openwrt/staging/hauke.git
2 years agomediatek: fix Unifi 6LR network config
Stijn Tintel [Tue, 20 Sep 2022 16:27:34 +0000 (19:27 +0300)]
mediatek: fix Unifi 6LR network config

When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.

Fix this by using a wildcard that matches all the variants.

Fixes: 15a02471bb85 ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a78f ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a1192 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 117f41ee95ec445dce5ab9332bc27a6311747c0d)

2 years agompc85xx: fix unset kernel symbols
David Bauer [Tue, 20 Sep 2022 19:08:23 +0000 (21:08 +0200)]
mpc85xx: fix unset kernel symbols

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agomac80211: rt2x00: experimental improvements for MT7620 wifi
Daniel Golle [Thu, 28 Jul 2022 11:40:12 +0000 (13:40 +0200)]
mac80211: rt2x00: experimental improvements for MT7620 wifi

Serge Vasilugin reports:

To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
   set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
    a) RF and BBP regs never be corrected for this mode
    b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough

First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA

Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
 35-40/30-35 Mbps for HT20
 65-70/60-65 Mbps for HT40

Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.

Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[directly include v3 of the patchset submitted upstream]
(cherry picked from commit 31a6605de04218e1c04bd5c2436c24d7d1c07506)
(cherry picked from commit e785ca05e9f0502894772f5df92192b816ba5d7c)
(cherry picked from commit 412fcf3d4400f84551f3ead0514834c62d94a251)

2 years agomac80211: rt2x00: fix typo
Sungbo Eo [Mon, 31 Jan 2022 17:53:59 +0000 (02:53 +0900)]
mac80211: rt2x00: fix typo

Add missing semicolon and refresh patches.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit d826c91704d2baa5e389c225791740e4c61d62c4)

2 years agomac80211: add patch descriptions to rt2x00 patches
Daniel Golle [Mon, 12 Sep 2022 20:21:05 +0000 (21:21 +0100)]
mac80211: add patch descriptions to rt2x00 patches

Prepare patches for sending upstream by adding patch descriptions
generated from the original OpenWrt commits adding each patch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d4feb66048f6a8f387eedfb162a1184cdae9d756)

2 years agomediatek: fix ledbar of UniFi 6 LR when running custom U-Boot
Daniel Golle [Sun, 11 Sep 2022 19:24:05 +0000 (20:24 +0100)]
mediatek: fix ledbar of UniFi 6 LR when running custom U-Boot

The RGB LED of the UniFi 6 LR v1 doesn't work when using the Openwrt-
built U-Boot. This is because the vendor loader resets the ledbar
controller while our U-Boot doesn't care.
Add reset-gpio so the ledbar driver in Linux will always reset the
ledbar controller.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0b5cf952cf5b70d3af2424d05b15ce2730a3dc11)

2 years agoramips: add support for Ubiquiti UniFi FlexHD
Sven Wegener [Sat, 1 May 2021 11:51:51 +0000 (13:51 +0200)]
ramips: add support for Ubiquiti UniFi FlexHD

Hardware
--------

- SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash
- Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4)
- Bluetooth: CSR8811 (internal USB, install kmod-bluetooth)

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt".

2. Update the bootloader environment.

   $ fw_setenv devmode TRUE
   $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
     fdt rm /signature; bootubnt"
   $ fw_setenv bootcmd "run boot_openwrt"

3. Transfer the OpenWrt sysupgrade image to the device using SCP.

4. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

5. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4

6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock6
   $ dd if=openwrt.bin of=/dev/mtdblock7

7. Reboot the device. It should boot into OpenWrt.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 820f0c07c544652c1c53a45262a481ac5dbe139b)

2 years agoath79: Make patches apply again
Daniel Golle [Sun, 18 Sep 2022 14:38:47 +0000 (15:38 +0100)]
ath79: Make patches apply again

The patch adding support for LEDs connected to a reset controller did
not apply any more, refresh it on top of current master.

Fixes: 53fc987b2552 ("generic: move ledbar driver from mediatek target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 76fc277917fc847892dbbf525aea9f90a035d296)

2 years agogeneric: move ledbar driver from mediatek target
Sven Wegener [Mon, 2 May 2022 20:13:14 +0000 (22:13 +0200)]
generic: move ledbar driver from mediatek target

This moves the ledbar driver to generic, to be also used by the ramips target.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 53fc987b25524c28525313347f0e2e5653dce43c)

2 years agomediatek: add led count
Sven Wegener [Sat, 12 Jun 2021 19:56:22 +0000 (21:56 +0200)]
mediatek: add led count

The LEDs connected to the MCU are so-called smart LEDs and their signal is
daisy-chained. Because of this, the MCU needs to be told how many LEDs are
connected. It also means the LEDs could be individually controlled, if the MCU
has a command for this.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 76198e8f09a607c6aca2621f59d7a4cd7f6653e3)

2 years agomediatek: add initialization after reset
Sven Wegener [Sat, 12 Jun 2021 19:56:22 +0000 (21:56 +0200)]
mediatek: add initialization after reset

During GPIO initialization the pin state flips and triggers a reset of
the ledbar MCU. It needs to be moved through an initialization sequence
before working correctly.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 013a956f086dc5d88f6e9cbd852ed4d900d436e0)

2 years agomediatek: add support for reset gpio
Sven Wegener [Sat, 12 Jun 2021 19:56:22 +0000 (21:56 +0200)]
mediatek: add support for reset gpio

Some versions of the ledbar MCU have a reset pin. It needs to be
correctly initialized or we might keep the MCU in reset state.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 84e4bbf5f049cdb862eb25c446bd6973ed4238aa)

2 years agomediatek: support reading more than one byte of response
Sven Wegener [Sat, 12 Jun 2021 19:56:21 +0000 (21:56 +0200)]
mediatek: support reading more than one byte of response

There are commands that return more than one byte of response.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 7c852e7df50e370b26b060c96c3cc4491cee88eb)

2 years agomediatek: cast literal value to char
Sven Wegener [Sat, 12 Jun 2021 19:56:21 +0000 (21:56 +0200)]
mediatek: cast literal value to char

Or the comparison against a signed char is always true, because the
literal 0xaa is treated as an unsigned int, to which the signed char is
casted during comparison. 0xaa is above the positive values of a signed
char and negative signed char values result in values larger than 0xaa
when casted to unsigned int.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit e9a22ce2535c4a0faf83d5595304fe0e2c7bd1b2)

2 years agomediatek: correctly log i2c response
Sven Wegener [Sat, 12 Jun 2021 19:56:21 +0000 (21:56 +0200)]
mediatek: correctly log i2c response

The read response is in the i2c_response variable. Also use %hhx format,
because we're dealing with a single char.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit c4f9f9b44c82ffeacd9d3c00ba07171c35831337)

2 years agomediatek: remove gpiod_direction_output()
Sven Wegener [Sat, 12 Jun 2021 19:56:21 +0000 (21:56 +0200)]
mediatek: remove gpiod_direction_output()

It's already set to output with GPIOD_OUT_LOW.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit a188356484f434c72ea536d91d7f93f59c562eb5)

2 years agomediatek: do not use gpiod_set_raw_value()
Sven Wegener [Sat, 12 Jun 2021 19:56:21 +0000 (21:56 +0200)]
mediatek: do not use gpiod_set_raw_value()

The polarity of the signal is set in the device dts.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 56c2d15587dfe5285f1cf3bfb236c827bc446465)

2 years agokernel: modules: package kmod-crypto-essiv
Daniel Golle [Sun, 11 Sep 2022 13:26:25 +0000 (14:26 +0100)]
kernel: modules: package kmod-crypto-essiv

Package kernel module providing ESSIV support for block encryption.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4133102898502c9bb453e8603b6c891aa103bce4)

2 years agomediatek: fix typo in bpi-r64 image recipe
Daniel Golle [Thu, 8 Sep 2022 18:29:44 +0000 (19:29 +0100)]
mediatek: fix typo in bpi-r64 image recipe

Janusz Dziedzic reported a typo introduced by a recent commit. Fix it.

Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 007c8809c1e888748af70c1b878f4d0105fe7531)

2 years agomediatek: bpi-r64: make initramfs/recovery optional
Daniel Golle [Thu, 8 Sep 2022 01:44:30 +0000 (02:44 +0100)]
mediatek: bpi-r64: make initramfs/recovery optional

Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 50c892d67bb4af90861be9fbb6831c2eeb62de11)

2 years agoramips: fix GB-PC1 and GB-PC2 LEDs
Arınç ÜNAL [Wed, 14 Sep 2022 18:30:59 +0000 (21:30 +0300)]
ramips: fix GB-PC1 and GB-PC2 LEDs

Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.

Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.

Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.

Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 2a6ef7f53d7b96e4ee0200196c28ed6b0a7c8465)

2 years agowireless-regdb: update to 2022-08-12
Nick Hainke [Sat, 17 Sep 2022 06:05:47 +0000 (08:05 +0200)]
wireless-regdb: update to 2022-08-12

Changes:
9dc9c89 wireless-regdb: update regulatory database based on preceding changes
442bc25 wireless-regdb: update 5 GHz rules for PK and add 60 GHz rule
daee7f3 wireless-regdb: add 5 GHz rules for GY

Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 1d2d69c810261308652a577fc136e7327e0e1358)

2 years agokernel: bump 5.10 to 5.10.143
John Audia [Thu, 15 Sep 2022 13:56:36 +0000 (09:56 -0400)]
kernel: bump 5.10 to 5.10.143

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit b77217d916ba48accbdb46589e6e5e3a9972c44e)

2 years agokernel: bump 5.10 to 5.10.142
John Audia [Thu, 8 Sep 2022 10:19:20 +0000 (06:19 -0400)]
kernel: bump 5.10 to 5.10.142

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 837fd23c80b22c566b40181a28630ac29af8f96e)

2 years agokernel: bump 5.10 to 5.10.141
John Audia [Mon, 5 Sep 2022 10:47:34 +0000 (06:47 -0400)]
kernel: bump 5.10 to 5.10.141

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit e8a62a1e6040de71bdcb1be1a1c30c064acbc059)

2 years agokernel: bump 5.10 to 5.10.139
John Audia [Mon, 29 Aug 2022 15:30:27 +0000 (11:30 -0400)]
kernel: bump 5.10 to 5.10.139

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit e0753c5d5cef5b03c60601364188afb262ccd02e)

2 years agokernel: build crypto md5/sha1/sha256 modules for powerpc
Josef Schlehofer [Tue, 30 Aug 2022 07:02:32 +0000 (09:02 +0200)]
kernel: build crypto md5/sha1/sha256 modules for powerpc

This builds and enables kernel optimized modules for mpc85xx target:
- CONFIG_CRYPTO_MD5_PPC [1]
- CONFIG_CRYPTO_SHA1_PPC_SPE [2]
- CONFIG_CRYPTO_SHA256_PPC_SPE [3]

Where it was possible, then use Signal Processing Engine, because
CONFIG_SPE is already enabled in mpc85xx config.

[1] https://cateee.net/lkddb/web-lkddb/CRYPTO_MD5_PPC.html
[2] https://cateee.net/lkddb/web-lkddb/CRYPTO_SHA1_PPC.html
[3] https://cateee.net/lkddb/web-lkddb/CRYPTO_SHA256_PPC_SPE.html

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 3a702f8733ff371f30e9e3ba1e1aed5f4686b6b4)

2 years agoscripts/download.pl: fix downloads with wget
Petr Štetiar [Tue, 13 Sep 2022 05:40:37 +0000 (07:40 +0200)]
scripts/download.pl: fix downloads with wget

Several users of wget for downloads (curl is not available in the
system) have reported broken download functionality:

 wget --tries=5 --timeout=20 --output-document=-  https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.10.142.tar.xz
 http://: Invalid host name.

Thats all happening due to '' was passed as an argument, which got later
expanded to http://.

In the context of a list constructor '' is not nothing, it is an empty
string element.  So fix it by using () as it will yield "nothing" and
thus not introduce an empty string element.

Fixes: #10692
Fixes: 90c6e3aedf16 ("scripts: always check certificates")
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [shellwords() -> ()]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 50a48faa1b8424e6b4b436b7118fffa2cba14b18)

2 years agoscripts/download.pl: silence can't exec curl warning
Petr Štetiar [Tue, 13 Sep 2022 05:38:10 +0000 (07:38 +0200)]
scripts/download.pl: silence can't exec curl warning

When running build in verbose mode `make V=s` we can see a lot of
following warnings when curl is not available in the system:

 Can't exec "curl": No such file or directory at scripts/download.pl line 77.

So lets fix it by redirecting of the stderr to null hole.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c836ca84e8f641e10a8349a8f9b7432b33d6cec1)

2 years agoscripts: always check certificates
Josh Roys [Sat, 23 Jul 2022 15:23:16 +0000 (11:23 -0400)]
scripts: always check certificates

Remove flags from wget and curl instructing them to ignore bad server
certificates. Although other mechanisms can protect against malicious
modifications of downloads, other vectors of attack may be available
to an adversary.

TLS certificate verification can be disabled by turning oof the
"Enable TLS certificate verification during package download" option
enabled by default in the "Global build settings" in "make menuconfig"

Signed-off-by: Josh Roys <roysjosh@gmail.com>
[ add additional info on how to disable this option ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 90c6e3aedf167b0ae1baf376e7800a631681e69a)

2 years agotools: remove xxd package
Petr Štetiar [Tue, 30 Aug 2022 06:41:07 +0000 (08:41 +0200)]
tools: remove xxd package

It shouldn't be needed anymore as we've now `scripts/xxdi.pl`, which
should be self contained and fully compatible `xxd -i` replacement.

Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 88c9056a70901577489ecdc7a25207a9b7576d6e)

2 years agobuild: provide xxd -i with scripts/xxdi.pl
Petr Štetiar [Tue, 30 Aug 2022 06:45:39 +0000 (08:45 +0200)]
build: provide xxd -i with scripts/xxdi.pl

Dependency on xxd was added in commit c4dd2441e787 ("tools: add xxd
(from vim)") as U-Boot requires xxd to create the default environment
from an external file.

Later in commit 2b94aac7a128 ("tools: xxd: use more convenient source
tarball"), xxd from another source was used instead, but that source is
currently unavailable, so let's fix it by using simple xxdi.pl Perl
script instead.

Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit eae2fb8027cb892e42181e471ba344aa5d26bf7e)

2 years agoscripts: xxdi.pl: add xxd -i compat mode
Petr Štetiar [Tue, 30 Aug 2022 06:34:26 +0000 (08:34 +0200)]
scripts: xxdi.pl: add xxd -i compat mode

So it can serve as a standalone drop in replacement for xxd utility used
currently mostly in U-Boot packages with `xxd -i` mode which outputs C
include file style, with aim for byte to byte identical output, so the
eventual difference in the generated output is easily spottable.

Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [perl-fu]
(cherry picked from commit 06e01e817ec6643a35beb9e6946689e9cc7d020a)

2 years agoscripts: xxdi.pl: remove File::Slurp dependency
Jo-Philipp Wich [Tue, 30 Aug 2022 16:20:04 +0000 (18:20 +0200)]
scripts: xxdi.pl: remove File::Slurp dependency

In order to make it more portable.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8b278a76d90e3724815a5fde32be59f7796be1d8)

2 years agoscripts: add xxdi.pl
Petr Štetiar [Tue, 30 Aug 2022 06:31:42 +0000 (08:31 +0200)]
scripts: add xxdi.pl

xxdi.pl is a Perl script that implements vim's 'xxd -i' mode so that
packages do not have to use all of vim just to get this functionality.

References: #10555
Source: https://github.com/gregkh/xxdi/blob/97a6bd5cee05d1b15851981ec38ef5a460ddfcb1/xxdi.pl
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 2117d04a3aaad3394c0afec799d9c43f8a09c2cf)

2 years agomac80211: backport tx queueing bugfixes add a bug fix for a rare crash
Felix Fietkau [Sat, 26 Mar 2022 23:05:49 +0000 (00:05 +0100)]
mac80211: backport tx queueing bugfixes add a bug fix for a rare crash

Re-introduce the queue wake fix that was reverted due to a regression,
but this time with the follow-up fixes that take care of the regression.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9a93b62f315ad4c9f021c414ed80ba337ab4a01e)
(cherry-picked from commit 8b804cae5e039142bc63896a75f15146eca3bebc)
(cherry-picked from commit 8b06e06832ebe757246582b65306ad2a2537741f)

2 years agobcm53xx: update NVMEM driver for NVRAM
Rafał Miłecki [Wed, 14 Sep 2022 12:20:38 +0000 (14:20 +0200)]
bcm53xx: update NVMEM driver for NVRAM

Include support for NVMEM cells.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 2f50c53f1772f24e4687e960e21c5b392fb522f0)

2 years agokernel: backport mtd dynamic partition patch
Christian Marangi [Wed, 29 Jun 2022 15:34:51 +0000 (17:34 +0200)]
kernel: backport mtd dynamic partition patch

Backport upstream solution that permits to declare nvmem cells with
dynamic partition defined by special parser.

This provide an OF node for NVMEM and connect it to the defined dynamic
partition.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1a9ee367343edce263f82cc91a49d796c9d45ea3)

2 years agoipq40xx: add GL-AP1300 label-mac-device
David Bauer [Sun, 11 Sep 2022 14:23:03 +0000 (16:23 +0200)]
ipq40xx: add GL-AP1300 label-mac-device

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 470ca65bda154fb5a601c6bbe20e20646535563f)

2 years agoipq40xx: add WAN LED mapping for GL-AP1300
David Bauer [Sat, 10 Sep 2022 12:05:34 +0000 (14:05 +0200)]
ipq40xx: add WAN LED mapping for GL-AP1300

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4d014a7bd6d8fbfe7dc4cebd6c55d85601231fa4)

2 years agorockchip: add system-LED aliases specific to OpenWrt
David Bauer [Fri, 9 Sep 2022 21:35:49 +0000 (23:35 +0200)]
rockchip: add system-LED aliases specific to OpenWrt

Add the aliases sections required to detect LEDs specific to OpenWrt
boot / update indication for the NanoPi R4S.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1588069612f5db0720cbb942a6f8787878c223c3)

2 years agorockchip: ensure NanoPi R4S has unique MAC address
David Bauer [Fri, 9 Sep 2022 23:01:57 +0000 (01:01 +0200)]
rockchip: ensure NanoPi R4S has unique MAC address

Ensure the MAC address for all NanoPi R4S boards is assigned unique for
each board.

FriendlyElec ship two versions of the R4S: The standard as well as the
enterprise edition with only the enterprise edition including the EEPROM
chip that stores the unique MAC address.

In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S in case the EEPROM chip is not
present by generating the board MAC from the SD card CID.

[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#Differences_Between_R4S_Standard_Version_.26_R4S_Enterprise_Version

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b5675f500daff3ef3f904e53a5566aa7dc09b786)

2 years agorealtek: fix RTL839x receive tag decoding
Bjørn Mork [Fri, 9 Sep 2022 06:28:13 +0000 (08:28 +0200)]
realtek: fix RTL839x receive tag decoding

The previous fixup was incomplete, and the offsets for the
queue and crc_error cpu_tag bitfields were still wrong on
RTL839x.

Fixes: 545c6113c93b ("realtek: fix RTL838x receive tag decoding")
Suggested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2 years agoipq40xx: add LTE packages for GL-AP1300
David Bauer [Fri, 9 Sep 2022 16:14:08 +0000 (18:14 +0200)]
ipq40xx: add LTE packages for GL-AP1300

Add LTE packages required for operating the LTE modem optionally shipped
with the GL-AP1300.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c7c350922668e262068c9301b75434d7bb4b8d10)

2 years agoath79: add support for ZTE MF281
David Bauer [Mon, 5 Sep 2022 17:23:16 +0000 (19:23 +0200)]
ath79: add support for ZTE MF281

Add support for the ZTE MF281 battery-powered WiFi router.

Hardware
--------
SoC:    Qualcomm Atheros QCA9563
RAM:    128M DDR2
FLASH:  2M SPI-NOR (GigaDevice GD25Q16)
        128M SPI-NAND (GigaDevice)
WLAN:   QCA9563 2T2R 802.11 abgn
        QCA9886 2T2R 802.11 nac
WWAN:   ASRMicro ASR1826
ETH:    Qualcomm Atheros QCA8337
UART:   115200 8n1
        Unpopulated connector next to SIM slot
        (SIM) GND - RX - TX - 3V3
        Don't connect 3V3
BUTTON: Reset - WPS
LED:    1x debug-LED (internal)
        LEDs on front of the device are controlled
        using the modem CPU and can not be controlled
        by OpenWrt

Installation
------------

1. Connect to the serial console. Power up the device and interrupt
   autoboot when prompted

2. Connect a TFTP server reachable at 192.168.1.66 to the ethernet port.
   Serve the OpenWrt initramfs image as "speedbox-2.bin"

3. Boot the initramfs image using U-Boot

   $ setenv serverip 192.168.1.66
   $ setenv ipaddr 192.168.1.154
   $ tftpboot 0x84000000 speedbox-2.bin
   $ bootm

4. Copy the OpenWrt factory image to the device using scp and write to
   the NAND flash

   $ mtd write /path/to/openwrt/factory.bin firmware

WWAN
----

The WWAN card can be used with OpenWrt. Example configuration for
connection with a unauthenticated dual-stack APN:

network.lte=interface
network.lte.proto='ncm'
network.lte.device='/dev/ttyACM0'
network.lte.pdptype='IPV4V6'
network.lte.apn='internet.telekom'
network.lte.ipv6='auto'
network.lte.delay='10'

The WWAN card is running a modified version of OpenWrt and handles
power-management as well as the LED controller (AW9523). A root shell
can be acquired by installing adb using opkg and executing "adb shell".

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1e1695f959e678868bb7911d059b847f38fc9cf4)

2 years agorealtek: fix RTL838x receive tag decoding
Bjørn Mork [Thu, 8 Sep 2022 17:35:34 +0000 (19:35 +0200)]
realtek: fix RTL838x receive tag decoding

Commit dc9cc0d3e2a1 ("realtek: add QoS and rate control") replaced a
16 bit reserved field in the RTL83xx packet header with the initial
cpu_tag word, shifting the real cpu_tag fields by one.  Adjusting for
this new shift was partially forgotten in the new RX tag decoders.

