
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_sdhci0_default: sdhci0-default {
+ mux {
+ groups = "sdio0_2_grp";
+ function = "sdio0";
+ };
+
+ conf {
+ groups = "sdio0_2_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "gpio0_14_grp";
+ function = "sdio0_cd";
+ };
+
+ conf-cd {
+ groups = "gpio0_14_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ mux-wp {
+ groups = "gpio0_15_grp";
+ function = "sdio0_wp";
+ };
+
+ conf-wp {
+ groups = "gpio0_15_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_10_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_10_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO49";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO48";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO29", "MIO31", "MIO36";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO28", "MIO30", "MIO32", "MIO33", "MIO34",
+ "MIO35", "MIO37", "MIO38", "MIO39";
+ bias-disable;
+ };
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci0_default>;
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
};
/*
* Xilinx ZC770 XM010 board DTS
*
- * Copyright (C) 2013 Xilinx, Inc.
+ * Copyright (C) 2013 - 2015 Xilinx, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include "zynq-7000.dtsi"
/ {
- model = "Zynq ZC770 XM010 Board";
compatible = "xlnx,zynq-zc770-xm010", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
aliases {
+ ethernet0 = &gem0;
+ i2c0 = &i2c0;
serial0 = &uart1;
- spi1 = &spi1;
+ spi0 = &spi1;
};
- memory {
+ chosen {
+ bootargs = "console=ttyPS0,115200 root=/dev/ram rw earlyprintk";
+ linux,stdout-path = &uart1;
+ stdout-path = &uart1;
+ };
+
+ memory@0 {
device_type = "memory";
- reg = <0 0x40000000>;
+ reg = <0x0 0x40000000>;
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
};
};
&spi1 {
status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+ flash@0 {
+ compatible = "sst25wf080";
+ reg = <1>;
+ spi-max-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@test {
+ label = "spi-flash";
+ reg = <0x0 0x100000>;
+ };
+ };
+};
+
+&can0 {
+ status = "okay";
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+
+ ethernet_phy: ethernet-phy@7 {
+ reg = <7>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ m24c02_eeprom@52 {
+ compatible = "at,24c02";
+ reg = <0x52>;
+ };
+
+};
+
+&sdhci0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
};
--- /dev/null
+/*
+ * Xilinx ZC770 XM013 board DTS
+ *
+ * Copyright (C) 2013 Xilinx, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+/dts-v1/;
+#include "zynq-7000.dtsi"
+/ {
+ compatible = "xlnx,zynq-zc770-xm011", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
+
+ aliases {
+ i2c0 = &i2c1;
+ serial0 = &uart1;
+ spi0 = &spi0;
+ };
+
+ chosen {
+ bootargs = "console=ttyPS0,115200 root=/dev/ram rw earlyprintk";
+ linux,stdout-path = &uart1;
+ stdout-path = &uart1;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x40000000>;
+ };
+
+ usb_phy1: phy1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&spi0 {
+ status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+};
+
+&can0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ m24c02_eeprom@52 {
+ compatible = "at,24c02";
+ reg = <0x52>;
+ };
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy1>;
+};
/*
* Xilinx ZC770 XM012 board DTS
*
- * Copyright (C) 2013 Xilinx, Inc.
+ * Copyright (C) 2013 - 2015 Xilinx, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include "zynq-7000.dtsi"
/ {
- model = "Zynq ZC770 XM012 Board";
compatible = "xlnx,zynq-zc770-xm012", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
serial0 = &uart1;
+ spi0 = &spi1;
};
- memory {
+ chosen {
+ bootargs = "console=ttyPS0,115200 root=/dev/ram rw earlyprintk";
+ linux,stdout-path = &uart1;
+ stdout-path = &uart1;
+ };
+
+ memory@0 {
device_type = "memory";
- reg = <0 0x40000000>;
+ reg = <0x0 0x40000000>;
+ };
+};
+
+&spi1 {
+ status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+};
+
+&can1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ m24c02_eeprom@52 {
+ compatible = "at,24c02";
+ reg = <0x52>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ m24c02_eeprom@52 {
+ compatible = "at,24c02";
+ reg = <0x52>;
};
};
+
+&uart1 {
+ status = "okay";
+};
#include "zynq-7000.dtsi"
/ {
- model = "Zynq ZC770 XM013 Board";
compatible = "xlnx,zynq-zc770-xm013", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
aliases {
+ ethernet0 = &gem1;
+ i2c0 = &i2c1;
serial0 = &uart0;
+ spi0 = &spi0;
};
- memory {
+ chosen {
+ bootargs = "console=ttyPS0,115200 root=/dev/ram rw earlyprintk";
+ linux,stdout-path = &uart0;
+ stdout-path = &uart0;
+ };
+
+ memory@0 {
device_type = "memory";
- reg = <0 0x40000000>;
+ reg = <0x0 0x40000000>;
+ };
+};
+
+&spi0 {
+ status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+ eeprom: at25@0 {
+ at25,byte-len = <8192>;
+ at25,addr-mode = <2>;
+ at25,page-size = <32>;
+
+ compatible = "atmel,at25";
+ reg = <2>;
+ spi-max-frequency = <1000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&gem1 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+
+ ethernet_phy: ethernet-phy@7 {
+ reg = <7>;
};
};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ si570: clock-generator@55 {
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ temperature-stability = <50>;
+ reg = <0x55>;
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
/*
* Xilinx ZED board DTS
*
- * Copyright (C) 2013 Xilinx, Inc.
