openwrt/staging/dedeckeh.git
3 years agokernel: bump 5.10 to 5.10.40
Rui Salvaterra [Wed, 26 May 2021 11:58:06 +0000 (12:58 +0100)]
kernel: bump 5.10 to 5.10.40

Automatically refreshed:
generic/hack-5.10/902-debloat_proc.patch
generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
3 years agohostapd: support verbose build using V=sc
Felix Fietkau [Thu, 27 May 2021 10:16:52 +0000 (12:16 +0200)]
hostapd: support verbose build using V=sc

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agobase-files: generate network config with "device" options
Rafał Miłecki [Mon, 24 May 2021 14:45:06 +0000 (16:45 +0200)]
base-files: generate network config with "device" options

Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agohostapd: ACS: fix channel 100 frequency
David Bauer [Wed, 26 May 2021 20:23:35 +0000 (22:23 +0200)]
hostapd: ACS: fix channel 100 frequency

Channel 100 is a valid channel to choose for 80MHz operation. However,
it's assigned to 5500 MHz, not 5550MHz. In fact, there is no channel
assigned to this frequency.

Fix this obbvious typo to allow ACS to select channel 100 for 80 MHz
operation again.

Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agoath79: add missing v5.4 SPI chipselect patch
David Bauer [Wed, 26 May 2021 09:37:42 +0000 (11:37 +0200)]
ath79: add missing v5.4 SPI chipselect patch

The patch was not applied to the v5.4 target, thus breaking Kernel 5.4
on devices with multiple flash chips attache to the SPI bus.

Fixes commit bd54e739541b ("ath79: set number of chipselect lines")

Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agokernel: fix AutoLoad parameter for uleds module
Evgeny Kolesnikov [Tue, 25 May 2021 14:38:33 +0000 (16:38 +0200)]
kernel: fix AutoLoad parameter for uleds module

The name of the module is 'uleds', not 'leds-uleds'.

Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agoramips: add support for JCG Q20
Chukun Pan [Sun, 16 May 2021 12:10:05 +0000 (20:10 +0800)]
ramips: add support for JCG Q20

JCG Q20 is an AX 1800M router.

Hardware specs:
  SoC: MediaTek MT7621AT
  Flash: Winbond W29N01HV 128 MiB
  RAM: Winbond W632GU6NB-11 256 MiB
  WiFi: MT7915 2.4/5 GHz 2T2R
  Ethernet: 10/100/1000 Mbps x3
  LED: Status (red / blue)
  Button: Reset, WPS
  Power: DC 12V,1A

Flash instructions:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings.

MAC addresses map:
  0x00004 *:3e wlan2g/wlan5g
  0x3fff4 *:3c lan/label
  0x3fffa *:3c wan

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
3 years agoramips: add support for cudy WR2100
Leon M. George [Thu, 24 Dec 2020 10:32:47 +0000 (11:32 +0100)]
ramips: add support for cudy WR2100

Specifications

  SoC:       MT7621
  CPU:       880 MHz
  Flash:     16 MiB
  RAM:       128 MiB
  WLAN:      2.4 GHz b/g/n, 5 GHz a/n/ac
             MT7603E / MT7615E
  Ethernet:  5x Gbit ports

Installation

There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
   The router will request 'recovery.bin' from a TFTP server at
   192.168.1.88.

Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.

R4 & R5 need to be shorted (0-100Ω) for the UART to work.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[remove non-required switch-port node - remove trgmii phy-mode]
Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agoramips: add support for TP-Link Archer C6U v1 (EU)
Georgi Vlaev [Fri, 31 Jul 2020 11:02:21 +0000 (14:02 +0300)]
ramips: add support for TP-Link Archer C6U v1 (EU)

This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).

Specifications:
--------------

* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.

Installation:
------------

Install the OpenWrt factory image for C6U is from the
TP-Link web interface.

1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.

Recovery to stock firmware:
--------------------------

The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:

1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.

2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.

MAC addresses:
-------------

OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN

Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
3 years agoramips: add support for TP-Link Archer A6 v3
Vinay Patil [Mon, 19 Apr 2021 01:22:51 +0000 (06:52 +0530)]
ramips: add support for TP-Link Archer A6 v3

The patch adds support for the TP-Link Archer A6 v3
The router is sold in US and India with FCC ID TE7A6V3

Specification
-------------
MediaTek MT7621 SOC
RAM:         128MB DDR3
SPI Flash:   W25Q128 (16MB)
Ethernet:    MT7530 5x 1000Base-T
WiFi 5GHz:   Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1

Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports:    LAN4 LAN3 LAN2 LAN1 WAN
             _______________________
             |                     |
Serial Pins: |   VCC GND TXD RXD   |
             |_____________________|

LEDs:         Power Wifi2G Wifi5G LAN WAN

Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin

How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.

TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.

Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated from serial console only.
Press 'x' while u-boot is starting
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1

Thanks to: Frankis for Randmon MAC address fix.

Signed-off-by: Vinay Patil <post2vinay@gmail.com>
[remove superfluous factory image definition, whitespacing]
Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agomac80211: sync nl80211.h with upstream and backport a WPA3 related commit
Felix Fietkau [Wed, 26 May 2021 18:00:14 +0000 (20:00 +0200)]
mac80211: sync nl80211.h with upstream and backport a WPA3 related commit

Fixes compatibility issues with the latest hostapd update

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agoimx6: image: drop BOOT_SCRIPT and fix DEVICE_NAME
Piotr Dymacz [Wed, 26 May 2021 10:36:30 +0000 (12:36 +0200)]
imx6: image: drop BOOT_SCRIPT and fix DEVICE_NAME

This fixes Gateworks Ventana 'DEVICE_NAME' variable which value wasn't
adjusted during migration to common 'vendor_model' image naming scheme
(fixes: FS#3825).