This caused the switch to block IGMP, effectively blocking IPv4
multicast.

The bug was partially fixed by commit 9d847244d9fd ("realtek: fix
RTL839X receive tag decoding")

Fix on RTL838x too, including correct NIC_RX_REASON_SPECIAL_TRAP value.

Suggested-by: Jan Hoffmann <jan@3e8.eu>
Fixes: dc9cc0d3e2a1 ("realtek: add QoS and rate control")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 545c6113c93bbf7de1b0e515141a4565f7e6cece)

2 years agomt76: update to the latest version
Felix Fietkau [Tue, 6 Sep 2022 20:44:43 +0000 (22:44 +0200)]
mt76: update to the latest version

d70546462b7b mt76: fix 5 GHz connection regression on mt76x0/mt76x2

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 33c11442b2fc60313a2d3196c9b01cf9b0931305)

2 years agohostapd: rename hostapd multicast_to_unicast option to multicast_to_unicast_all
Felix Fietkau [Tue, 6 Sep 2022 10:12:12 +0000 (12:12 +0200)]
hostapd: rename hostapd multicast_to_unicast option to multicast_to_unicast_all

There are two feature currently altered by the multicast_to_unicast option.
1. bridge level multicast_to_unicast via IGMP snooping
2. hostapd/mac80211 config multicast_to_unicast setting

The hostapd/mac80211 setting has the side effect of converting *all* multicast
or broadcast traffic into per-station duplicated unicast traffic, which can
in some cases break expectations of various protocols.
It also has been observed to cause ARP lookup failure between stations
connected to the same interface.

The bridge level feature is much more useful, since it only covers actual
multicast traffic managed by IGMP, and it implicitly defaults to 1 already.

Renaming the hostapd/mac80211 option to multicast_to_unicast_all should avoid
unintentionally enabling this feature

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 09ea1db93b53d2c1e4a081f20fbbddd4bffd451d)

2 years agobcm27xx: make NVMEM driver patch apply again
Rafał Miłecki [Sun, 4 Sep 2022 14:38:11 +0000 (16:38 +0200)]
bcm27xx: make NVMEM driver patch apply again

Fixes: 4efa0b70d54f1 ("kernel: backport U-Boot environment data NVMEM driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agobcm4908: enable NVMEM U-Boot env data driver
Rafał Miłecki [Wed, 17 Aug 2022 20:45:11 +0000 (22:45 +0200)]
bcm4908: enable NVMEM U-Boot env data driver

It's needed for devices with U-Boot bootloader.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit fb47b9fa1aa760de58f1b43d9f3e654acf1f1671)

2 years agokernel: backport U-Boot environment data NVMEM driver
Rafał Miłecki [Wed, 17 Aug 2022 18:44:52 +0000 (20:44 +0200)]
kernel: backport U-Boot environment data NVMEM driver

It parses U-Boot env data into NVMEM cells.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 34cf31043504473df3174a22d163b71b75e46542)

2 years agokernel: backport mtd patch adding of_platform_populate() calls
Rafał Miłecki [Fri, 8 Jul 2022 05:58:20 +0000 (07:58 +0200)]
kernel: backport mtd patch adding of_platform_populate() calls

This is required for non-parser drivers handling MTD devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 41e1e838fbbb0308ad7353a3714e04b8c4585e7e)

2 years agoOpenWrt v22.03.0: revert to branch defaults
Hauke Mehrtens [Sat, 3 Sep 2022 16:49:08 +0000 (18:49 +0200)]
OpenWrt v22.03.0: revert to branch defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoOpenWrt v22.03.0: adjust config defaults v22.03.0
Hauke Mehrtens [Sat, 3 Sep 2022 16:49:01 +0000 (18:49 +0200)]
OpenWrt v22.03.0: adjust config defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agouboot-mediatek: mt7622: suppress unwanted pinctrl warning
Daniel Golle [Sat, 3 Sep 2022 02:53:56 +0000 (03:53 +0100)]
uboot-mediatek: mt7622: suppress unwanted pinctrl warning

Import patch which removes the default pinctrl of uart0 to suppress
the unwanted warning. Apply also to downstream boards.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: mt7622: fix DTS compatible of UniFi 6 LR variants
Daniel Golle [Sat, 3 Sep 2022 01:24:14 +0000 (02:24 +0100)]
mediatek: mt7622: fix DTS compatible of UniFi 6 LR variants

Make sure the compatible string in DTS matches the now v1/v2
differentiated board name in target/linux/mediatek/image/mt7622.mk.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit be555b9dd8618b8da68c42ae8dda493337519838)

2 years agouboot-mediatek: backport fix for unstable UART on MT7622
Daniel Golle [Sat, 3 Sep 2022 00:57:08 +0000 (01:57 +0100)]
uboot-mediatek: backport fix for unstable UART on MT7622

Import pending patch "arm: dts: mt7622: force high-speed mode for uart"
from Weijie Gao <weijie.gao@mediatek.com> fixing the UART problems on
MT7622 which made it hard to use the U-Boot menu on devices with this
SoC.

This patch is also contained in commit
 c09eb08dad ("uboot-mediatek: add support for MT798x platforms")
in the development branch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agouboot-mediatek: no compression means IH_COMP_NONE
Daniel Golle [Mon, 15 Aug 2022 11:19:15 +0000 (13:19 +0200)]
uboot-mediatek: no compression means IH_COMP_NONE

Treat missing compression node in FIT image as IH_COMP_NONE.
This is implicentely already happening in most places, but for now
was still triggering an annoying warning about initramfs compression
being obsolete despite compression note being absent.
Fix this.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0a18456ffc25d6a26911fca6f9079090243c2284)

2 years agouboot-mediatek: fix factory reset on UBI
Daniel Golle [Sun, 28 Aug 2022 19:20:31 +0000 (20:20 +0100)]
uboot-mediatek: fix factory reset on UBI

Truncating a UBI volume using `ubi write 0x0 volname 0x0` results in
segfault on newer U-Boot. Write 1MB of 0s instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d118cbdfece181994a96d1bcb1868bd807d481bf)

2 years agouboot-envtools: mt7622: use 4k sectors for UniFi 6 LR (ubootmod)
Daniel Golle [Sun, 28 Aug 2022 15:07:05 +0000 (16:07 +0100)]
uboot-envtools: mt7622: use 4k sectors for UniFi 6 LR (ubootmod)

Use 4k sectors when accessing the U-Boot environment on the 64MiB
SPI-NOR flash chip found in the UniFi 6 LR. The speeds up environment
write access as only 4kB instead of 64kB have to be written.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f0adf253fdcf78ce005dad9652b405a4ad2726e6)

2 years agomediatek: mt7622: use variable sector size for spi-nor
Daniel Golle [Sun, 28 Aug 2022 15:05:30 +0000 (16:05 +0100)]
mediatek: mt7622: use variable sector size for spi-nor

Make use of minor sector size (4k) on supported SPI-NOR flash chips.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 51f4c8417819bc0ba6bc1808328478503e179fc4)

2 years agouboot-mediatek: fix Ubiquiti UniFi 6 LR U-Boot mod
Daniel Golle [Sun, 28 Aug 2022 15:01:12 +0000 (16:01 +0100)]
uboot-mediatek: fix Ubiquiti UniFi 6 LR U-Boot mod

Image names as well as the calculation of the padded image size did
not work as intended. Fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0bc8889e7b4f19d7e33a9be6c3db918fed051501)

2 years agompc85xx: Drop pci aliases to avoid domain changes
Martin Kennedy [Tue, 30 Aug 2022 00:47:24 +0000 (20:47 -0400)]
mpc85xx: Drop pci aliases to avoid domain changes

As of upstream Linux commit 0fe1e96fef0a ("powerpc/pci: Prefer PCI
domain assignment via DT 'linux,pci-domain' and alias"), the PCIe
domain address is no longer numbered by the lowest 16 bits of the PCI
register address after a fallthrough. Instead of the fallthrough, the
enumeration process accepts the alias ID (as determined by
`of_alias_scan()`). This causes e.g.:

9000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11)
9000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ...

to become

0000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11)
0000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ...