+ * Copyright (C) 2011 - 2015 Xilinx
+ * Copyright (C) 2012 National Instruments Corp.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include "zynq-7000.dtsi"
/ {
- model = "Zynq ZED Board";
+ model = "Zynq Zed Development Board";
compatible = "xlnx,zynq-zed", "xlnx,zynq-7000";
aliases {
+ ethernet0 = &gem0;
serial0 = &uart1;
};
memory {
device_type = "memory";
- reg = <0 0x20000000>;
+ reg = <0x0 0x20000000>;
};
+
+ chosen {
+ bootargs = "earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&clkc {
+ ps-clk-frequency = <33333333>;
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+
+ ethernet_phy: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
};
/*
* Digilent ZYBO board DTS
*
- * Copyright (C) 2013 Xilinx, Inc.
+ * Copyright (C) 2011 - 2015 Xilinx
+ * Copyright (C) 2012 National Instruments Corp.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include "zynq-7000.dtsi"
/ {
- model = "Zynq ZYBO Board";
- compatible = "xlnx,zynq-zybo", "xlnx,zynq-7000";
+ model = "Zynq ZYBO Development Board";
+ compatible = "digilent,zynq-zybo", "xlnx,zynq-7000";
aliases {
+ ethernet0 = &gem0;
serial0 = &uart1;
};
memory {
device_type = "memory";
- reg = <0 0x20000000>;
+ reg = <0x0 0x20000000>;
};
+
+ chosen {
+ bootargs = "earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+};
+
+&clkc {
+ ps-clk-frequency = <50000000>;
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+
+ ethernet_phy: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
};
#define ZYNQ_SERIAL_BASEADDR0 0xFF000000
#define ZYNQ_SERIAL_BASEADDR1 0xFF001000
+#define ZYNQ_GEM_BASEADDR0 0xFF0B0000
+#define ZYNQ_GEM_BASEADDR1 0xFF0C0000
+#define ZYNQ_GEM_BASEADDR2 0xFF0D0000
+#define ZYNQ_GEM_BASEADDR3 0xFF0E0000
+
#define ZYNQ_SPI_BASEADDR0 0xFF040000
#define ZYNQ_SPI_BASEADDR1 0xFF050000
#define ZYNQ_SDHCI_BASEADDR0 0xFF160000
#define ZYNQ_SDHCI_BASEADDR1 0xFF170000
+#define ZYNQMP_SATA_BASEADDR 0xFD0C0000
+
#define ZYNQMP_CRL_APB_BASEADDR 0xFF5E0000
#define ZYNQMP_CRL_APB_TIMESTAMP_REF_CTRL_CLKACT 0x1000000
#define EMMC_MODE 0x00000006
#define JTAG_MODE 0x00000000
+#define ZYNQMP_IOU_SLCR_BASEADDR 0xFF180000
+
+struct iou_slcr_regs {
+ u32 mio_pin[78];
+ u32 reserved[442];
+};
+
+#define slcr_base ((struct iou_slcr_regs *)ZYNQMP_IOU_SLCR_BASEADDR)
+
#define ZYNQMP_RPU_BASEADDR 0xFF9A0000
struct rpu_regs {
#ifndef _ASM_ARCH_SYS_PROTO_H
#define _ASM_ARCH_SYS_PROTO_H
+/* Setup clk for network */
+static inline void zynq_slcr_gem_clk_setup(u32 gem_id, unsigned long clk_rate)
+{
+}
+
int zynq_sdhci_init(unsigned long regbase);
+int zynq_slcr_get_mio_pin_status(const char *periph);
unsigned int zynqmp_get_silicon_version(void);
ifneq ($(wildcard $(srctree)/$(src)/ps7_init_gpl.c),)
init-objs := ps7_init_gpl.o
$(if $(CONFIG_SPL_BUILD),\
-$(warning Put custom ps7_init_gpl.c/h to board/xilinx/zynq/custome_hw_platform/))
+$(warning Put custom ps7_init_gpl.c/h to board/xilinx/zynq/custom_hw_platform/))
endif
endif
+++ /dev/null
-if TARGET_XILINX_ZYNQMP
-
-config SYS_BOARD
- default "zynqmp"
-
-config SYS_VENDOR
- default "xilinx"
-
-config SYS_SOC
- default "zynqmp"
-
-config SYS_CONFIG_NAME
- default "xilinx_zynqmp"
-
-endif
-XILINX_ZYNQMP BOARD
+XILINX_ZYNQMP_EP BOARD
M: Michal Simek <michal.simek@xilinx.com>
S: Maintained