Furthermore, drop unused 'Build/boot-scr' recipe, get rid of redundant
'BOOT_SCRIPT' variable (use already provided 'DEVICE_NAME' instead) and
drop custom 'DEVICE_NAME' variable from SolidRun CuBox-i image recipe
(use default one instead).

Fixes: cbc8bcfbaa ("imx6: image: use vendor_model scheme")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agomac80211: add more HE capabilities
Felix Fietkau [Tue, 25 May 2021 09:10:51 +0000 (11:10 +0200)]
mac80211: add more HE capabilities

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agomac80211: fix center freq selection for 6 GHz
Felix Fietkau [Tue, 25 May 2021 08:57:01 +0000 (10:57 +0200)]
mac80211: fix center freq selection for 6 GHz

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: fix adding back stations after a missed deauth/disassoc
Felix Fietkau [Tue, 25 May 2021 08:50:16 +0000 (10:50 +0200)]
hostapd: fix adding back stations after a missed deauth/disassoc

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: update to version 2021-05-21
Felix Fietkau [Mon, 24 May 2021 17:24:37 +0000 (19:24 +0200)]
hostapd: update to version 2021-05-21

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agomac80211: set hostapd op_class for 6 GHz
Felix Fietkau [Mon, 24 May 2021 16:45:57 +0000 (18:45 +0200)]
mac80211: set hostapd op_class for 6 GHz

This is needed to disambiguate it from 5 GHz channels

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agomac80211: rework default config script
Felix Fietkau [Mon, 24 May 2021 12:56:02 +0000 (14:56 +0200)]
mac80211: rework default config script

Emit the new band option instead of hwmode
Support 6 GHz band and HE options

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agomac80211: make use of the new 'band' option
Felix Fietkau [Mon, 24 May 2021 12:55:01 +0000 (14:55 +0200)]
mac80211: make use of the new 'band' option

Use it to look up frequencies only in the configured band to better deal
with channel number overlap

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agomac80211: add 6 GHz support to mac80211_hwsim
Felix Fietkau [Mon, 24 May 2021 09:52:40 +0000 (11:52 +0200)]
mac80211: add 6 GHz support to mac80211_hwsim

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agowireless-regdb: update to version 2021.04.21
Felix Fietkau [Fri, 21 May 2021 12:29:31 +0000 (14:29 +0200)]
wireless-regdb: update to version 2021.04.21

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agoiw: update to 8fab0c9e
Andre Heider [Tue, 18 May 2021 05:13:50 +0000 (07:13 +0200)]
iw: update to 8fab0c9e

This fixes `iw dev wlan0-mesh station dump`.

8fab0c9 iw: fix ftm_request missing arguments segfault
e816fbc iw: fix mgmt dump missing arguments segfault
5d9d1b8 iw: Fix timestamp output on 32-bit architectures
4b25ae3 iw: fix pointer arithmetic in __print_he_capa
c3df363 iw: add option to print human readable event time
cd64525 iw: print ctrl port tx status event
0ba98b9 iw: use correct type in policy check for mesh
9e38dee iw: scan: fixup HE caps whitespace
17e8564 iw: scan: parse HE capabilities
5735e58 iw: util: factor out HE capability parser
6d8d507 iw: scan: add extension tag parsing
b4e1ec4 man: update wikipage URL, reformat SEE ALSO section
c56036a iw: enable 80MHz support for 6GHz band 11s mesh
fa72728 iw: handle positive error codes gracefully
7ba9093 iw: scan: add flag for scanning colocated ap
5ec60ed iw: Add 'coloc' and 'flush' options to sched_scan
f8ade75 iw: update wikipage URL
b6f2dac iw: Add support for specifying the 160MHz bandwidth when setting the channel/frequency

Signed-off-by: Andre Heider <a.heider@gmail.com>
3 years agohostapd: add support for configuring rts threshold
Felix Fietkau [Tue, 18 May 2021 15:46:01 +0000 (17:46 +0200)]
hostapd: add support for configuring rts threshold

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: fix max_oper_chwidth setting for HE
Felix Fietkau [Tue, 18 May 2021 17:08:28 +0000 (19:08 +0200)]
hostapd: fix max_oper_chwidth setting for HE

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: add additional radius options
John Crispin [Tue, 18 May 2021 15:53:45 +0000 (17:53 +0200)]
hostapd: add additional radius options

- add functionality to configure RADIUS NAS-Id and Operator-Name
- add functionality to configure RADIUS accounting interval
- enable RADIUS "Chargeable User Identity"

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: add extra options for hotspot 2.0 / interworking
Felix Fietkau [Tue, 18 May 2021 15:06:48 +0000 (17:06 +0200)]
hostapd: add extra options for hotspot 2.0 / interworking

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: report radar detected events via ubus
Felix Fietkau [Tue, 18 May 2021 14:08:59 +0000 (16:08 +0200)]
hostapd: report radar detected events via ubus

Events are reported on all BSS interfaces

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: improve channel switch support
Felix Fietkau [Tue, 18 May 2021 13:58:03 +0000 (15:58 +0200)]
hostapd: improve channel switch support

Instead of requiring the user to call it on each BSS individually,
run it on all BSSs internally.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: add missing inline stubs for ubus vlan event support
Felix Fietkau [Tue, 18 May 2021 13:51:00 +0000 (15:51 +0200)]
hostapd: add missing inline stubs for ubus vlan event support

Only used when building without ubus support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: fix civic location option
John Crispin [Tue, 6 Apr 2021 11:24:43 +0000 (13:24 +0200)]
hostapd: fix civic location option

Signed-off-by: John Crispin <john@phrozen.org>
3 years agonetifd: update to the latest master
Rafał Miłecki [Wed, 26 May 2021 05:54:19 +0000 (07:54 +0200)]
netifd: update to the latest master

899c2a4 interface: support "device" attribute and deprecate "ifname"
62e3cb5 scripts/netifd-wireless.sh: add support for specifying the operating band

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agoopkg: use $(PROJECT_GIT), $(AUTORELEASE) and SPDX
Nick Hainke [Wed, 19 May 2021 20:39:35 +0000 (22:39 +0200)]
opkg: use $(PROJECT_GIT), $(AUTORELEASE) and SPDX

1) Use SPDX license headers to be machine readable.
2) Update copyright to 2021.
3) Use $(PROJECT_GIT) instead of manually specifying the git url.
4) Use $(AUTORELEASE) to automatically set the correct PKG_RELEASE.