... which then causes the sysfs path of the netdev to change,
invalidating the `wifi_device.path`s enumerated in
`/etc/config/wireless`.

One other solution might be to migrate the uci configuration, as was
done for mvebu in commit 0bd5aa89fcf2 ("mvebu: Migrate uci config to
new PCIe path"). However, there are concerns that the sysfs path will
change once again once some upstream patches[^2][^3] are merged and
backported (and `CONFIG_PPC_PCI_BUS_NUM_DOMAIN_DEPENDENT` is enabled).

Instead, remove the aliases and allow the fallthrough to continue for
now. We will provide a migration in a later release.

This was first reported as a Github issue[^1].

[^1]: https://github.com/openwrt/openwrt/issues/10530
[^2]: https://lore.kernel.org/linuxppc-dev/20220706104308.5390-1-pali@kernel.org/t/#u
[^3]: https://lore.kernel.org/linuxppc-dev/20220706101043.4867-1-pali@kernel.org/

Fixes: #10530
Tested-by: Martin Kennedy <hurricos@gmail.com>
[Tested on the Aerohive HiveAP 330 and Extreme Networks WS-AP3825i]
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(cherry picked from commit 7f4b4c29f3489697dca7495216460d0ed5023e02)

2 years agoat91bootstrap: use sdmmc0 as booting media for sama5d27_som1_ek
Claudiu Beznea [Thu, 28 Jul 2022 10:14:59 +0000 (13:14 +0300)]
at91bootstrap: use sdmmc0 as booting media for sama5d27_som1_ek

Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as
default defconfig") changed default booting media for sama5d27_som1_ek
board w/o any reason. Changed it back to sdmmc0 as it is for all the
other Microchip supported distributions for this board (Buildroot,
Yocto Project). The initial commit cannot be cleanly reverted.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
(cherry picked from commit e9f12931e60ee291cd7d2c8fd19a14682dae0197)

2 years agouboot-at91: use sdmmc0 as booting media for sama5d27_som1_ek
Claudiu Beznea [Thu, 28 Jul 2022 10:12:34 +0000 (13:12 +0300)]
uboot-at91: use sdmmc0 as booting media for sama5d27_som1_ek

Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs")
changed the booting media to sdmmc1 as default booting w/o any reason.
The Microchip releases for the rest of supported distributions (Buildroot,
Yocto Project) uses sdmmc0 as default booting media for this board.
Thus change it back to sdmmc0. With this remove references to sdmmc1
config. The initial commit cannot be cleanly reverted.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
(cherry picked from commit 9a49788008c18fd4fe6fefe9697962c102fb14c6)

2 years agokernel: rename 5.20 patches to 6.0
Rafał Miłecki [Wed, 17 Aug 2022 09:04:29 +0000 (11:04 +0200)]
kernel: rename 5.20 patches to 6.0

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 372ee1919d281dd3e86121996805291a6948c982)

2 years agobcm4908: enable & setup packet steering
Rafał Miłecki [Thu, 28 Jul 2022 15:46:33 +0000 (17:46 +0200)]
bcm4908: enable & setup packet steering

Without packet steering NAT masquarade speed on BCM4908 /jumps/ between
two speeds:
1. 826 Mb/s (±3 Mb/s)
2. 909 Mb/s (±8 Mb/s)
and it never reaches ~940 Mb/s.

Proper packet steering can improve it. Below are testing results for
running iperf TCP traffic from LAN to WAN. They were used to pick up
golden values.

┌──────────┬──────────┬───────────┐
│   eth0   │  br-lan  │   speed   │
│ rps_cpus │ rps_cpus │   [Mbps]  │
├──────────┼──────────┼───────────┤
│        0 │        0 │ 743 / 804 │
│        0 │        1 │ 738 / 821 │
│        0 │        2 │     ✓ 940 │
│        0 │        4 │     ✓ 938 │
│        0 │        8 │     ✓ 941 │
├──────────┼──────────┼───────────┤
│        1 │        0 │       829 │
│        1 │        1 │       829 │
│        1 │        2 │     ✓ 942 │
│        1 │        4 │     ✓ 941 │
│        1 │        8 │     ✓ 941 │
├──────────┼──────────┼───────────┤
│        2 │        0 │     ✓ 942 │
│        2 │        1 │       926 │
│        2 │        2 │     ✓ 942 │
│        2 │        4 │     ✓ 942 │
│        2 │        8 │     ✓ 941 │
├──────────┼──────────┼───────────┤
│        4 │        0 │     ✓ 941 │
│        4 │        1 │       925 │
│        4 │        2 │     ✓ 941 │
│        4 │        4 │     ✓ 941 │
│        4 │        8 │     ✓ 941 │
├──────────┼──────────┼───────────┤
│        8 │        0 │     ✓ 942 │
│        8 │        1 │       925 │
│        8 │        2 │     ✓ 941 │
│        8 │        4 │     ✓ 942 │
│        8 │        8 │     ✓ 942 │
└──────────┴──────────┴───────────┘

Ref: fcbd39689ebfe ("bcm53xx: enable & setup packet steering")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 57cad53f4e52be987cdd61308ff7d2704baca539)

2 years agobcm4908: prepare for Asus GT-AX6000 support
Rafał Miłecki [Wed, 20 Jul 2022 18:03:56 +0000 (20:03 +0200)]
bcm4908: prepare for Asus GT-AX6000 support

It isn't tested & Linux DT will surely need more work.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3f2b2fe084c0019221a17e3217a01c41d003f6fd)

2 years agobcm4908: backport bcmbca DT patches queued for 5.20
Rafał Miłecki [Wed, 20 Jul 2022 16:12:31 +0000 (18:12 +0200)]
bcm4908: backport bcmbca DT patches queued for 5.20

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit d63ef7c90f75393270ec4f5ff1b2563d6bd52066)

2 years agobcm53xx: backport DT changes from 5.17 & 5.18
Rafał Miłecki [Wed, 30 Mar 2022 14:05:55 +0000 (16:05 +0200)]
bcm53xx: backport DT changes from 5.17 & 5.18

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a721fb9f839b3ca71da275a1c99620ef9342fb28)

2 years agobcm53xx: drop dead upgrade code
Rafał Miłecki [Tue, 29 Mar 2022 14:14:54 +0000 (16:14 +0200)]
bcm53xx: drop dead upgrade code

platform_nand_pre_upgrade() is gone since commit 790692dde2b9
("base-files: drop support for the platform_nand_pre_upgrade()").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a6dc0f680d3715322abd7a5dc1426f56274292ac)

