mediatek: add support for TP-Link Archer AX80v1(US/RU/CA)

This commit adds support for TP-Link Archer AX80v1(US/RU/CA).

Device specification
SoC Type:   MediaTek MT7986AV, Cortex-A53, 64-bit
RAM:        ESMT M15T4G16256 (512MB)
Flash:      ESMT F50L1G41LB (128 MB)
Ethernet:   MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet:   1x2.5Gbe (WAN/LAN 2.5Gbps), 4xGbE (WAN/LAN 1Gbps, LAN1, LAN2, LAN3)
WLAN 2g:    MediaTek MT7976GN
WLAN 5g:    MediaTek MT7976AN
LEDs:       1 red,1 green,1 blue status LEDs,

Buttons:    4 (Reset,ledswitch,wps,wlan),
USB ports:  1 (USB 3.0)
Power:      12 VDC, 3,3 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
            slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART)
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |
    +--- Don't connect

Installation (UART)
Place OpenWrt initramfs image on tftp server with IP 192.168.1.2

Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C'

Load and run OpenWrt initramfs image:

      tftpboot initramfs-kernel.bin
      bootm

!!Attention!! is very important! After entering OpenWrt, please set / update the environment variables:

fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data),8M(mali_data)"
fw_setenv tp_boot_idx 0

Run 'sysupgrade -n' with the sysupgrade OpenWrt image from console or Luci WebUI.

Recovery

Press Reset button and power on the router
Navigate to U-Boot recovery web server (192.168.1.1) and upload the OEM firmware

Stock layout

0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
0x000007300000-0x000007B00000 : "mali_data"

ubi0/ubi1 format
U-Boot at boot checks that all volumes are in place:

+-------------------------------+
| Volume Name: uboot   Vol ID: 0|
| Volume Name: kernel  Vol ID: 1|
| Volume Name: rootfs  Vol ID: 2|
+-------------------------------+
MAC addresses
+---------+-------------------+-----------+
| label   | 00:eb:xx:xx:xx:be | label     |
| LAN     | 00:eb:xx:xx:xx:be | label     |
| WAN     | 00:eb:xx:xx:xx:bf | label+1   |
| WLAN 2g | 00:eb:xx:xx:xx:be | label     |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1   |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file "default-mac".
OEM wireless eeprom is also there (file "MT7986_EEPROM.bin").

Signed-off-by: Sergey Shlukov <ichizakurain@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