Signed-off-by: Nick Hainke <vincent@systemli.org>
3 years agobuild: fix regression for kernels < 5.10
Sebastian Kemper [Tue, 13 Apr 2021 12:22:20 +0000 (14:22 +0200)]
build: fix regression for kernels < 5.10

This fixes a regression introduced with commit
5ed1e5140a80558ab47fd70410ae3242bed5becf ("build: build kernel image
before building modules/packages").

Before this commit the make target would always include "modules",
resulting in a MODPOST and a complete Module.symvers file. Since this
commit a MODPOST of the kernel modules is not guaranteed for kernels <
5.10. This results in some broken SDKs in which external packages that
depend on exported symbols from kernel modules fail to compile.

Adding "modules" back to the calls to the CompileImage defines fixes the
regression. For kernels > 5.10 this is not needed, but it doesn't cause
any harm either.

Tested with kernels 5.4.x and 5.10.x.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
3 years agokernel: fix a perf build error
Felix Fietkau [Tue, 25 May 2021 16:12:41 +0000 (18:12 +0200)]
kernel: fix a perf build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agobusybox: mention SRV support in help message
Paul Spooren [Thu, 20 May 2021 10:08:10 +0000 (12:08 +0200)]
busybox: mention SRV support in help message

The SRV was added some time ago and should be mentioned in the short
help message to avoid confusion about missing features.

Signed-off-by: Paul Spooren <mail@aparcar.org>
3 years agonat46: fix memory leak
Hans Dedecker [Mon, 24 May 2021 10:59:29 +0000 (12:59 +0200)]
nat46: fix memory leak

0d5860d fix memory leak in nat46_netdev_destroy().The netdev is forgotten to free in nat46_netdev_destroy function (#26)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
3 years agobase-files: fix configuration generation of network if "bridge" exists
INAGAKI Hiroshi [Sun, 23 May 2021 11:30:58 +0000 (20:30 +0900)]
base-files: fix configuration generation of network if "bridge" exists

After the commit 43fc720657c6e3b30c6ed89d7227ee6e646c158b
("base-files: generate "device UCI type section for bridge"), the wrong
network configuration is generated for the devices that already have the
bridge device section for VLAN, such as the devices in realtek target.

As a result, the bridge device by additional "device" section is
specified to the "ports" option in the "bridge-vlan" section and netifd
shuts down the switch and the ethernet when the network service started.

Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rmilecki: use $ports for generate_bridge_vlan argument]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agobase-files: support setting bridge MAC address
Rafał Miłecki [Mon, 24 May 2021 05:46:12 +0000 (07:46 +0200)]
base-files: support setting bridge MAC address

Fixes: 43fc720657c6 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agotreewide: Mark packages nonshared if they depend on @TARGET_
Hauke Mehrtens [Sun, 2 May 2021 22:35:38 +0000 (00:35 +0200)]
treewide: Mark packages nonshared if they depend on @TARGET_

This marks all packages which depend on a target with @TARGET nonshared.
If they are not marked nonshared they would be build by the SDK build
and if this happens with a different SDK, then the SDK from the target
the package depends on, the package would not be added to the index.

This should fix the image builder for some of these packages.

This should fix the image builder at least for bcm27xx/bcm2710 and
bcm4908/generic.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3 years agomediatek: update mtd parser patches
Hauke Mehrtens [Sun, 18 Apr 2021 19:51:00 +0000 (21:51 +0200)]
mediatek: update mtd parser patches

This updates the patches to match the versions included in the mtd
subsystem for the next Linux kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3 years agokernel: backport "mvmdio avoid error message for optional IRQ"
Daniel González Cabanelas [Fri, 23 Apr 2021 15:33:32 +0000 (17:33 +0200)]
kernel: backport "mvmdio avoid error message for optional IRQ"

Rid of kernel error message:
  [    0.780828] orion-mdio d0072004.mdio: IRQ index 0 not found

on Marvell targets backporting the kernel commit fa2632f74e57

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
3 years agogeneric: mt7530: fix EEE patch
DENG Qingfang [Fri, 7 May 2021 04:36:03 +0000 (12:36 +0800)]
generic: mt7530: fix EEE patch

The higher 16-bit of EEE register was overwritten by mistake, fix that.

Fixes: 5b9ba4a93e83 ("generic: mt7530: support adjusting EEE")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
3 years agoccache: Build with ENABLE_DOCUMENTATION=OFF
David Adair [Fri, 14 May 2021 23:04:27 +0000 (16:04 -0700)]
ccache: Build with ENABLE_DOCUMENTATION=OFF

This adjusts the Makefile to use the new option to turn off the
doc builds. It will not cause any problems except a warning
about unused options if combined with a ccache source missing
the upstream patch.

Since a config setting is required to re-enable the doc build this
is equivalent to unconditionally disabling the docs if the config
setting is not created.

Signed-off-by: David Adair <djabhead@aol.com>
3 years agomac80211: fix ATH_REG_DYNAMIC_USER_REG_HINTS
Robert Marko [Sun, 16 May 2021 16:06:58 +0000 (18:06 +0200)]
mac80211: fix ATH_REG_DYNAMIC_USER_REG_HINTS

ATH_REG_DYNAMIC_USER_REG_HINTS is currently not being set as mac80211
tries to set it as m which is not possible as its boolean only.

Since its used alongside user regulatory, move it to USER_REGD.

This is required for ath11k to accept regulatory changes, otherwise
it wont accept any changes and will simply force US.