2 years agofirewall4: update to latest Git HEAD
Jo-Philipp Wich [Thu, 1 Sep 2022 10:37:58 +0000 (12:37 +0200)]
firewall4: update to latest Git HEAD

f5fcdcf cli: introduce test mode and refuse firewall restart on errors
a540f6d fw4: fix cosmetic issue with per-ruleset and per-table include paths
695e821 doc: fix swapped include positions in nftables.d README

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit ab31ffc425b59afc102f8a3275791c153f39c8f4)

2 years agoucode: update to latest Git HEAD
Jo-Philipp Wich [Mon, 29 Aug 2022 14:02:16 +0000 (16:02 +0200)]
ucode: update to latest Git HEAD

344fa9e lib: extend render() to support function values
89452b2 lib: improve getenv() and split() implementations

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
[fix commit subject]
(cherry picked from commit c6d6306827e9296faad26981996825ce3e90259d)

2 years agomac80211: disable ft-over-ds by default
Felix Fietkau [Tue, 30 Aug 2022 08:57:26 +0000 (10:57 +0200)]
mac80211: disable ft-over-ds by default

Testing has shown it to be very unreliable in variety of configurations.
It is not mandatory, so let's disable it by default until we have a better
solution.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 2984a0420649733662ff95b0aff720b8c2c19f8a)

2 years agoramips: define Yuncore AX820 switch LEDs
Thibaut VARÈNE [Wed, 17 Aug 2022 17:36:41 +0000 (19:36 +0200)]
ramips: define Yuncore AX820 switch LEDs

This patch defines the two switch LED to bring them under user control.

Fixes: 158a5af80102d ("ramips: improve YunCore AX820 LEDs")
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[rmilecki: leave "label"s in place]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7bee10a7d2d16251113147c28dd4548af5c14bab)

2 years agoath79: add support for Extreme Networks WS-AP3805i
Albin Hellström [Thu, 7 Jan 2021 21:51:06 +0000 (22:51 +0100)]
ath79: add support for Extreme Networks WS-AP3805i

Specifications:

 - SoC:    Qualcomm Atheros QCA9557-AT4A
 - RAM:    2x 128MB Nanya NT5TU64M16HG
 - FLASH:  64MB - SPANSION FL512SAIFG1
 - LAN:    Atheros AR8035-A (RGMII GbE with PoE+ IN)
 - WLAN2:  Qualcomm Atheros QCA9557 2x2 2T2R
 - WLAN5:  Qualcomm Atheros QCA9882-BR4A 2x2 2T2R
 - SERIAL: UART pins at J10 (115200 8n1)
           Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
 - LEDs: Power (Green/Amber)
   WiFi 5 (Green)
   WiFi 2 (Green)
 - BTN: Reset

Installation:

1. Download the OpenWrt initramfs-image.

Place it into a TFTP server root directory and rename it to 1D01A8C0.img
Configure the TFTP server to listen at 192.168.1.66/24.

2. Connect the TFTP server to the access point.

3. Connect to the serial console of the access point.

Attach power and interrupt the boot procedure when prompted.

Credentials are admin / new2day

4. Configure U-Boot for booting OpenWrt from ram and flash:

 $ setenv boot_openwrt 'setenv bootargs; bootm 0xa1280000'
 $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
   tftpboot 0x89000000 1D01A8C0.img; bootm'
 $ setenv bootcmd 'run boot_openwrt'
 $ saveenv

5. Load OpenWrt into memory:

 $ run ramboot_openwrt

6. Transfer the OpenWrt sysupgrade image to the device.

Write the image to flash using sysupgrade:

 $ sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: Albin Hellström <albin.hellstrom@gmail.com>
[rename vendor - minor style fixes - update commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f8c87aa2d27ab405f284dd4357377ab5c893a345)

2 years agokernel: Refresh on 5.10.138
Hauke Mehrtens [Sun, 28 Aug 2022 13:09:23 +0000 (15:09 +0200)]
kernel: Refresh on 5.10.138

Refresh all patches on top of kernel 5.10.138.

The following patches were applied upstream:
 bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
 bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch
 bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
 bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch
 bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch
 bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
 bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
 bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch
 bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch
 bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch
 bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch
 bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
 bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch
 bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
 bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch
 bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch

Upstream sets the pixel clock to 340MHz now, do not set it to 600MHz any more.
 bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch

Fixes: 89956c653252 ("kernel: bump 5.10 to 5.10.138")
Fixes: 4209c33ae27d ("kernel: bump 5.10 to 5.10.137")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agombedtls: update to version 2.28.1
Hauke Mehrtens [Sat, 27 Aug 2022 21:11:30 +0000 (23:11 +0200)]
mbedtls: update to version 2.28.1

Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.1
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.

The build problem was reported upstream:
https://github.com/Mbed-TLS/mbedtls/issues/6243

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f3870546a544c39c6fde2e7e014394aa085d8057)

2 years agoRevert "mediatek: mt7622: fix banana pi r64 wps button"
Petr Štetiar [Sun, 28 Aug 2022 06:46:46 +0000 (08:46 +0200)]
Revert "mediatek: mt7622: fix banana pi r64 wps button"

This reverts commit 5a81e0006380c301cdc691838f519275fc6c28d2 as it was
backported upstream in commit a1e238690916 ("arm64: dts: mt7622: fix
BPI-R64 WPS button").

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agokernel: bump 5.10 to 5.10.138
John Audia [Thu, 25 Aug 2022 14:52:50 +0000 (10:52 -0400)]
kernel: bump 5.10 to 5.10.138

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit fc89ec06928469021010c2f5776450f739af07a5)

2 years agokernel: bump 5.10 to 5.10.137
Petr Štetiar [Mon, 22 Aug 2022 20:45:53 +0000 (22:45 +0200)]
kernel: bump 5.10 to 5.10.137

Removed following upstreamed patch:

 * bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch

All other patches automagically rebased.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit d1163fd13f6498826d202f0b58cedf32d7891d52)

2 years agoiptables: default to ip(6)tables-nft when using buildroot
Etienne Champetier [Sat, 20 Aug 2022 22:08:15 +0000 (18:08 -0400)]
iptables: default to ip(6)tables-nft when using buildroot

35fec487e30f05c81bd135326a993dad7f861812 fixed opkg usage,
but when using buildroot we were still defaulting to
ip(6)tables-legacy

Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 0c8d7e34ab35f6b41f034fd94fec740970e0125b)

2 years agoramips: fix GB-PC1 and GB-PC2 device support
Arınç ÜNAL [Tue, 5 Jul 2022 14:10:43 +0000 (17:10 +0300)]
ramips: fix GB-PC1 and GB-PC2 device support

Change switch port labels to ethblack & ethblue.
Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins.
Add the external phy with ethyellow label on the GB-PC2 devicetree.
Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function.
Enable ICPlus PHY driver for IP1001 which GB-PC2 has got.
Update interface name and change netdev function.
Enable lzma compression to make up for the increased size of the kernel.
Make spi flash bindings on par with mainline Linux to fix read errors.

Tested on GB-PC2 by Petr.

Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 4807bd6a00bcf44dd821047db76a2a799f403cd4)

2 years agohostapd: fix WPA3 enterprise keys and ciphers
Joerg Werner [Sun, 26 Jun 2022 15:18:39 +0000 (17:18 +0200)]
hostapd: fix WPA3 enterprise keys and ciphers

WPA3 enterprise requires group_mgmt_cipher=BIP-GMAC-256 and if 802.11r is
active also wpa_key_mgmt FT-EAP-SHA384. This commit also requires
corresponding changes in netifd.