F: board/xilinx/zynqmp/
F: include/configs/xilinx_zynqmp.h
-F: configs/xilinx_zynqmp_defconfig
+F: include/configs/xilinx_zynqmp_ep.h
+F: configs/xilinx_zynqmp_ep_defconfig
#include <common.h>
#include <netdev.h>
+#include <ahci.h>
+#include <scsi.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
int board_init(void)
{
+ printf("EL Level:\tEL%d\n", current_el());
+
return 0;
}
{
}
+#ifdef CONFIG_SCSI_AHCI_PLAT
+void scsi_init(void)
+{
+ ahci_init((void __iomem *)ZYNQMP_SATA_BASEADDR);
+ scsi_scan(1);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ u32 ret = 0;
+
+#if defined(CONFIG_ZYNQ_GEM)
+# if defined(CONFIG_ZYNQ_GEM0)
+ ret |= zynq_gem_initialize(bis, ZYNQ_GEM_BASEADDR0,
+ CONFIG_ZYNQ_GEM_PHY_ADDR0, 0);
+# endif
+# if defined(CONFIG_ZYNQ_GEM1)
+ ret |= zynq_gem_initialize(bis, ZYNQ_GEM_BASEADDR1,
+ CONFIG_ZYNQ_GEM_PHY_ADDR1, 0);
+# endif
+# if defined(CONFIG_ZYNQ_GEM2)
+ ret |= zynq_gem_initialize(bis, ZYNQ_GEM_BASEADDR2,
+ CONFIG_ZYNQ_GEM_PHY_ADDR2, 0);
+# endif
+# if defined(CONFIG_ZYNQ_GEM3)
+ ret |= zynq_gem_initialize(bis, ZYNQ_GEM_BASEADDR3,
+ CONFIG_ZYNQ_GEM_PHY_ADDR3, 0);
+# endif
+#endif
+ return ret;
+}
+
#ifdef CONFIG_CMD_MMC
int board_mmc_init(bd_t *bd)
{
#include <common.h>
#include <command.h>
+static int cpu_status_all(void)
+{
+ unsigned long cpuid;
+
+ for (cpuid = 0; ; cpuid++) {
+ if (!is_core_valid(cpuid)) {
+ if (cpuid == 0) {
+ printf("Core num: %lu is not valid\n", cpuid);
+ return 1;
+ }
+ break;
+ }
+ cpu_status(cpuid);
+ }
+
+ return 0;
+}
+
static int
cpu_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
unsigned long cpuid;
+ if (argc == 2 && strncmp(argv[1], "status", 6) == 0)
+ return cpu_status_all();
+
if (argc < 3)
return CMD_RET_USAGE;
#ifdef CONFIG_SYS_LONGHELP
static char cpu_help_text[] =
"<num> reset - Reset cpu <num>\n"
+ "cpu status - Status of all cpus\n"
"cpu <num> status - Status of cpu <num>\n"
"cpu <num> disable - Disable cpu <num>\n"
"cpu <num> release <addr> [args] - Release cpu <num> at <addr> with [args]"
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_XILINX_ZYNQMP=y
-CONFIG_DEFAULT_DEVICE_TREE="zynqmp"
-# CONFIG_CMD_CONSOLE is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_ENV_EXISTS is not set
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
-# CONFIG_CMD_NET is not set
-# CONFIG_CMD_NFS is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_TIMER=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_DEFAULT_DEVICE_TREE="zynqmp-ep"
+# CONFIG_CMD_CONSOLE is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_ENV_EXISTS is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_NET is not set
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_SYS_TEXT_BASE=0x8000000
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_ZYNQ=y
+CONFIG_TARGET_ZYNQ_ZC770=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-zc770-xm011"
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_SYS_EXTRA_OPTIONS="ZC770_XM011"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_SETEXPR is not set
-Zynq SPI controller Device Tree Bindings
-----------------------------------------
+Cadence SPI controller Device Tree Bindings
+-------------------------------------------
Required properties:
-- compatible : Should be "xlnx,spi-zynq".