Signed-off-by: Robert Marko <robimarko@gmail.com>
3 years agoprereq-build: g++ formatting and consistency fixes
Karl Palsson [Mon, 17 May 2021 00:38:03 +0000 (00:38 +0000)]
prereq-build: g++ formatting and consistency fixes

Remove \n that mangles output, and fix inconsistent version name check.

Example before:

Build dependency: Please install the GNU C++ Compiler (g++) 6 or later
Build dependency: \nPlease reinstall the GNU C++ Compiler (4.8 or later) - it appears to be broken
Build dependency: Please install ncurses. (Missing libncurses.so or ncurses.h)

Signed-off-by: Karl Palsson <karlp@tweak.net.au>
3 years agomvebu: 5.10 fix DVFS caused random boot crashes
Robert Marko [Wed, 19 May 2021 11:02:31 +0000 (13:02 +0200)]
mvebu: 5.10 fix DVFS caused random boot crashes

5.10.37 and 5.4.119 introduced a lot of DVFS changes for Armada 37xx from 5.13 kernel.

Unfortunately commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/cpufreq/armada-37xx-cpufreq.c?h=v5.10.37&id=a13b110e7c9e0dc2edcc7a19d4255fc88abd83cc

This patch actually corrects the things so that 1 or 1.2GHz models would actually get scaled to their native frequency.

However, due to a AVS setting voltages too low this will cause random crashes on 1.2GHz models.

So, until a new safe for everybody voltage is agreed on
lets revert the patch.

Fixes: d337731 ("kernel: bump 5.10 to 5.10.37")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
3 years agokernel-defaults: fix external kernel build when user_headers is missing
Matt Merhar [Fri, 26 Feb 2021 04:28:53 +0000 (23:28 -0500)]
kernel-defaults: fix external kernel build when user_headers is missing

Use an 'if' so the absence of $(LINUX_DIR)/user_headers doesn't make the
line evaluate to false and cause the build to fail.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
3 years agokexec-tools: add patch to fix issue with appended DTB and zImage on ARM
Alexander Egorenkov [Sat, 17 Apr 2021 07:50:39 +0000 (09:50 +0200)]
kexec-tools: add patch to fix issue with appended DTB and zImage on ARM

This patch fixes a recently found problem when a zImage passed to
kexec-tools contains an appended DTB. In that case kexec boot fails because
the decompressor wrongly tries to use the non-existing appended DTB instaed
of the one passed in the register r2.

- http://lists.infradead.org/pipermail/kexec/2021-April/022353.html

Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
3 years agobinutils: update to 2.35.2
Konstantin Demin [Fri, 23 Apr 2021 06:49:55 +0000 (09:49 +0300)]
binutils: update to 2.35.2

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
3 years agokernel: limit crypto-hw-talitos to the mpc85xx and layerscape
Aleksander Jan Bajkowski [Thu, 29 Apr 2021 21:02:53 +0000 (23:02 +0200)]
kernel: limit crypto-hw-talitos to the mpc85xx and layerscape

CONFIG_CRYPTO_DEV_TALITOS depends on FSL_SOC. This driver only makes sense
on Freescale(NXP) SoCs.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
3 years agokernel: limit crypto-hw-geode to the x86/geode
Aleksander Jan Bajkowski [Thu, 29 Apr 2021 20:55:47 +0000 (22:55 +0200)]
kernel: limit crypto-hw-geode to the x86/geode

CONFIG_CRYPTO_DEV_GEODE depends on X86_32. This driver only makes sense
on X86\geode.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
3 years agokernel: crypto: drop kmod-crypto-pcompress
Aleksander Jan Bajkowski [Sun, 2 May 2021 09:27:23 +0000 (11:27 +0200)]
kernel: crypto: drop kmod-crypto-pcompress

CONFIG_CRYPTO_PCOMP and CONFIG_CRYPTO_PCOMP2 have been removed in upstream commit[1].
This symbol doesn't exist since kernel 4.6 and this package is empty.

1. [ crypto: compress - remove unused pcomp interface ]
(https://github.com/torvalds/linux/commit/110492183c4b8f572b16fce096b9d78e2da30baf)

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
3 years agokernel: crypto: drop kmod-crypto-wq
Aleksander Jan Bajkowski [Sun, 2 May 2021 09:25:46 +0000 (11:25 +0200)]
kernel: crypto: drop kmod-crypto-wq

CONFIG_CRYPTO_WORKQUEUE was removed in upstream commit[1]. This symbol doesn't
exist since kernel 5.3 and this package is empty.

1. [ crypto: cryptd - move kcrypto_wq into cryptd ]
(https://github.com/torvalds/linux/commit/3e56e168638b3e7147902c3b7257a57ea573a30e)

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
3 years agowolfssl: add support for OpenVPN
Ivan Pavlov [Wed, 5 May 2021 15:23:19 +0000 (18:23 +0300)]
wolfssl: add support for OpenVPN

Support for wolfSSL has been upstreamed to the master OpenVPN branch
in f6dca235ae560597a0763f0c98fcc9130b80ccf4, so we can use wolfSSL
directly in OpenVPN. So no more needed differnt SSL engine for OpenVPN
in systems based on wolfSSL library
Compiled && tested on ramips/mt7620, ramips/mt7621

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
3 years agofakeroot: Alpine linux libc.musl build error fix
Ruslan Isaev [Mon, 10 May 2021 14:56:59 +0000 (14:56 +0000)]
fakeroot: Alpine linux libc.musl build error fix

Prevent build error on Alpine Linux host:
libfakeroot.c error: conflicting types for 'id_t'
Error relocating openwrt/staging_dir/host/lib/libfakeroot.so: SEND_GET_XATTR: symbol not found

Signed-off-by: Ruslan Isaev <legale.legale@gmail.com>
3 years agoapm821xx: MR24: Change default config of WLAN LED
Tan Zien [Fri, 14 May 2021 16:34:11 +0000 (00:34 +0800)]
apm821xx: MR24: Change default config of WLAN LED

The previous config will only show 2.4G radio activity status

This change mr24:green:wifi4 and mr24:green:wifi2 to
show 2.4G and 5G radio on and off status

change mr24:green:wifi3 and mr24:green:wifi1 to
show 2.4G and 5G radio activity status

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
3 years agokernel: add kmod-input-leds
Anderson McKinley [Wed, 19 May 2021 23:38:21 +0000 (23:38 +0000)]
kernel: add kmod-input-leds

Adds support for LEDs on input devices. Useful for example on x86 laptops-
allows re-purposing num/caps/scroll lock LEDs.