Signed-off-by: Joerg Werner <schreibubi@gmail.com>
(cherry picked from commit 9fbb76c0470fd54f1f34909b1098d0f76078878f)

2 years agoiwinfo: update to latest HEAD
Hauke Mehrtens [Sat, 20 Aug 2022 20:51:29 +0000 (22:51 +0200)]
iwinfo: update to latest HEAD

0dad3e6 Add support for CCMP-256 and GCMP-256 ciphers

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cc6a323e2328176b732b13f1f09745354270cd39)

2 years agoiproute2: Fix KERNEL_INCLUDE in SDK
Hauke Mehrtens [Tue, 16 Aug 2022 21:38:52 +0000 (23:38 +0200)]
iproute2: Fix KERNEL_INCLUDE in SDK

In the SDK the folder $(LINUX_DIR)/user_headers/include does not exist,
but it more or less contains the same content as
$(LINUX_DIR)/include/uapi which also exists in the SDK.

Since iproute2 commit 1d819dcc741e ("configure: fix parsing issue on
include_dir option") it checks if this folder exists and aborts the
build if it does not exists.
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/commit/?id=1d819dcc741e25958190e31f8186c940713fa0a8

With this commit the KERNEL_INCLUDE variable points to a valid folder
with the kernel include headers. I am not sure if they are actually
needed because the build worked before even with an invalid path.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 60738fedede1746922a8b227f24ad5c733661585)

2 years agoumbim: bump to git HEAD
Hauke Mehrtens [Sat, 13 Aug 2022 17:01:15 +0000 (19:01 +0200)]
umbim: bump to git HEAD

146bc77 umbim: fix invalid mbim message string encoding

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 90bedc411b1e98e9adf668dde09f8eafe4490344)

2 years agomt76: update to the latest version
Felix Fietkau [Fri, 26 Aug 2022 17:48:45 +0000 (19:48 +0200)]
mt76: update to the latest version

9485e3b47066 mt76: remove q->qid
e5674c4aa402 mt76: mt7921: enable HW beacon filter not depending on PM flag
7fd299e3c921 mt76: mt7921: enable HW beacon filter in the initialization stage
d5459efaaf14 mt76: mt7921: make mt7921_pci_driver static
b8304b456e23 mt76: connac: move tx initialization/cleanup in mt76_connac module
6e0d7077486c mt76: mt7921: reduce log severity levels for informative messages
cb80da974fe6 mt76: mt7921: reduce the mutex lock scope during reset
a2d61f4f4063 mt76: mt7915 add ht mpdu density
08ea730c1130 mt76: add len parameter to __mt76_mcu_msg_alloc signature
60ef85fa352c mt76: introduce MT_RXQ_BAND2 and MT_RXQ_BAND2_WA in mt76_rxq_id
8ccbb38ca6e6 mt76: add phy_idx in mt76_rx_status
eb19ac83c07e mt76: introduce phys array in mt76_dev structure
30887591e3ab mt76: add phy_idx to mt76_wcid
4bf8c20a9524 mt76: convert MT_TX_HW_QUEUE_EXT_PHY to MT_TX_HW_QUEUE_PHY
e6c6bf8cee09 mt76: get rid of mt76_wcid_hw routine
120f73ad992a mediatek: mt76: mac80211: Fix missing of_node_put() in mt76_led_init()
111e92cf8c22 mediatek: mt76: eeprom: fix missing of_node_put() in mt76_find_power_limits_node()
13bedd62ff4a mt76: connac: introduce mt76_connac_reg_map structure
5ec78e1ec43d wifi: mt76: fix reading current per-tid starting sequence number for aggregation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit ec7d32f3769fbd815f72a7471e4bb7a07aee359d)

2 years agonetifd: update to the latest version
Felix Fietkau [Thu, 25 Aug 2022 19:16:00 +0000 (21:16 +0200)]
netifd: update to the latest version

76d2d41b7355 interface: fix use-after-free bug when rewriting resolv.conf

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 31648c4b59add5b1cb441073a46c80ab768b588c)

2 years agonetifd: update to git HEAD
Hauke Mehrtens [Sat, 20 Aug 2022 20:52:49 +0000 (22:52 +0200)]
netifd: update to git HEAD

87fbefd interface: support "zone" config option
bfa039c netifd: fix WPA3 enterprise ciphers

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry-picked from commit 8008816a2ceeb7e66d27d9882685933bb9df4c76)

2 years agorpcd: bump version to 2022-08-24
Petr Štetiar [Wed, 24 Aug 2022 11:10:37 +0000 (13:10 +0200)]
rpcd: bump version to 2022-08-24

gcc 10 with -O2 reports following:

 In function ‘strncpy’,
     inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:244:4:
 /usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
   106 |   return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
       |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 In function ‘strncpy’,
     inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:227:4:
 /usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
   106 |   return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
       |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Since it is not possible to avoid truncation by strncpy, it is necessary
to make sure the result of strncpy is properly NUL-terminated and the
NUL must be inserted explicitly, after strncpy has returned.

References: #10442
Reported-by: Alexey Smirnov <s.alexey@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 34ddd2e545f068e4684ecce98c1da3a6c7c9b04a)

2 years agorpcd: update to latest Git HEAD
Jo-Philipp Wich [Fri, 12 Aug 2022 19:37:05 +0000 (21:37 +0200)]
rpcd: update to latest Git HEAD

ae5afea ucode: parse ucode plugin scripts in raw mode, init search path

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 66a360206e341abdd1e5560e9cb522d8e453b095)

2 years agouhttpd: update to latest Git HEAD
Jo-Philipp Wich [Fri, 12 Aug 2022 19:24:26 +0000 (21:24 +0200)]
uhttpd: update to latest Git HEAD

e3395cd ucode: initialize search path before VM init
8cb3f85 ucode: initialize default library search path
188dea2 utils: accept '?' as path terminator in uh_path_match()
c5eac5d file: support using dynamic script handlers as error pages
290ff88 relay: trigger close if in header read state with pending data
f9db538 ucode: ignore exit exceptions
8ba0b64 cmake: use variables and find_library for dependency

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 4ee77cfcfadcd2b28678a1f3e8e78383b0b21963)

2 years agoucode: update to latest Git HEAD
Jo-Philipp Wich [Wed, 29 Jun 2022 18:19:35 +0000 (20:19 +0200)]
ucode: update to latest Git HEAD