+- compatible : Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6".
- reg : Physical base address and size of SPI registers map.
-- status : Status will be disabled in dtsi and enabled in required dts.
-- interrupt-parent : Must be core interrupt controller.
- interrupts : Property with a value describing the interrupt
number.
-- clocks : Clock phandles (see clock bindings for details).
+- interrupt-parent : Must be core interrupt controller
- clock-names : List of input clock names - "ref_clk", "pclk"
(See clock bindings for details).
+- clocks : Clock phandles (see clock bindings for details).
- spi-max-frequency : Maximum SPI clocking speed of device in Hz
+Optional properties:
+- num-cs : Number of chip selects used.
+ If a decoder is used, this will be the number of
+ chip selects after the decoder.
+- is-decoded-cs : Flag to indicate whether decoder is used or not.
+
Example:
- spi@e0006000 {
- compatible = "xlnx,zynq-spi";
- reg = <0xe0006000 0x1000>;
- status = "disabled";
- interrupt-parent = <&intc>;
- interrupts = <0 26 4>;
- clocks = <&clkc 25>, <&clkc 34>;
+ spi@e0007000 {
+ compatible = "xlnx,zynq-spi-r1p6";
clock-names = "ref_clk", "pclk";
- spi-max-frequency = <166666700>;
- #address-cells = <1>;
- #size-cells = <0>;
+ clocks = <&clkc 26>, <&clkc 35>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 49 4>;
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+ reg = <0xe0007000 0x1000>;
} ;
#include <phy.h>
#include <miiphy.h>
#include <watchdog.h>
+#include <asm/system.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sys_proto.h>
#define ZYNQ_GEM_NWCFG_MDCCLKDIV 0x000080000 /* Div pclk by 32, 80MHz */
#define ZYNQ_GEM_NWCFG_MDCCLKDIV2 0x0000c0000 /* Div pclk by 48, 120MHz */
-#define ZYNQ_GEM_NWCFG_INIT (ZYNQ_GEM_NWCFG_FDEN | \
+#ifdef CONFIG_ARM64
+# define ZYNQ_GEM_DBUS_WIDTH (1 << 21) /* 64 bit bus */
+#else
+# define ZYNQ_GEM_DBUS_WIDTH (0 << 21) /* 32 bit bus */
+#endif
+
+#define ZYNQ_GEM_NWCFG_INIT (ZYNQ_GEM_DBUS_WIDTH | \
+ ZYNQ_GEM_NWCFG_FDEN | \
ZYNQ_GEM_NWCFG_FSREM | \
ZYNQ_GEM_NWCFG_MDCCLKDIV)
u32 status;
};
-#define RX_BUF 3
+#define RX_BUF 32
/* Page table entries are set to 1MB, or multiples of 1MB
* (not < 1MB). driver uses less bd's so use 1MB bdspace.
*/
static inline int mdio_wait(struct eth_device *dev)
{
struct zynq_gem_regs *regs = (struct zynq_gem_regs *)dev->iobase;
- u32 timeout = 200;
+ u32 timeout = 20000;
/* Wait till MDIO interface is ready to accept a new transaction. */
while (--timeout) {
priv->tx_bd->addr = (u32)ptr;
priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) |
- ZYNQ_GEM_TXBUF_LAST_MASK;
+ ZYNQ_GEM_TXBUF_LAST_MASK |
+ ZYNQ_GEM_TXBUF_WRAP_MASK;
addr = (u32) ptr;
addr &= ~(ARCH_DMA_MINALIGN - 1);
size = roundup(len, ARCH_DMA_MINALIGN);
flush_dcache_range(addr, addr + size);
+
+ addr = (u32)priv->rxbuffers;
+ addr &= ~(ARCH_DMA_MINALIGN - 1);
+ size = roundup((RX_BUF * PKTSIZE_ALIGN), ARCH_DMA_MINALIGN);
+ flush_dcache_range(addr, addr + size);
barrier();
/* Start transmit */
if (frame_len) {
u32 addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK;
addr &= ~(ARCH_DMA_MINALIGN - 1);
- u32 size = roundup(frame_len, ARCH_DMA_MINALIGN);
- invalidate_dcache_range(addr, addr + size);
net_process_received_packet((u8 *)addr, frame_len);
priv->rxbuffers = memalign(ARCH_DMA_MINALIGN, RX_BUF * PKTSIZE_ALIGN);