Signed-off-by: Anderson McKinley <coyoso@tuta.io>
3 years agoipq806x: fix warning about tsens debugfs already registered
Ansuel Smith [Tue, 11 May 2021 22:20:49 +0000 (00:20 +0200)]
ipq806x: fix warning about tsens debugfs already registered

Backport a pending patch already reviewed that fix some warning about tsens debugs already registered.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
3 years agoipq806x: reduce pci IO space to 64k
Ansuel Smith [Tue, 11 May 2021 22:13:04 +0000 (00:13 +0200)]
ipq806x: reduce pci IO space to 64k

With some talk with the ARM maintainer, it was notice that enlarging the limit
to the current value is VERY wrong and clash with other memory.
A better solution would be to reduce the IO space from 1MB to 64K as probably
it's a long lasting typo and even x86 arch doesn't have a IO space that big.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
3 years agokernel: bump 5.4 to 5.4.121
John Audia [Sat, 22 May 2021 10:50:01 +0000 (06:50 -0400)]
kernel: bump 5.4 to 5.4.121

All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
3 years agokernel: bump 5.4 to 5.4.120
John Audia [Fri, 21 May 2021 10:29:01 +0000 (06:29 -0400)]
kernel: bump 5.4 to 5.4.120

Removed upstreamed:
  generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Note that since I rebased the previous commit, I removed my Run-tested line
although I confirm building the image successfully.

Signed-off-by: John Audia <graysky@archlinux.us>
3 years agokernel: bump 5.4 to 5.4.119
John Audia [Fri, 14 May 2021 09:05:17 +0000 (05:05 -0400)]
kernel: bump 5.4 to 5.4.119

Removed upstreamed:
  generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
  bcm63xx/patches-5.4/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch*

Removed/code was included upstream and therefore redundant:
  ramips/patches-5.4/999-fix-pci-init-mt7620.patch

All other patches automatically rebased.

* update_kernel.sh did not flag this yet it was included in 5.4.119[1], as a
  result of the rebase, I removed my testing lines since I did not go back to
  test built or to run test 5.4.119 with the removed patch present.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.119&id=e5b3e69eb36ac1178a7a2392616fd29afd288c4e

Signed-off-by: John Audia <graysky@archlinux.us>
3 years agokernel: bump 5.4 to 5.4.118
John Audia [Tue, 11 May 2021 15:50:27 +0000 (11:50 -0400)]
kernel: bump 5.4 to 5.4.118

Manually rebased:
  ath79/patches-5.4/0033-spi-ath79-drop-pdata-support.patch

Removed uneeded patch:
  ath79/patches-5.4/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
3 years agokernel: bump 5.10 to 5.10.39
Kevin Darbyshire-Bryant [Sat, 22 May 2021 12:10:57 +0000 (13:10 +0100)]
kernel: bump 5.10 to 5.10.39

Automatically refreshed:

generic/pending-5.10/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
3 years agokernel: bump 5.10 to 5.10.38
Rui Salvaterra [Wed, 19 May 2021 11:14:40 +0000 (12:14 +0100)]
kernel: bump 5.10 to 5.10.38

Automatically refreshed:
apm821xx/patches-5.10/802-usb-xhci-force-msi-renesas-xhci.patch
generic/backport-5.10/610-v5.13-31-net-ethernet-mtk_eth_soc-fix-parsing-packets-in-GDM.patch
generic/backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch
generic/backport-5.10/610-v5.13-33-net-ethernet-mtk_eth_soc-add-flow-offloading-support.patch
generic/hack-5.10/204-module_strip.patch
generic/hack-5.10/911-kobject_add_broadcast_uevent.patch
ipq806x/patches-5.10/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch
ipq806x/patches-5.10/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch

Deleted (reverse-appliable):
generic/backport-5.10/610-v5.13-37-net-ethernet-mtk_eth_soc-fix-RX-VLAN-offload.patch
ipq806x/patches-5.10/106-5.13-net-stmmac-Set-FIFO-sizes-for-ipq806x.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
3 years agohostapd: wolfssl: add RNG to EC key
David Bauer [Wed, 5 May 2021 23:53:49 +0000 (01:53 +0200)]
hostapd: wolfssl: add RNG to EC key

Since upstream commit 6467de5a8840 ("Randomize z ordinates in
scalar mult when timing resistant") WolfSSL requires a RNG for
the EC key when built hardened which is the default.

Set the RNG for the EC key to fix connections for OWE clients.

Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agowolfssl: always export wc_ecc_set_rng
David Bauer [Wed, 5 May 2021 23:48:04 +0000 (01:48 +0200)]
wolfssl: always export wc_ecc_set_rng

Since commit 6467de5a8840 ("Randomize z ordinates in scalar
mult when timing resistant") wolfssl requires a RNG for an EC
key when the hardened built option is selected.

wc_ecc_set_rng is only available when built hardened, so there
is no safe way to install the RNG to the key regardless whether
or not wolfssl is compiled hardened.

Always export wc_ecc_set_rng so tools such as hostapd can install
RNG regardless of the built settings for wolfssl.

Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agobusybox: nslookup applet link with resolv if use glibc
Chen Minqiang [Thu, 20 May 2021 08:34:28 +0000 (16:34 +0800)]
busybox: nslookup applet link with resolv if use glibc

This fixed b36b8b6929c6d6b17edddfb4597cf6a26a991ed0
("busybox: remove nslookup_lede/openwrt.patch")

It is likely dropped by mistake, This add back the changes

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
3 years agogrub2: disable liblzma dependency
Dirk Neukirchen [Thu, 20 May 2021 08:39:35 +0000 (10:39 +0200)]
grub2: disable liblzma dependency

Florian Ekert reported:

"I have build a fresh master branch recently, Since your last change [1]
on grub2, I have now a new dependency on liblzma for the install package
grub2-editenv.

root@st-dev-07 /usr/lib # ldd /root/grub-editenv
       /lib/ld-musl-x86_64.so.1 (0x7f684b088000)
       liblzma.so.5 => /usr/lib/liblzma.so.5 (0x7f684b06d000)
       libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7f684b059000)
       libc.so => /lib/ld-musl-x86_64.so.1 (0x7f684b088000)

This was not the case before your update.

root@st-dev-07 /usr/sbin # ldd /usr/sbin/grub-editenv
       /lib/ld-musl-x86_64.so.1 (0x7fd970176000)
       libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7fd970162000)
       libc.so => /lib/ld-musl-x86_64.so.1 (0x7fd970176000)

My build complains that it cannot satisfy the runtime package dependency
for grub2-editenv.

install -d -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin
install -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/grub-editenv /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin/
find /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv -name 'CVS' -o -name '.svn' -o -name '.#*' -o -name '*~'| xargs -r rm -rf
Package grub2-editenv is missing dependencies for the following libraries:
liblzma.so.5
make[2]: *** [Makefile:166: /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/bin/APOS/feckert/master/master-Maggie-455-ga5edc0e8e/x86_64/targets/x86/64/packages/grub2-editenv_2.06~rc1-1_x86_64.ipk] Error 1
make[2]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/package/boot/grub2'
time: package/boot/grub2/pc/compile#78.64#9.79#83.88
   ERROR: package/boot/grub2 failed to build (build variant: pc).
make[1]: *** [package/Makefile:116: package/boot/grub2/compile] Error 1
make[1]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt'
make: *** [/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/include/toplevel.mk:230: package/boot/grub2/compile] Error 2

If I add the following changes to the package all works as expected.

<snip>
-  DEPENDS:=@TARGET_x86
+  DEPENDS:=@TARGET_x86 +liblzma
  VARIANT:=pc
endef

This is a hotfix but I dont´t think this is the final solution, because lzma is provided by the package xz.
And This is maintained in the package feed [not the core]"

Dirk stated & offered his patch to disable liblzma and thus resolve the
'out of core dependency' problem:

"LZMA is used in mkimage.c
disabling it prints
Without liblzma (no support for XZ-compressed mips images) (explicitly disabled)
(see configure.ac)

liblzma is autodetected so this issue was present but hidden somehow

[unsure: grep/image generation does not use grub with that option]
OpenWrt does not use that feature currently

[!] some scripts and examples use --compression=xz or -C xz and those will break

grub has an internal xzlib for different "lzma" functionality
(ext. LIBLZMA from XZ (GRUB_COMPRESSION_XZ) vs. GRUB_COMPRESSION_LZMA)"

Hopefully fixes e74d81ece2e2932a4f370d8e6d180061a6a2c229 and doesn't
break anything else.

Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
[include Florian's description of how problem 1st encountered]
[bump package release]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
3 years agouboot-envtools: support uci-default config also per subtargets
Piotr Dymacz [Thu, 1 Apr 2021 22:52:56 +0000 (00:52 +0200)]
uboot-envtools: support uci-default config also per subtargets

The current version of 'uboot-envtools' package generates dedicated
uci-default file only per target. This change makes it possible to
use subtarget-specific files, with name pattern: 'target_subtarget'
(example: 'ath79_nand'). The subtarget-specific files will take
precedence over target-specific one.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agoimx6: image: cleanup variables order within device's defines
Piotr Dymacz [Sun, 28 Mar 2021 13:31:12 +0000 (15:31 +0200)]
imx6: image: cleanup variables order within device's defines

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agoimx6: image: keep devices in alphabetical order
Piotr Dymacz [Sun, 28 Mar 2021 13:23:47 +0000 (15:23 +0200)]
imx6: image: keep devices in alphabetical order

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agouboot-imx6: update BUILD_DEVICES values
Piotr Dymacz [Sun, 28 Mar 2021 23:02:52 +0000 (01:02 +0200)]
uboot-imx6: update BUILD_DEVICES values

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agouboot-imx6: drop 'HIDDEN' flag from 'mx6cuboxi' define
Piotr Dymacz [Sun, 28 Mar 2021 23:02:05 +0000 (01:02 +0200)]
uboot-imx6: drop 'HIDDEN' flag from 'mx6cuboxi' define

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agoimx6: image: use vendor_model scheme
Piotr Dymacz [Sat, 9 Jan 2021 15:47:41 +0000 (16:47 +0100)]
imx6: image: use vendor_model scheme

This switches device names to the common 'vendor_model' approach as in
most of other targets in OpenWrt.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agoimx6: image: cleanup image recipes
Piotr Dymacz [Fri, 8 Jan 2021 11:18:32 +0000 (12:18 +0100)]
imx6: image: cleanup image recipes

- drop unused 'UBOOT' variable from 'Device/apalis' recipe
- fix 'KERNEL_SUFFIX' for 'Device/cubox-i' (should be '-zImage')
- drop redundant 'DEVICE_{VENDOR,MODEL}' from 'Device/ventana-large'
- other, minor fixes

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agoimx6: rename Freescale to NXP in BOARDNAME and profiles
Piotr Dymacz [Tue, 9 Mar 2021 12:41:27 +0000 (13:41 +0100)]
imx6: rename Freescale to NXP in BOARDNAME and profiles