bcdd2cb examples: add module search path initialization and freeing
ee1946f ubus: fix GCC strncpy() truncation warning
131d99c lib: introduce three new functions call(), loadstring() and loadfile()
8e8dae0 lib: introduce helper function for indenting error messages
476f02b lib: simplify include_path()
d84b53a source: avoid null pointer access in uc_source_runpath_set()
c43a54f types: gracefully handle unpatched upvalues in ucv_free()
e2fb11a README.md: document gc() function
b41cb2d main: introduce -g flag to allow enabling periodic gc from cli
85d7885 lib: implement gc()
47528f0 vm: support automatic periodic GC runs
381cc75 types: treat vm->exports as GC roots
fcc49e6 compiler: add import statement support for dynamic extensions
c9442f1 vm: introduce new I_DYNLOAD opcode
b6fd8a2 lib: internally expose new uc_require_library() helper
a486adc vm: don't treat offset 0 special for exceptions
41ccd19 compiler: don't treat offset 0 special at syntax errors
b4a3f68 compiler: improve formatting of nested syntax error messages
5d5dadc program: remove now unused uc_program_export_lookup()
304995b compiler: rework export index allocation
506cc37 compiler: fix deriving module path from source runpath
54b7fac compiler: enforce stricter module compilation rules
d62e372 vm: don't initialize upvalues for module functions
b856602 program: add serialization and deserialization for module function flag
d7d1bde compiler: add a flag denoting module functions
156d584 treewide: unexport libucode internal functions
10e056d compiler: add support for import/export statements
862e49d compiler: resolve predeclared upvalues
78dfb08 compiler: require a name in function declarations
afd78c1 compiler: fix reported source position in inc/dec operator error
e1c3db0 tests: run_tests.sh: substitute dynamic test directory path in output
3c168b5 vm, cli: move search path into global configuration structure
d85bc71 vm: introduce import and export opcodes
365782e vm: honor constant flag of objects and arrays
6becc64 vm: transparently resolve upvalue references
3418967 vm: gracefully handle unresolved upvalues
50cf572 program: add function to globally lookup exported name
c441f65 program: add infrastructure to handle multiple sources per program
2322468 program: fix reporting source position of first instruction
9c9a9ec program: fix en/decoding debuginfo upvalue slots in precompiled bytecode
41114a0 source: add tracking of exported symbols
70ae304 lib: honor constant flag of arrays
3c104f5 types: resolve upvalue references on stringification
3a6f9cb types: add ability to mark array and object values as constant
b738f3a lexer: recognize module related keywords
03c8e4b lexer: rewrite token scanner
fd433aa lexer: fix parsing with disabled block left stripping
557577a rtnl: fix parsing/creation of IFLA_AF_SPEC RTA for the AF_BRIDGE family
35c6b73 compiler: fix stack mismatch on continue statements nested in switches
f673096 uloop: end uloop on exceptions in managed code
2e5426c ubus: end uloop on exceptions in managed code
c024270 rtnl: expose IFLA_STATS64 contents
d3c58c0 rtnl: expose ifinfomsg.ifi_change member
c4dde50 rtnl: update NETLINK_GET_STRICT_CHK socket flag with every request
7ef0d02 nl80211: fix NL80211_SURVEY_INFO_NOISE datatype
9a2e592 compiler: fix stack mismatch on nonmatching switch statements with locals
03c8ca5 nl80211: recognize further NL80211_STA_INFO_* NLAs
a1ed566 struct: add optional offset argument to `unpack()`
230e595 rtnl: fix segmentation fault on parsing linkinfo RTA without data
523566d rtnl: zero request message headers
56be30d rtnl: fix premature netlink reply receive abort
1347440 rtnl: avoid stray "netlink: %d bytes leftover after parsing attributes."
44b0a3b struct: fix packing `*` format after other repeated formats

Also package uloop binding module which has been introduced by a previous
ucode update and introduce a host build with the basic set of modules.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 3446d32616efad335c4eeeafc2f542089839bf20)

2 years agonftables: fix parsing date expressions
Jo-Philipp Wich [Mon, 8 Aug 2022 22:05:02 +0000 (00:05 +0200)]
nftables: fix parsing date expressions

Musl libc does not support the non-POSIX "%F" format for strptime() so
replace all occurrences of it with an equivalent "%Y-%m-%d" format.

Fixes: #10419
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit e6e4f979999393825370e9db9fe04d75cb01acf2)

2 years agofirewall4: update to latest Git HEAD
Jo-Philipp Wich [Wed, 24 Aug 2022 21:04:45 +0000 (23:04 +0200)]
firewall4: update to latest Git HEAD

a4484d4 fw4: support automatic includes
ca7e3a1 fw4: honour enabled option of include sections
5a02f74 tests: add missing fs.stat) mock data for `nf_conntrack_dummy`
111a7f7 fw4: don't inherit zone family from ct helpers

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit fe86b2ffaaf6059250e3ba0a9e1436312415e23f)

2 years agoipq806x: add missing scaling_available_frequencies for dedicated cpufreq
Christian Marangi [Sun, 21 Aug 2022 16:52:52 +0000 (18:52 +0200)]
ipq806x: add missing scaling_available_frequencies for dedicated cpufreq

Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.

Fixes: 5dbbefcbccc0 ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[ fix conflict by dropping 5.15 patch not present in openwrt-22.03 ]
(cherry picked from commit d6994c53cd0e5334478d2aab424674da438804e2)

2 years agomac80211: parse the correct set of HE capabilities for AP mode
Sultan Alsawaf [Fri, 22 Jul 2022 06:36:31 +0000 (23:36 -0700)]
mac80211: parse the correct set of HE capabilities for AP mode

It is common for 802.11ax NICs to support more than just AP mode, which
results in there being a distinct set of HE capabilities for each mode. As
(bad) luck would have it, iw prints out info for each HE mode in sequential
order according to `enum nl80211_iftype`, and AP mode isn't always first.

As a result, the wrong set of HE capabilities can be parsed if an AP NIC
supports station (managed) mode or any other mode preceding AP mode, since
only the first set of HE capabilities printed by iw is parsed from awk's
output.

This has a noticeable impact on beamforming for example, since managed mode
usually doesn't have beamformer capabilities enabled, while AP mode does.
Hostapd won't be set up with the configs to enable beamformer capabilities
in this scenario, causing hostapd to disable beamforming to HE stations
even when it's supported by the AP.

Always parse the correct set of HE capabilities for AP mode to fix this.
This is achieved by trimming all of iw's output prior to the AP mode
capabilities, which ensures that the first set of HE capabilities are
always for AP mode.

Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
(cherry picked from commit f338f76a66a50d201ae57c98852aa9c74e9e278a)

2 years agoramips: get MAC addr from the encrypted partition (WG4хх223)
Mikhail Zhilkin [Sat, 9 Jul 2022 17:09:57 +0000 (17:09 +0000)]
ramips: get MAC addr from the encrypted partition (WG4хх223)

This commit resolves #10062. Adds decryption of the Arcadyan WG4xx223
configuration partition (board_data)to get base MAC address from it.
As a result, after this change the hack with saving MAC addressees to
u-boot-env before installation of OpenWrt is no longer necessary.

This is necessary for the following devices:
- Beeline Smartbox Flash (Arcadyan WG443223)
- MTS WG430223 (Arcadyan WG430223)

Example:
+----------------+-------------------+------------------------+
|                |    MTS WG430223   | Beeline Smartbox Flash |
+----------------+-------------------+------------------------+
| base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06      |
| label          | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09      |
| LAN            | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09      |
| WAN            | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06      |
| WLAN_2g        | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07      |
| WLAN_5g        | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07      |
+----------------+-------------------+------------------------+

Collected statistic shows that the 2-4th bits of the 7th byte of the
WLAN_5g MAC are the constant (see #10062 for more details):
- Beeline Smartbox Flash - 100
- MTS WG430223 - 010

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit a6b0d0806055a53a2538df83f8322c38ee9f3441)

2 years agobase-files: add mtd_get_mac_encrypted_arcadyan function
Mikhail Zhilkin [Tue, 12 Jul 2022 14:52:04 +0000 (14:52 +0000)]
base-files: add mtd_get_mac_encrypted_arcadyan function

Some Arcadyan devices (e.g. MTS WG430223) keep their config in encrypted
mtd. This adds mtd_get_mac_encrypted_arcadyan() function to get the MAC
address from the encrypted partition. Function uses uencrypt utility for
decryption (and openssl if the uencrypt wasn't found).

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 12c971bc26ac0ff04257bc475fff6fa68068c6c0)