memset(priv->rxbuffers, 0, RX_BUF * PKTSIZE_ALIGN);
- /* Align bd_space to 1MB */
+ /* Align bd_space to MMU_SECTION_SHIFT */
bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
mmu_set_region_dcache_behaviour((phys_addr_t)bd_space,
BD_SPACE, DCACHE_OFF);
250000000);
plat->speed_hz = plat->frequency / 2;
- debug("zynq_spi_ofdata_to_platdata: regs=%p max-frequency=%d\n",
+ debug("%s: regs=%p max-frequency=%d\n", __func__,
plat->regs, plat->frequency);
return 0;
};
static const struct udevice_id zynq_spi_ids[] = {
- { .compatible = "xlnx,zynq-spi" },
+ { .compatible = "xlnx,zynq-spi-r1p6" },
{ }
};
#define CONFIG_IDENT_STRING " Xilinx ZynqMP"
-#define CONFIG_SYS_TEXT_BASE 0x8000000
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
/* Flat Device Tree Definitions */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x400000)
/* Serial setup */
-#define CONFIG_ZYNQ_SERIAL_UART0
-#define CONFIG_ZYNQ_SERIAL
+#if defined(CONFIG_ZYNQMP_DCC)
+# define CONFIG_ARM_DCC
+# define CONFIG_CPU_ARMV8
+#else
+# if defined(CONFIG_ZYNQ_SERIAL_UART0) || defined(CONFIG_ZYNQ_SERIAL_UART1)
+# define CONFIG_ZYNQ_SERIAL
+# endif
+#endif
#define CONFIG_CONS_INDEX 0
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE \
{ 4800, 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_ZYNQ_SDHCI0
-
/* Command line configuration */
#define CONFIG_CMD_ENV
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_ELF
#define CONFIG_MP
+#define CONFIG_CMD_MII
+
+/* BOOTP options */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_MAY_FAIL
+#define CONFIG_BOOTP_SERVERIP
+
/* SPI */
#ifdef CONFIG_ZYNQ_SPI
# define CONFIG_SPI_FLASH_SST
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_MAXARGS 64
-#define CONFIG_ZYNQ_I2C0
-#define CONFIG_SYS_I2C_ZYNQ
+/* Ethernet driver */
+#if defined(CONFIG_ZYNQ_GEM0) || defined(CONFIG_ZYNQ_GEM1) || \
+ defined(CONFIG_ZYNQ_GEM2) || defined(CONFIG_ZYNQ_GEM3)
+# define CONFIG_NET_MULTI
+# define CONFIG_ZYNQ_GEM
+# define CONFIG_MII
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+# define CONFIG_PHYLIB
+# define CONFIG_PHY_MARVELL
+#endif
/* I2C */
#if defined(CONFIG_SYS_I2C_ZYNQ)
# define CONFIG_SYS_I2C_ZYNQ_SLAVE 0
#endif
-#define CONFIG_ZYNQMP_EEPROM
-
/* EEPROM */
#ifdef CONFIG_ZYNQMP_EEPROM
# define CONFIG_CMD_EEPROM
# define CONFIG_SYS_EEPROM_SIZE (64 * 1024)
#endif
+#ifdef CONFIG_AHCI
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_CMD_SCSI
+#endif
+
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
--- /dev/null
+/*
+ * Configuration for Xilinx ZynqMP emulation
+ * platforms. See zynqmp-common.h for ZynqMP
+ * common configs
+ *
+ * (C) Copyright 2014 - 2015 Xilinx, Inc.
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ *
+ * Based on Configuration for Versatile Express
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_ZYNQMP_EP_H
+#define __CONFIG_ZYNQMP_EP_H
+
+#define CONFIG_ZYNQ_SERIAL_UART0
+#define CONFIG_ZYNQ_SDHCI0
+#define CONFIG_ZYNQ_I2C0
+#define CONFIG_SYS_I2C_ZYNQ
+#define CONFIG_ZYNQ_EEPROM
+#define CONFIG_AHCI
+
+#include <configs/xilinx_zynqmp.h>
+
+#endif /* __CONFIG_ZYNQMP_EP_H */
# define CONFIG_ZYNQ_SDHCI0
# define CONFIG_ZYNQ_SPI
+#elif defined(CONFIG_ZC770_XM011)
+# define CONFIG_ZYNQ_SERIAL_UART1
+
#elif defined(CONFIG_ZC770_XM012)
# define CONFIG_ZYNQ_SERIAL_UART1
# undef CONFIG_SYS_NO_FLASH
projects / project / bcm63xx / u-boot.git / commitdiff