Freescale no longer exists, it was acquired by NXP in 2015.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
3 years agofirmware-utils: fix coverity zytrx.c resource leak
Kevin Darbyshire-Bryant [Sun, 16 May 2021 10:46:32 +0000 (11:46 +0100)]
firmware-utils: fix coverity zytrx.c resource leak

fix coverity resource leak warning:

     *len = stat.st_size;
     mapped = mmap(NULL, stat.st_size, PROT_READ, MAP_SHARED, fd, 0);
     if (close(fd) < 0)
CID 1484880:  Resource leaks  (RESOURCE_LEAK)
Variable "mapped" going out of scope leaks the storage it points to.
     return NULL;
     return mapped;
    }

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
3 years agoRevert "base-files: migrate old UCI network bridge ports syntax"
Rafał Miłecki [Thu, 20 May 2021 10:23:55 +0000 (12:23 +0200)]
Revert "base-files: migrate old UCI network bridge ports syntax"

This reverts commit f716c30241d5fd9d821560f58d0af0c3ffe78600.

Migrating everyone to the new syntax could break downgrades. We may
reintroduce it way later if needed.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agonetifd: update to the latest master
Rafał Miłecki [Thu, 20 May 2021 10:22:12 +0000 (12:22 +0200)]
netifd: update to the latest master

config: fix ifname->ports compat rename

Fixes: 829b5c2ba32f ("netifd: update to the latest version")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agobase-files: generate bridge device sections with br- name prefix
Rafał Miłecki [Thu, 20 May 2021 08:32:18 +0000 (10:32 +0200)]
base-files: generate bridge device sections with br- name prefix

Missing br- prefix could result in name conflict between DSA port
interface and bridge interface. Some devices with just one LAN port use
"lan" interface name for DSA port. Trying to create bridge with the same
"lan" name was failing.

Reported-by: David Bauer <mail@david-bauer.net>
Fixes: 43fc720657c6 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agobusybox: preserve crontabs
Philip Prindeville [Wed, 5 May 2021 23:43:55 +0000 (17:43 -0600)]
busybox: preserve crontabs

/etc/syslog.conf is used by sysklogd, and /etc/crontabs is used
by crond, both features of busybox.  Given this, ownership for
these files should be bound to busybox, especially if one day
there's a way to do an in-place opkg update of busybox.

There's also the busybox provided syslogd which uses this file
if CONFIG_BUSYBOX_FEATURE_SYSLOGD_CFG is set.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
3 years agobusybox: remove nslookup_lede/openwrt.patch
Nick Hainke [Wed, 12 May 2021 18:36:58 +0000 (20:36 +0200)]
busybox: remove nslookup_lede/openwrt.patch

The nslookup_lede/openwrt applet was introduced in de5b8e5. It was
introduced because:

  Add a new LEDE nslookup applet which is compatible with musl libc
  and providing more features like ability to specify query type.

  In contrast to busybox' builtin nslookup applet, this variant does
  not rely on libc resolver internals but uses explicit send logic
  and the libresolv primitives to parse received DNS responses.

In busybox this applet is added in 0dd3be8. In particular, this commit
introduces the variable NSLOOKUP_BIG. We set the default to true and
so nothing changes.

Signed-off-by: Nick Hainke <vincent@systemli.org>
3 years agobusybox: show reproducible timestamp
Paul Spooren [Thu, 13 May 2021 21:57:45 +0000 (23:57 +0200)]
busybox: show reproducible timestamp

On login busybox shows a timestamp per default contianing the build
date. Since the build date isn't reproducible per default this behaviour
was disabled by default via 34df4d40 "busybox: disable timestamp in
version".

This commit modifies busybox so that the printed timestamp reproducible
using SOURCE_DATE_EPOCH and therefore shouldn't be disabled anymore.

Before:

    BusyBox v1.33.1 () built-in shell (ash)

After:

    BusyBox v1.33.1 (2021-05-13 09:34:34 UTC) built-in shell (ash)

Signed-off-by: Paul Spooren <mail@aparcar.org>
3 years agobase-files: migrate old UCI network bridge ports syntax
Rafał Miłecki [Sat, 15 May 2021 21:04:35 +0000 (23:04 +0200)]
base-files: migrate old UCI network bridge ports syntax

netifd has been recently patched to use more accurate "ports" option
instead of "ifname". This is a simple translation between two UCI
options.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agobase-files: generate "device" UCI type section for bridge
Rafał Miłecki [Sat, 15 May 2021 19:06:27 +0000 (21:06 +0200)]
base-files: generate "device" UCI type section for bridge

This switches from the old way of defining bridges in an "interface" UCI
section type (that should be used for layer 3 only). From now a defualt
board switch will have its own "device" UCI section type. It's a new &
preferred way of defining L2 devices.

Before:

config interface 'lan'
        option type 'bridge'
        option ifname 'lan1 lan2 lan3 lan4'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'

After:

config device
        option name 'lan'
        option type 'bridge'
        list ports 'lan1'
        list ports 'lan2'
        list ports 'lan3'
        list ports 'lan4'

config interface 'lan'
        option ifname 'lan'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agorpcd: fix PKG_MIRROR_HASH
David Bauer [Tue, 18 May 2021 17:30:09 +0000 (19:30 +0200)]
rpcd: fix PKG_MIRROR_HASH

Fixes commit 97e820c6d61d ("rpcd: update to latest HEAD")

Signed-off-by: David Bauer <mail@david-bauer.net>
3 years agobusybox: use $(AUTORELEASE) and SPDX
Paul Spooren [Tue, 18 May 2021 13:36:10 +0000 (15:36 +0200)]
busybox: use $(AUTORELEASE) and SPDX

use AUTORELEASE since BusyBox is often updaten and PKG_RELEASE is not
consistently bumped. Also use SPDX license headers to be machine
readable and bump the copyright year to 2021.