9 files changed, 365 insertions, 0 deletions

diff --git a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic
index 18d6014f07..9654635bca 100644
--- a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic
+++ b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic
@@ -135,6 +135,9 @@ smartrg,sdg-8734)
 	local envdev=$(find_mmc_part "u-boot-env" "mmcblk0")
 	ubootenv_add_uci_config "$envdev" "0x0" "0x8000" "0x8000"
 	;;
+tplink,archer-ax80-v1)
+	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" "8"
+	;;
 ubnt,unifi-6-plus)
 	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x10000"
 	;;
diff --git a/target/linux/mediatek/dts/mt7986a-tplink-archer-ax80-v1.dts b/target/linux/mediatek/dts/mt7986a-tplink-archer-ax80-v1.dts
new file mode 100644
index 0000000000..841501c7cf
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7986a-tplink-archer-ax80-v1.dts
@@ -0,0 +1,332 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	compatible = "tplink,archer-ax80-v1", "mediatek,mt7986a";
+	model = "TP-Link Archer AX80V1";
+
+	aliases {
+		serial0 = &uart0;
+		led-boot = &led_B;
+		led-failsafe = &led_R;
+		led-running = &led_B;
+		led-upgrade = &led_G;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		reg = <0 0x40000000 0 0x20000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-ledswitch {
+			label = "ledswitch";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wifi {
+			label = "wlan";
+			linux,code = <KEY_WLAN>;
+			gpios = <&pio 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&auxadc {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		phy-handle = <&phy6>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1500000>;
+		reset-post-delay-us = <1000000>;
+
+		phy6: phy@6 {
+			compatible = "ethernet-phy-ieee802.3-c45";
+			reg = <6>;
+		};
+
+		switch@1f {
+			compatible = "mediatek,mt7531";
+			reg = <31>;
+			reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&pio>;
+			interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+				port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "2500base-x";
+					fixed-link {
+						speed = <2500>;
+						full-duplex;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	lp55231: led-controller@32 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lp55231";
+		reg = <0x32>;
+		status = "okay";
+		clock-mode = /bits/ 8 <1>;
+
+		led_B: led@0 {
+			chan-name = "B";
+			led-cur = /bits/ 8 <0x14>;
+			max-cur = /bits/ 8 <0x20>;
+			reg = <0>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led_G: led@3 {
+			chan-name = "G";
+			led-cur = /bits/ 8 <0x14>;
+			max-cur = /bits/ 8 <0x20>;
+			reg = <3>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led_R: led@6 {
+			chan-name = "R";
+			led-cur = /bits/ 8 <0x14>;
+			max-cur = /bits/ 8 <0x20>;
+			reg = <6>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+	};
+};
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+
+	spi_nand_flash: flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+
+		spi-max-frequency = <52000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		spi-cal-enable;
+		spi-cal-mode = "read-data";
+		spi-cal-datalen = <7>;
+		spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
+		spi-cal-addrlen = <5>;
+		spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+		partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot";
+				reg = <0x0 0x200000>;
+				read-only;
+			};
+
+			partition@200000 {
+				label = "u-boot-env";
+				reg = <0x200000 0x100000>;
+			};
+
+			partition@300000 {
+				label = "ubi0";
+				reg = <0x300000 0x3200000>;
+			};
+
+			partition@3500000 {
+				label = "ubi1";
+				reg = <0x3500000 0x3200000>;
+			};
+
+			partition@6700000 {
+				label = "userconfig";
+				reg = <0x6700000 0x800000>;
+			};
+
+			factory:partition@6f00000 {
+				label = "tp_data";
+				reg = <0x6f00000 0x400000>;
+			};
+
+			partition@7300000 {
+				label = "mali_data";
+				reg = <0x7300000 0x800000>;
+			};
+		};
+	};
+};
+
+&pio {
+	spi_flash_pins: spi-flash-pins-33-to-38 {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+		conf-pu {
+			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+		conf-pd {
+			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+			drive-strength = <8>;
+			mediatek,pull-down-adv = <0>; /* bias-disable */
+		};
+	};
+	wf_2g_5g_pins: wf_2g_5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			"WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 7eb6913310..861928d82d 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -134,6 +134,9 @@ mediatek_setup_interfaces()
 	wavlink,wl-wn586x3)
 		ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
 		;;
+	tplink,archer-ax80-v1)
+		ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" eth1
+		;;
 	tplink,re6000xd)
 		ucidef_set_interface_lan "lan1 lan2 eth1"
 		;;
@@ -182,6 +185,7 @@ mediatek_setup_macs()
 		wan_mac=$(macaddr_add "$lan_mac" 1)
 		;;
 	mercusys,mr90x-v1|\
+	tplink,archer-ax80-v1|\
 	tplink,re6000xd)
 		label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
 		lan_mac=$label_mac
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
index 34aacb9312..1d9db845db 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
@@ -27,6 +27,14 @@ case "$FIRMWARE" in
 		;;
 	esac
 	;;
+"mediatek/mt7986_eeprom_mt7976_dual.bin")
+	case "$board" in
+	tplink,archer-ax80-v1)
+		ln -sf /tmp/tp_data/MT7986_EEPROM.bin \
+			/lib/firmware/$FIRMWARE
+		;;
+	esac
+	;;
 *)
 	exit 1
 	;;
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index f027c306b1..b41e1bfce3 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -129,6 +129,7 @@ case "$board" in
 		[ "$PHYNBR" = "1" ] && macaddr_add $label_mac -2 > /sys${DEVPATH}/macaddress
 		;;
 	mercusys,mr90x-v1|\
+	tplink,archer-ax80-v1|\
 	tplink,re6000xd)
 		addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
 		[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
index 1474fad831..87e51a4429 100644
--- a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
@@ -14,6 +14,7 @@ preinit_mount_cfg_part() {
 	case $(board_name) in
 	mercusys,mr80x-v3|\
 	mercusys,mr90x-v1|\
+	tplink,archer-ax80-v1|\
 	tplink,re6000xd)
 		mount_ubi_part "tp_data"
 		;;
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
index 9d279898ac..936ed44ff9 100644
--- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
@@ -28,6 +28,7 @@ preinit_set_mac_address() {
 		ip link set dev eth1 address "$addr"
 		;;
 	mercusys,mr90x-v1|\
+	tplink,archer-ax80-v1|\
 	tplink,re6000xd)
 		addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
 		ip link set dev eth1 address "$(macaddr_add $addr 1)"
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index 5788b13978..7d204b9196 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -147,6 +147,7 @@ platform_do_upgrade() {
 		;;
 	mercusys,mr80x-v3|\
 	mercusys,mr90x-v1|\
+	tplink,archer-ax80-v1|\
 	tplink,re6000xd)
 		CI_UBIPART="ubi0"
 		nand_do_upgrade "$1"
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 93ba917d3a..1dc5698034 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -1685,6 +1685,20 @@ define Device/tenbay_wr3000k
 endef
 TARGET_DEVICES += tenbay_wr3000k
 
+define Device/tplink_archer-ax80-v1
+  DEVICE_VENDOR := TP-Link
+  DEVICE_MODEL := Archer AX80V1
+  DEVICE_DTS := mt7986a-tplink-archer-ax80-v1
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-leds-lp5523 kmod-usb3 kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 51200k
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += tplink_archer-ax80-v1
+
 define Device/tplink_re6000xd
   DEVICE_VENDOR := TP-Link
   DEVICE_MODEL := RE6000XD