Signed-off-by: Paul Spooren <mail@aparcar.org>
3 years agonetifd: update to the latest version
Felix Fietkau [Tue, 18 May 2021 10:52:31 +0000 (12:52 +0200)]
netifd: update to the latest version

02dd2f2df7cb fix unannotated fall-through warnings
3052f2f67686 extdev: remove unused function
2a97fd006c3b device: add support for configuring devices with external auth handler
87e469be0c08 wireless: fix memory corruption bug when using vlans/station entries in the config
7277764bf817 bridge: rename "ifname" attribute to "ports"

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: add patch for disabling automatic bridging of vlan interfaces
Felix Fietkau [Tue, 18 May 2021 10:50:17 +0000 (12:50 +0200)]
hostapd: add patch for disabling automatic bridging of vlan interfaces

netifd is responsible for handling that, except if the vlan bridge
was provided by the config

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agohostapd: add ubus notifications for adding/removing vlan interfaces
Felix Fietkau [Tue, 18 May 2021 10:16:11 +0000 (12:16 +0200)]
hostapd: add ubus notifications for adding/removing vlan interfaces

This can be used to handle network configuration of dynamically created vlan
interfaces in a more flexible way

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agolibubox: update to the latest version
Felix Fietkau [Mon, 17 May 2021 15:58:52 +0000 (17:58 +0200)]
libubox: update to the latest version

870acee325fe tests: cram: test_base64: fix failing tests
4d8995e91d56 tests: cram: test_base64: really fix failing tests
551d75b5662c libubox: tests: add more blobmsg/json test cases
a0dbcf8b8f96 tests: add blob-buffer overflow test
b36a3a90098d blob: fix exceeding maximum buffer length
b8abed749423 utils.h: add fallthrough macro
b14c4688612c json_script: fix unannotated fall-through warning

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agotoolchain/gdb: fix broken configure test for ELF support
Felix Fietkau [Mon, 17 May 2021 15:16:56 +0000 (17:16 +0200)]
toolchain/gdb: fix broken configure test for ELF support

A missing #include was causing gdb on macOS to be compiled without ELF support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
3 years agobase-files: use "ports" array in board.json network for bridges
Rafał Miłecki [Fri, 14 May 2021 09:09:57 +0000 (11:09 +0200)]
base-files: use "ports" array in board.json network for bridges

Bridge aggregates multiple ports so use a more accurate name ("ports")
and format (array) for storing them in board.json.

Example:

"network": {
"lan": {
"ports": [
"lan1",
"lan2",
"lan3",
"lan4"
],
"protocol": "static"
},
"wan": {
"ifname": "wan",
"protocol": "dhcp"
}
}

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
3 years agoopenwrt-keyring: Only copy sign key for snapshots
Hauke Mehrtens [Wed, 12 May 2021 23:25:55 +0000 (01:25 +0200)]
openwrt-keyring: Only copy sign key for snapshots

Instead of adding all public signature keys from the openwrt-keyring
repository only add the key which is used to sign the master feeds.

If one of the other keys would be compromised this would not affect
users of master snapshot builds.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3 years agobmips: remove duplicated brcmnand patch
Álvaro Fernández Rojas [Mon, 17 May 2021 10:25:34 +0000 (12:25 +0200)]
bmips: remove duplicated brcmnand patch

brcmnand patch was applied upstream on 5.10.37 update.

Fixes: d337731f85c8 ("kernel: bump 5.10 to 5.10.37")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
3 years agoocteon: use shared function for platform_copy_config()
Adrian Schmutzler [Sun, 16 May 2021 21:58:59 +0000 (23:58 +0200)]
octeon: use shared function for platform_copy_config()

This reduces redundant instructions.

The solution is inspired by a different implemention of
Roman Kuzmitskii.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
3 years agoath79: add support for ZiKing CPE46B
Giulio Lorenzo [Tue, 6 Oct 2020 12:14:31 +0000 (14:14 +0200)]
ath79: add support for ZiKing CPE46B

ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b

Specifications:

- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging

Flashing instruction:

You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.

Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
3 years agoath79: fix leading whitespaces in generic 01_leds
Adrian Schmutzler [Sun, 16 May 2021 19:37:43 +0000 (21:37 +0200)]
ath79: fix leading whitespaces in generic 01_leds

Use tabs consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
3 years agoath79: add support for COMFAST CF-E375AC
Joao Henrique Albuquerque [Fri, 14 Aug 2020 15:04:02 +0000 (12:04 -0300)]
ath79: add support for COMFAST CF-E375AC

COMFAST CF-E375AC is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.

Short specification:

    2x 10/100/1000 Mbps Ethernet, with PoE support
    128MB of RAM (DDR2)
    16 MB of FLASH
    3T3R 2.4 GHz, 802.11b/g/n
    2T2R 5 GHz, 802.11ac/n/a, wave 2
    built-in 5x 3 dBi antennas
    output power (max): 500 mW (27 dBm)
    1x RGB LED, 1x button
    built-in watchdog chipset

Flash instruction:
1) Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

2) TFTP
2.1) Set a tftp server on your machine with a fixed IP address of
     192.168.1.10. A place the sysupgrade as firmware_auto.bin.
2.2) boot the device with an ethernet connection on fixed ip route
2.3) wait a few seconds and try to login via ssh

3) TFTP trough Bootloader
3.1) open the device case and get a uart connection working
3.2) stop the autoboot process and test connection with serverip
3.3) name the sysupgrade image firmware.bin and run firmware_upg

MAC addresses:
Though the OEM firmware has four adresses in the usual locations,
it appears that the assigned addresses are just incremented in a
different way:

interface    address    location
LAN:          *:DC      0x0
WAN           *:DD      0x1002
WLAN 2.4g     *:E6      n/a (0x0 + 10)
WLAN 5g       *:DE      0x6
unused        *:DF      0x5006

The MAC address pointed at the label is the one assign to the LAN
interface.

Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
[add label-mac-device, remove redundant uart status, fix whitespace
issues, fix commit message wrapping, remove x bit on DTS file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>